Sony GDM-1962B Manual de usuario

This document contains instructions to connect a Sun Microsystems/Sony GDM-1662B and

GDM-1962B color monitor to a PC system, using the accompanying cable and video card.

Please read the documentation provided with the video card, for more instructions.

Installation Manual Fo

Sun/Sony GDM-1962B

Sun/Sony GDM-1662B

Color Monitor Series

Please read Entirely Before Installation!

Replacement video cards for this monitor can be obtained from: mirage-mmc.com

READ THIS BEFORE INSTALLING THE UNIT:

Please follow these simple instructions, to assure a trouble free monitor

installation:

Your Sun/Sony GDM-16/1962B monitor like many high-end monitors, requires a

special cable to attach to your computer system. This cable is called a 13W3

type cable.

One such cable is usually supplied with your monitor and has a male 13W3

connector on the end which is intended to connect to the 13W3 female

connector, located in the back of the Sun/Sony GDM-16/1962B unit. Below

illustration displays both female (back of the monitor) and male (end of the cable)

13W3 connections.

If your are using the monitor on a PC system:

This monitor requires a special board to run on a PC system. The video card

supplied must have Jumper for Sync on Green (or Composite sync) in “ON”

position. Please make sure that the “Sync-On-Green” Jumper (Usually

identifiable by a Red Colored Plastic Jumper on the video card) is in Engaged

position, as shown in figure 2, below.

Figure 2 – Red

Jumper

Engaged

Figure 1 – Red

Jumper

Removed

Figure A - Female 13W3

connection on monitor's

back. Figure B - Male 13W3

connection on the cable's

end.

Replacement video cards for this monitor can be obtained from: mirage-mmc.com

ADJUSTING THE SCREEN DISTORTIONS:

This unit has been tested and pre-adjusted by trained technicians, prior to

shipping to you. Please do not attempt to adjust the unit using the internal fine

tuning controls, unless you are advised to do so.

If you are experiencing severe screen distortions and you have made sure that

they are not caused because of the incorrect cable installation or sync-on-green

jumper settings for the PC video card. Or if you need to adjust the screen’s

height and width for your Sun/Sony GDM-16/1962B monitor, please locate the

adjustment buttons as shown in the illustration on the next page, by removing the

monitor’s plastic shell, using a screwdriver.

BEFORE ATTEMPTING TO REMOVE THE SHELL, MAKE SURE THAT

THE MONITOR IS TURNED OFF AND THE POWER CABLE IS

COMPLETELY REMOVED FROM THE UNIT.

Once the plastic shell is removed, a metal cage will be exposed.

PLEASE DO NOT ATTEMPT TO REMOVE THE METAL CAGE, AS THE

INTERIOR CIRCUITARY PROTECTED BY THIS SHELL IS LOADED

WITH THOUSANDS OF VOLTS OF ELECTRICITY.

REQUIRED TOOLS: Please notice that to adjust the controls, you’ll need

to use a small plastic tool, usually installed on top of the inner metal cage

of the monitor. If the tool is missing, you may use a small Philips

screwdriver, instead.

WARNING: THE ADJUSTMENT CONTROLS ARE VERY DELICATE

AND MAY BREAK, IF EXCESSIVE FORCE IS USED. PLEASE USE

EXTREME CAUTION WHEN TURNING THE CONTROLS, AS A

BROKEN CONTROL MAY DISABLE YOUR MONITOR AND REQUIRES THE

UNIT TO BE SENT BACK TO REPAIR SHOP FOR NECESSARY REPAIRS.

VERY IMPORTANT: DO NOT ATTEMPT TO ADJUST THE CONTROLS

THAT ARE NOT LISTED ON THIS DOCUMENT OR ARE MENTIONED

AS “DO NOT TO ADJUST” ITEM.

Replacement video cards for this monitor can be obtained from : mirage-mmc.com

POSITION ADJUSTMENT CONTROLS:

This monitor has 2 adjustments (H, L) for each of the controls below. The H (high

settings) is normally the default value and corresponds to 70 to 80 Khz opertaion.

The L (low settings) corresponds to 60 to 65 Khz operation.

V.SIZE or Vertical size adjustment control:

This is your vertical height adjustment. You need to center

the screen vertically first to get this correct.

V.CENT or Vertical center adjustment control:

This control will move the screen up or down (vertical

center). In some cases the companion video card will show

a bigger size for 640x480 and 1280x1024 resolutions than

the 1024x768. In this case if you want to be able to see most resolutions

completely, adjust the monitor for 1280x1024, so that 640x480 will fill up the

screen too.

H.FREQ or Horizontal frequency (kHz) adjustment control:

This needs to be adjusted if you get a scramble picture.

Scramble picture indicates a wrong Horizontal frequency is

getting to the monitor. Turn this control very slowly until

you get a stable picture. This process will effect all resolutions and also

Horizontal Positioning.

H.SIZE or Horizontal Size adjustment control:

This is the monitor’s width size adjustment, you need to

center the screen horizontally first before making this

adjustment. Sometimes increasing the Horizontal size to

the limits may cause the monitor to behave abnormal or the screen may become

shaky. Normally leave about 1/8 of inch of blank border on each side of the

screen, for the best result. This is needed for the proper monitor timing

adjustment.

PIN BAL or Screen geometry balance control:

Do not touch this control, unless the screen is not straight

from the sides.

V.LIN or Vertical Linearity control:

Do not touch this at all. This makes the vertical picture to

be closer in certain areas (to be less linear).

V. LIN BAL or Vertical linearity balance control:

Do not try to adjust this control.

PIN AMP or Pin cushioning adjustment control:

This makes the right side and the left side to be made

concave or convex. Also see PIN BAL above to see which

area of the sides this is effecting more.

KEY control:

Moves the screen geometry by moving all four sides of a

trapezoid. Do not touch this. This and KEY BAL and PIN

BAL and PIN AMP have to be adjusted together. Changing

one without the others may make the screen to be uneven from the sides.

KEY BAL or Screen geometry balance control:

Do not touch this control, unless the screen is not straight.

H.PHASE or Horizontal Phase adjustment control:

This moves the screen to the right and left. There is

another centering location as mention above, in the left

side of the monitor and it is marked H-CENT.

FOCUS ADJUSTMENT CONTROLS:

H.STAT or Horizontal Convergence Control:

Functions similarly to the controls at front of the monitor.

SCREEN Control: Screen Brightness.

H.FOCUS Control: Horizontal Focus Adjustment.

V.FOCUS Control: Vertical Focus Adjustment.

H-CENT Control: Horizontal position centering.

V-STAT or Vertical Convergence Control:

Functions more detailed in comparison to the one located at front of

the monitor, with 3 different control areas: Top (TOP), Center (CTR)

and Bottom (BTM).

Replacement video cards for this monitor can be obtained from: mirage-mmc.com

Monitor SPECIFICATION:

Vertical refresh rate : 60-85 Hz

Horizontal Scan rate: 60- 80 KHz (Kilo Hetrz). Default set to 72Khz

Horizontal scan rate is adjusted by H.Freq (Hold) as mentioned above.

Maximum Resolution: 1600x1200

Monitor Adjusted for: 1024x768

Tube: Sony Trinitron

There is no vertical hold adjustment on this monitor.

If the monitor rolls vertically on some resolutions, you have to adjust the video

card's refresh rate to be adjusted near 80 Hz (not 85 Hz). In this case you need

to make sure that you have a Video card with a -1662 or -1097 specification (not

7285; 7285 spec may roll on some Sony 1962/1662 monitors)

This monitor requires a special video card to run all the modes properly on a PC.

For more information, please refer to www.mirage-mmc.com

This monitor does not function with a laptop/notebook running at 31.5 Khz( VGA

standard).

SONY Tube mask lines:

This monitor has 2 very fainted horizontal lines across the screen. This is how

SONY Trinitron Monitors are made to connect the tube masks together and this

is not a monitor defect. For further Information, please contact www.sony.com.

Monitor Labels and handling:

ü Please take extra caution when lifting this monitor. Normally we recommend 2

people to carry a 19" or higher size monitor as the monitor may weigh over 70

lbs.

ü In some cases, the serial # and front Logo of this monitor may have been

removed/replaced by the Manufacturer (HP, SUN Micro Systems, ...) so that

the original warranty is not provided from the manufacturer.

ü The 90 day limited warranty is provided by Multimedia Computers.

ü This monitor is carefully tested and refurbished to have the original display

specification. We apologize for any imperfections on the casing (bezel) as

these may not be new monitors.

Replacement video cards for this monitor can be obtained from: mirage-mmc.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Sony

Sony

Sony LY51 Manual de usuario

Sony

Sony Trinitron CPD-300SF Manual de usuario

Sony

Sony LMD-X3200MD Manual de usuario

Sony

Sony CPD-E540 Marketing Specifications (includes Comparison... Manual de usuario

Sony

Sony SDM-X75FB Manual de usuario

Sony

Sony SDM-S51 Manual de usuario

Sony

Sony LMD-2451MT Manual de usuario

Sony

Sony LMD-1950MD Manual de usuario

Sony

Sony FWD-32LX2X Manual de usuario

Sony

Sony PLM-A35 - Glasstron - 0.55" LCD Passive Matrix Head Mounted... Manual de usuario

Sony

Sony FD Trinitron CPD-L181A Manual de usuario

Sony

Sony Trinitron CRT Monitor Manual de usuario

Sony

Sony PVM-2030/BS Manual de usuario

Sony

Sony Triniton GDM-20SHT Manual de usuario

Sony

Sony Trinitron HMD-A100 Manual de usuario

Sony

Sony Trinitron KV-27S42 Manual de lista de piezas

Sony

Sony XVM-H65 - Monitor Manual de usuario

Sony

Sony BVM-F250 Manual de usuario

Sony

Sony MFM-HT75W Instrucciones de montaje

Sony

Sony XVM-H6 Manual de usuario

Sony

Sony SDM-X53 Operating Instructions (primary... Manual de usuario

Sony

Sony LMDDM30C Manual de usuario

Sony

Sony FWD-32LX1 Manual de usuario

Sony

Sony BRAVIA FW-75BZ40H Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación