Sophos CS101-8 Manual de usuario
Quick Start Guide
Sophos Switch Series
1
For more information about your switch, scan the QR code or visit www.sophos.com/get-started-switch
1. Before Deploying
Congratulations on the purchase of your Sophos Switch. This Quick Start Guide describes in short steps
how to connect your switch and do the initial configuration. Before you begin, please make sure you have
access to Sophos Central which is needed to manage your switch. Please ensure you have a valid license
to manage the switch.
a) What is included in the box
Quick Start Guide Sophos Switch Series
Sophos Switch
Power Adapter
(region-specific)
CS101-8 model only
Power Adapter
CS101-8FP model only
Power cable
(region-specific)
(except CS101-8/8FP)
RJ45 to DB9
Console cable
(except CS101-8/8FP)
Rubber feetThis Quick Start Guide and
Safety Instructions
Rackmount Kit
(except CS101-8/8FP)
ENGLISH
2
b) Appliance images: front and back
* CS101-8FP model shown, other models may vary
** CS110-48FP model shown, other models may vary
*** CS210-48FP model shown, other models may vary
ENGLISH
CS101-8x*CS110-xx**
Console port
Status LEDs
LED/Mode button (PoE model only)
24/48 x 10/100/1000 Mbps copper ports 4 x 1/10 Gbps
SFP+ ports
CS210-24/48FP***
CS210-8FP
Power cable connector
LED/Mode button
(PoE model only)
8 x 10/100/1000
Mbps copper ports
2 x 1 Gbps
SFP ports
Status LEDs
Power supply
connector
Power
switch
Ground connector
Power cable connector
Power supply connector
Console port
Status LEDs
LED/Mode button
24/48 x 10/100/1000
Mbps copper ports
4 x 1/10 Gbps
SFP+ ports
8/16 x 100/1000/2500
Mbps copper ports
Console port
Status LEDs
LED/Mode button 8 x 100/1000/2500
Mbps copper ports
4 x 1/10 Gbps
SFP+ ports
Quick Start Guide Sophos Switch Series
3
c) Interfaces
Model 1G LAN Ports 2.5G LAN ports SFP/SFP+ Fiber ports Max. PoE Capacity Max. 15W/30W/60W PoE Devices
CS101-8 8 0 2 SFP N/A N/A
CS101-8FP 8 0 2 SFP 110W 7/3/-
CS110-24 24 0 4 SFP+ N/A N/A
CS110-24FP 24 0 4 SFP+ 410W 24/13/-
CS110-48 48 0 4 SFP+ N/A N/A
CS110-48P 48 0 4 SFP+ 410W 26/13/-
CS110-48FP 48 0 4 SFP+ 740W 48/24/-
CS210-8FP 0 8 4 SFP+ 240W 8/8/4
CS210-24FP 16 8 4 SFP+ 410W 24/13/-
CS210-48FP 32 16 4 SFP+ 740W 48/24/-
Note: All ports on a PoE model are PoE capable according to 802.3af/at standard, CS210-8FP also supports the 802.3bt standard
Other Interfaces Type Comment
COM RJ45 You can connect a serial console to the RJ45 COM port to access the Command Line Interface (CLI).
The required connection settings are:
ÌBits per second: 115,200
ÌData bits: 8
ÌParity: N (none)
ÌStop bits: 1
Reset Button Press and hold the reset button for 7 seconds to reset the switch to the factory default
settings. All configuration including the login password will be reset.
ENGLISH
Quick Start Guide Sophos Switch Series
4
2. Mount and Power Up the Switch
Mount the switch in the rack
If you want to mount the switch in a rack, please use the supplied rackmount kit for this device where
available. For instructions on how to mount your switch, please see the Operating Instructions under
www.sophos.com/get-started-switch
Connect the power cable and turn on the switch
Connect the power supply (where available) and/or supplied power cable to the switch and turn it on (if
unit has a power button). After a few seconds, the Power LED will start blinking and the switch will boot.
This process should take just a few minutes. After the boot-up is complete the Power LED will turn to
solid green.
Connect Grounding Cable (CS101-8x models only)
If ethernet cables are run between buildings or if the switch is used in a high lightning exposure area,
connect a safety ground wire to the grounding screw to provide additional protection from electrical
shock. If unsure of your electrical ground, consult an electrician.
Internet
e.g., DSL modem
Firewall
Switch
ENGLISH
Quick Start Guide Sophos Switch Series
5
3. Connect the Switch to your Network
Connect any port on the switch to the next-hop ethernet switch or Sophos Firewall. After powering on,
the switch will boot and attempt to get an IP address from a DHCP server (either from the Sophos firewall
or another DHCP server in your network).
If the switch is unable to get an IP address from a DHCP server and is not registered in Sophos Central
within 15 minutes, it will use a default IP address 172.16.16.239. To manually configure your switch,
adjust the network settings of your administration PC (PC/laptop) so that it is on the same network as
the switch. For example:
ÌIP Address: 172.16.16.230
ÌNetmask: 255.255.255.0
Connect your Administration PC/laptop to port 1 of the switch.
Open a browser and enter the IP address of the switch: https://172.16.16.239 and complete the setup
and configuration.
If you want to attempt registration with DHCP again, correct the fault that prevented the switch from
getting a DHCP assigned IP address and power cycle the switch either manually or via the switch
management interfaces (CLI or HTTPS web interface).
Please Note: If the switch is still unable to retrieve an IP address from the DHCP server it will use the
default IP address 172.16.16.239.
4. Set Up the Switch
a. Sign in to Sophos Central at central.sophos.com
If you don’t yet have a Sophos Central Account, please create one.
b. Register the switch in your Sophos Central account by entering the serial number.
Note: After powering on the switch, there is a 15-minute window to register the switch in Sophos
Central. If the network administrator does not register the switch within this time period, the switch will
have to be either hard rebooted or rebooted using the local web interface.
c. After the switch is registered in Sophos Central, it is upgraded to the latest firmware version.
ENGLISH
Quick Start Guide Sophos Switch Series
6
5. Sign in to your Sophos Switch
Sophos provides users an option to sign in to the switch for advanced configuration. The advanced
options can be configured in the on-box web interface of the switch or through its command line
interface (CLI).
1.Register the switch in Sophos Central as mentioned in the above section.
2.An IP Address will be assigned to the switch from either Sophos Central or the DHCP server
3.Open a web browser on your computer enter the IP address and press enter.
4.In order to access the CLI or the web interface of the switch after registering it in Sophos Central, use
the default credentials with the username as "admin" and the unique password for this switch.*
6. Managing the Switch via the Console Port
1.Connect the switch console port (not available on CS101-8/8FP models) to a computer using the
console cable provided.
2.Launch any terminal emulation program, e.g., PuTTy
3.Select the COM port, and use the following settings:
Baud Rate: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow Control: None
4.Press Enter on your keyboard to connect to the CLI.
5.Sign in using the username “admin” and the unique password for this switch.*
ENGLISH
* The unique password is printed on a sticker (see picture to the right) affixed to the
chassis of the switch and on an additional sticker in the packaging materials. duEg3@!oQb
Quick Start Guide Sophos Switch Series
7
7. Connecting Power over Ethernet (PoE) Devices
All ports on PoE-capable switches can provide Power over Ethernet (PoE) to a connected PoE device
which conforms with the 802.3af (max. 15.4W) or 802.3at (max.30W) standards. Each port can provide
up to a maximum of 30 Watts.
Please note: If the total power consumption of all PoE-powered devices exceeds the power budget of the
switch, the PoE Max LED will turn on. The port with the highest number and the lowest priority (according
to the per-port priority settings configured), will no longer receive power and the PoE Mode LED for that
port will be turned off.
To avoid such situations, Sophos recommends calculating the number of connected devices based upon
their max. power consumption (see table "interfaces" above).
8. LED Status
Status LEDs
Power Green Solid Power On
Off Power Off
Fault Amber Solid Error
Off Normal Behavior
PoE Max Amber Solid The power requested by PoE devices exceeds total PoE limit
of the switch. No additional devices can be powered.
Off Additional PoE devices may still be powered
LAN Mode*Green Solid The left LED on RJ45 ports indicates Speed
PoE Mode*Green Solid The left LED on RJ45 ports indicates PoE status
* By pressing the “LED mode” button you can switch the meaning of the left LED on each RJ45 port (labeled with “mode”) between LAN
Mode and PoE Mode.
ENGLISH
Quick Start Guide Sophos Switch Series
8
LEDs on each RJ45 Ethernet Connector
LK/AT
(Link/Activity)
(Right LED)
Green Solid 1. Ethernet port has established link.
2. Good connection between the ethernet
port and connected device.
Flashing The port is sending or receiving network data.
Off 1. The adapter and switch are not receiving power.
2. No connection between both ends of network.
3. Network drivers have not been loaded or do not function correctly.
CS101-xx Models
Speed
(Left LED)
[on PoE models: LED Mode button not pressed]
Green Solid Ethernet port is operating at 1000 Mbps.
Off Ethernet port is operating at 100 0r 10 Mbps (if LK/AT LED is active).
1G Ports on CS110-xx and CS210-xx Models
Speed
(Left LED)
[on PoE models: LED Mode button not pressed]
Green Solid Ethernet port is operating at 1000 Mbps.
Amber Solid Ethernet port is operating at 100 Mbps.
Off Ethernet port is operating at 10 Mbps (if LK/AT LED is active).
2.5G Ports on CS210-xx Models
Speed
(Left LED)
[on PoE models: LED Mode button not pressed]
Green Solid Ethernet port is operating at 2500 Mbps.
Amber Solid Ethernet port is operating at 1000 or 100 Mbps.
Off Ethernet port has no link
CS101-8FP (PoE) Models only
Mode
(Left LED)
[LED Mode button pressed]
Green Solid PoE switch provides power to the port
Off No power is provided to the port
CS110/210 P/FP (PoE) Models only
Mode
(Left LED)
[LED Mode button pressed]
Green Solid PoE switch provides power to the port
Amber Solid Error
Off No power is provided to the port
Quick Start Guide Sophos Switch Series
ENGLISH
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de Sophos
