Sony PFV-L10 Manual de usuario

INTERFACE UNIT

PFV-L10

INSTALLATION MANUAL

2nd Edition (Revised 1)

Serial No. 17001 and Higher

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

PFV-L10

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the specifications of the Operation Manual.

6. When performing the installation, keep the rear of

the unit 10 cm (4 inches) or more away from walls

in order to obtain proper exhaust and radiation of

heat.

For the U.S.A.

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

1 (E)

PFV-L10

Table of Contents

Manual Structure

Purpose of this manual ......................................................................................... 3(E)

Contents ................................................................................................................ 3(E)

Related manuals.................................................................................................... 4(E)

1. Installation

1-1. Installation Procedure.............................................................................1-1(E)

1-2. Operating Environment ..........................................................................1-1(E)

1-3. Power Supply .........................................................................................1-2(E)

1-3-1. Power Supply Specifications.................................................1-2(E)

1-3-2. Recommended Power Cord...................................................1-2(E)

1-4. Installation Space ...................................................................................1-3(E)

1-5. Installing Optional Board .......................................................................1-4(E)

1-6. Rack Mounting.......................................................................................1-6(E)

1-6-1. Notes on Rack Mounting ......................................................1-6(E)

1-6-2. Rack Mounting Procedure.....................................................1-7(E)

1-7. Matching Connector...............................................................................1-8(E)

1-8. Signal Inputs/Outputs.............................................................................1-8(E)

1-9. Optional Accessories..............................................................................1-8(E)

3 (E)

PFV-L10

Purpose of this manual This manual is the installation manual of Interface Unit PFV-L10.

This manual is intended for use by trained system and service engineers, and

describes the information for installation of the unit.

Contents This manual is organized by following sections.

Section 1 Installation

1-1. Installation Procedure

This section explains the installation procedure with a flowchart.

1-2. Operating Environment

This section describes the operating environment such as operating temperature/

humidity, and mass of the unit.

1-3. Power Supply

This section describes the power supply, recommended power cord, and the

notes for power supply.

1-4. Installation Space

This section describes the dimensions of the unit.

1-5. Installing Optional Board

This section explains the installation procedure of the optional board.

1-6. Rack Mounting

This section explains the rack mounting procedure of the unit in the 19-inch

standard rack.

1-7. Matching Connector

This section describes the type of connector at the rear panel and the matching

connector.

1-8. Signal Inputs/Outputs

This section describes the connector pin assignments at the rear panel.

1-9. Optional Accessories

This section describes the optional boards and rack mount kit.

Manual Structure

4 (E) PFV-L10

Related manuals The following manuals are prepared for PFV-L10.

• Operation Manual (Supplied with PFV-L10)

This manual describes the notes on operating, the locations and functions of parts,

and controls of PFV-L10.

• Maintenance Manual (Available on request)

This manual describes the information for periodic maintenance and detailed

service.

If this manual is required, please contact your local Sony Sales Office/Service

Center.

1-1 (E)

PFV-L10

Section 1

Installation

End

Start

Determining the Location of Installation

1-2. Operating Environment

1-3. Power Supply

1-4. Installation Space

Installing the Optional Board

1-5. Installing Optional Board

1-6. Rack Mounting

Connection

Rack Mounting

1-1. Installation Procedure

The installation procedure of PFV-L10 is as shown in the

following flowchart.

Refer to the each item in this manual for details.

1-2. Operating Environment

Operating temperature 5 dC to 40 dC

Performance temperature 10 dC to 35 dC

Humidity 10 to 90 % (No condensation)

Mass: Approx. 7 kg

(Without the optional board)

To prevent overheating of PFV-L10, ensure that there is

good air circulation around the unit.

Install in a stable location.

Installation on unstable or tilting surface may cause the

unit fall off, resulting in injury.

PFV-L10

1-2 (E)

AC Inlet

(Main unit)

AC Inlet

(Main unit)

1-3-2. Recommended Power Cord

This unit does not come with a power cord.

To get a power cord, please contact your local Sony Sales

Office/Service Center.

.Use the approved Power Cord (3-core mains lead)/

Appliance Connector/Plug with earthing-contacts that

conforms to the safety regulations of each country if

applicable.

.Use the Power Cord (3-core mains lead)/Appliance

Connector/Plug conforming to the proper ratings (Volt-

age, Ampere).

If you have questions on the use of the above Power Cord/

Appliance Connector/Plug, please contact your local Sony

Sales Office/Service Center.

.Never use an injured power cord.

For customers in the U.S.A. and Canada

Required Part

1Power cord, 125 V 10 A (2.4 m) : !1-557-377-11

For customers in the United Kingdom

Required Part

2Power cord, 250 V 10 A (2.4 m) : !1-782-929-21

If the unit is used in the area except above, please contact

your local Sony Sales Office/Service Center.

1-3. Power Supply

1-3-1. Power Supply Specifications

Power voltage AC 100 V to 240 V

Power frequency 50 Hz or 60 Hz

Power consumption Max. 13 A, +5 V/DC

(With the optional boards installed)

Rush current AC 120 V IN : 20 A

AC 240 V IN : 55 A

AC power supply is required a capacity which is commen-

surate with rush current.

If the capacity of the AC power supply is not enough, the

breaker of AC power of a supply side may operate or this

unit may not operate normally.

1-3. Power Supply

1-3 (E)

PFV-L10

1-4. Installation Space

Do not block the ventilation holes of the unit.

Both of the front and rear sides must be at least 20 cm away from the walls for ventilation and mainte-

nance.

The outer dimensions of PFV-L10 are as shown here:

1-4. Installation Space

15.3

3-M4

76.2 353.2

91.7 231

115.5

88 (2U)

465

440

482

Unit: mm

PFV-L10

1-4 (E)

1-5. Installing Optional Board

Board retainer

PSW 3x6

MB-862 board

Side A

Board lever

Board guide rails

Main board

Board lever

Screws

Front panel

4. Insert the optional board along the board guide rails

with the board lever turned in the direction of the

arrow 1, securely connect it to the MB-862 board by

pushing.

5. Stick the slot label supplied with the optional board

onto the board lever.

6. Reinstall the board retainer.

7. Reinstall the front panel.

When removing the main board, turn the board lever in the

direction of the arrow 2, and pull out the board to ward

you.

1-5. Installing Optional Board

The optional board can be installed in any empty slot of

PFV-L10.

Installing Main Board (Front side)

1. Turn off the power switches A and B of PFV-L10.

2. Remove the front panel after loosening the two screws

on the panel.

3. After removing the two screws, remove the board

retainer.

Otros manuales para PFV-L10

Tabla de contenidos

Otros manuales de Equipo de grabación de Sony

Sony

Sony SEQ-V902 Manual de usuario

Sony

Sony HSR-J2009 Manual de usuario

Sony

Sony PFV-D50A Manual de usuario

Sony

Sony PFV-HD50A Manual de usuario

Sony

Sony DMX-R100 Manual de usuario

Sony

Sony TC-177SD Guía de configuración

Sony

Sony SLV-E510EE Manual de usuario

Sony

Sony PCM-R300 Manual de usuario

Sony

Sony BDX-N1000 Manual de usuario

Sony

Sony PFV-L02 Manual de usuario

Sony

Sony MU-R201 Manual de usuario

Sony

Sony SEG-2550 Manual de usuario

Sony

Sony MSW-A2000 Manual de usuario

Sony

Sony BKSM-T101 Manual de usuario

Sony

Sony TC-366 Guía de configuración

Sony

Sony TC-42 Manual de usuario

Sony

Sony SVR-HDT1000 Manual de usuario

Sony

Sony BDX-N1000 Manual de usuario

Sony

Sony BKP-7933 Manual de usuario

Sony

Sony SEQ-421 Manual de usuario

Sony

Sony PCM-D50 - Portable Linear Pcm Recorder Manual de usuario

Sony

Sony DMW-S01NL Manual de usuario

Sony

Sony CDR-W33 Manual de usuario

Sony

Sony RCD-W10 - Cd/cdr Recorder/player Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado