Sony FWD-50PX3 - 50" Plasma Panel Manual de usuario

FLAT WIDE DISPLAY MONITOR

FWD-50PX3

PROTOCOL MANUAL (For Customer)

FWD-50PX3

Table of Contents

1. Communication Parameters ......................................................... 1

2. Pin Assignment..................................................................................... 1

3. Communication Data Format ....................................................... 1

4. General Function ................................................................................. 3

5. Analog Signal Detect Function ................................................... 9

6. Priority Signal Select Function ................................................. 10

7. Picture/Sound ...................................................................................... 14

8. Size/Shift ................................................................................................. 17

9. Status Enquiry..................................................................................... 20

10. User Reset.............................................................................................. 24

FWD-50PX3

1. Communication Parameters

Communication method RS-232C

Synchronous method Asynchronous

Baud rate 9600bps

Character length 8bit

Parity None

Start bit length 1bit

Stop bit length 1bit

Flow control None

2. Pin Assignment

12345

Monitor side (D-sub 9-pin)

_External view _

6789

12345

6789

Host side (D-sub 9-pin)

_External view _

Pin No. Function

1NC

2 TXD

3 RXD

4NC

5 GND

6NC

7NC

8NC

9NC

Pin No. Function

1NC

2 RXD

3 TXD

4NC

5GND

6NC

7NC

8NC

9NC

3. Communication Data Format

(a) Control message

No. Item Value

1 Header 0x8C: Control

2 Category 0xXX

3 Function 0xXX

4 Data1 (Length) 0xXX

5 Data2 (Data1) 0xXX

: : 0xXX

X DataX 0xXX

X+1 Check Sum 0xXX

*Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a

value exceeds 255 (1byte).

*Set the command interval to 500 ms or more when transmitting the

Control command continuously.

*Set the command interval to 500 ms or more when transmitting the same

command (Enquiry) after the Control command.

(b) Enquiry message

No. Item Value

1 Header 0x83: Enquiry

2 Category 0xXX

3 Function 0xXX

4 Data1 0xFF

5 Data2 0xFF

6 Check Sum 0xXX

*Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a

value exceeds 255 (1byte).

2FWD-50PX3

4Error answer

No. Item Value

1 Header 0xE0: Answer

2 Answer*0x00: No Function Error

0x01: Check Sum Error

0x02: Data Length Error

3 Check Sum 0xXX

*0x00: No Function Error Packet header,category or function code are

not included in this protocol.

0x01: Check Sum Error Check sum value or received packet is not

correct.

0x02: Data Length Error Packet is correctly received,but the data size

is over the upper limit.

1Control answer

No. Item Value

1 Header 0x70: Answer

2 Answer*0x00: Completed

0x01: Limit Over

0x02: Limit Under

0x03: Command Canceled

3 Check Sum 0xXX

*0x00: Completed Packet is correctly received and process

is also correctly completed.

0x01: Limit Over Packet is correctly received, but the data

value is over the upper limit.

0x02: Limit Under Packet is correctly received, but the data

value under the lower limit.

0x03: Command Canceled Packet is correctly received, but the data

value is not correct or the request cannot

be accepted in the current host state.

*Check Sum: Sum total of 1 to X. Lower one-byte data

is validated when a value exceeds 255

(1byte).

2Enquiry answer (Complete)

No. Item Value

1 Header 0x70: Answer

2 Answer 0x00: Completed

3 Return Data Size 0xXX

4 Return Data1 0xXX

: : 0xXX

X Return DataX 0xXX

X+1 Check Sum 0xXX

*0x00: Completed Packet is correctly received and process is also

correctly completed.

*Return Data: Returns the read value.

*Check Sum: Sum total of 1 to X. Lower one-byte data is validated

when a value exceeds 255 (1byte).

3Enquiry answer (Command cancel)

No. Item Value

1 Header 0x70: Answer

2 Answer 0x03: Command Canceled

3 Check Sum 0x73

0x03: Command Canceled Packet is correctly received, but the data

value is not correct or the request cannot

be accepted in the current host state.

FWD-50PX3

4. General Function

(a) Mode Control

Syntax Header Category Function Data1 Data2 Check Sum

Control 0x8C 0x00 Code Table (1-a) [a] 0x02 Code Table (1-a) [b] 0xXX

Enquiry 0x83 0xFF 0xFF 0xXX

Answer Header Answer Check Sum

Control 0x70 0x00 0x70 Completed

0x70 0x01 0x71 Limit Over

0x70 0x02 0x72 Limit Under

0x70 0x03 0x73 Command Canceled

Answer Header Answer Return to Data Size Return Data1 Check Sum

Enquiry 0x70 0x00 0x02 Code Table (1-a) [b] 0xXX Completed

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x00 Power 0x00 OFF Yes Yes Enable Enable

0x01 ON

0x01 Input Select*40x08 INPUT1 RGB (Analog) Yes Yes Disable Enable

0x09 INPUT1 YUV (Analog)

0x0C OPTION1 VIDEO

0x0D OPTION1 S-VIDEO

0x0E OPTION1 RGB

0x0F OPTION1 COMPONENT

0x10 OPTION2 VIDEO

0x11 OPTION2 S-VIDEO

0x12 OPTION2 RGB

0x13 OPTION2 COMPONENT

0x20 Input1 DVI

0x84 Option1 Digital1

0x85 Option1 Digital2

0x02 Force Status Display 0x00 ON Yes Yes Disable Enable

0x01 OFF

0x03 Audio Mute 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x04 Auto Status Display 0x00 ON Yes Yes Enable Enable

0x01 OFF (Continued)

4FWD-50PX3

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x06 Color System 0x00 Auto Yes Yes Disable Enable

0x01 NTSC

0x02 NTSC4.43

0x03 PAL

0x05 PAL-M

0x06 PAL-N

0x07 PAL60

0x0B Picture Inversion 0x00 OFF Yes Yes Disable Enable

0x01 Auto

0x02 On

0x0C Picture Orbit 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x0D Orbit Range 0x00 Small Yes Yes Disable Enable

0x01 Middle

0x02 Large

0x0E Orbit Cycle 0x00 Speed1 (10 sec ) Yes Yes Disable Enable

0x01 Speed2 (30 sec)

0x02 Speed3 (1 min )

0x03 Speed4 (5 min )

0x0F Language 0x00 Japanese Yes Yes Disable Enable

0x01 English

0x02 Deutsch

0x03 Français

0x04 Español

0x05 Italiano

0x10 Index Number 0x01-0xFF Yes Yes Disable Enable

0x12 Standby Power 0x00 Standard Yes Yes Disable Enable

0x01 Low

0x13 ECO Mode 0x00 Off Yes Yes Disable Enable

(Power Saving) 0x01 ECO High

0x02 ECO Low

0x14 Speaker Out 0x00 ON Yes Yes Disable Enable

0x01 OFF

0x18 Sync Mode 0x00 H/Comp Yes Yes Disable Enable

0x01 Video

0x1B Clock Display 0x00 OFF Yes Yes Disable Enable

0x01 ON (Continued)

FWD-50PX3

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x24 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable

(Option1) 0x01 FW10 (VIDEO, S-VIDEO) BNC

0x02 FW11 (BNC)

0x03 Reserved

0x04 FW31/32

0x05 FW50 (RGB)

0x06 FW20 (UART +CTRL-S)

0x07 FW13 (COMPONENT) RCA

0x08 FW15 (HDMI x2)

0x09 FW16 (Digital x1)

0x0A Reserved

0x0B Reserved

0x0C Reserved

0x0D Reserved

0x0E Reserved

0x0F Not Connect

0x25 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable

(Option2) 0x01 FW10 (VIDEO, S-VIDEO) BNC

0x02 FW11 (BNC)

0x03 Reserved

0x04 FW31/32

0x05 FW50 (RGB)

0x06 FW20 (UART +CTRL-S)

0x07 FW13 (COMPONENT) RCA

0x08 FW15 (HDMI x 2)

0x09 FW16 (Digital x 1)

0x0A Reserved

0x0B Reserved

0x0C Reserved

0x0D Reserved

0x0E Reserved

0x0F Not Connect

0x26 Auto Shut OFF 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x27 Auto Screen Adjust 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x30 PAP 0x00 OFF Yes Yes Disable Enable

0x01 P&P

0x02 PinP (Continued)

6FWD-50PX3

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x31 Active Picture 0x00 Left (P&P)/Main (PinP) Yes Yes Disable Enable

0x01 Right (P&P)/Sub (PinP)

0x02 Swap

0x32 Picture Size (P&P) 0x00-0x0E Yes Yes Disable Enable

0x33 Sub Picture Size 0x00 Large Yes Yes Disable Enable

(PinP) 0x01 Small

0x34 Picture Position 0x00 Position1 Yes Yes Disable Enable

(PinP) 0x01 Position2

0x02 Position3

0x03 Position4

0x35 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable

(Left/Main) 0x09 INPUT1 YUV (Analog)

0x0C OPTION1 VIDEO

0x0D OPTION1 S-VIDEO

0x0E OPTION1 RGB

0x0F OPTION1 COMPONENT

0x10 OPTION2 VIDEO

0x11 OPTION2 S-VIDEO

0x12 OPTION2 RGB

0x13 OPTION2 COMPONENT

0x20 INPUT1 DVI

0x84 Option1 Digital1

0x85 Option1 Digital2

0x36 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable

(Right/Sub) 0x09 INPUT1 YUV (Analog)

0x0C OPTION1 VIDEO

0x0D OPTION1 S-VIDEO

0x0E OPTION1 RGB

0x0F OPTION1 COMPONENT

0x10 OPTION2 VIDEO

0x11 OPTION2 S-VIDEO

0x12 OPTION2 RGB

0x13 OPTION2 COMPONENT

0x20 INPUT1 DVI

0x84 Option1 Digital1

0x85 Option1 Digital2

0x40 All White 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x41 BackGround 0x00 Gray Yes Yes Disable Enable

0x01 Dark Gray

0x02 Black (Continued)

FWD-50PX3

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x44 Logo Illumination & 0x00 Logo Off Yes Yes Enable Enable

Status LED 0x01 Logo On (Low)

0x02 Logo On (High)

0x04 LED Off

0x05 LED On

0x45 Control Mode 0x00 Main +Remocon Yes Yes Disable Enable

0x01 Main

0x02 Remocon

0x03 All Off

0x04 Limited*5

0x46 On Off Timer Mode 0x00 Every Day (Repeat) Yes Yes Enable Enable

0x01 Day Of Week

0x47 On Timer Enable bit0 Sunday 1: Enable, 0: Disable Yes Yes Enable Enable

bit1 Monday 1: Enable, 0: Disable

bit2 Tuesday 1: Enable, 0: Disable

bit3 Wednesday 1: Enable, 0: Disable

bit4 Thursday 1: Enable, 0: Disable

bit5 Friday 1: Enable, 0: Disable

bit6 Saturday 1: Enable, 0: Disable

bit7 Every day 1: Enable, 0: Disable

0x48 Off Timer Enable bit0 Sunday 1: Enable, 0: Disable Yes Yes Enable Enable

bit1 Monday 1: Enable, 0: Disable

bit2 Tuesday 1: Enable, 0: Disable

bit3 Wednesday 1: Enable, 0: Disable

bit4 Thursday 1: Enable, 0: Disable

bit5 Friday 1: Enable, 0: Disable

bit6 Saturday 1: Enable, 0: Disable

bit7 Every day 1: Enable, 0: Disable

0x49 Auto Dimmer 0x00 OFF Yes Yes Disable Enable

0x01 ON

0x65 IP Setting Mode 0x00 DHCP Yes Yes Enable Enable

0x01 Manual

0x02 Speed

0x66 IP Setting Execute 0x00 No No Yes Enable Enable

0x01 Yes

0X02 NVR Reset (Continued)

8FWD-50PX3

Code Table (1-a)

[a]Function [b]Range/Switch Code Command

Control Enquiry Standby Power On

0x67 IP Setting Result 0x00 Done Yes No Enable Enable

0x01 Error 1 (UART Commu.)

0x02 Error 2 (Duplication)

0x03 Error 3 (IP Add Setting)

0x04 Error 4 (GW Add setting)

0x05 Error 5 (DNS1 Setting)

0x06 Error 6 (DNS2 Setting)

0x07 Error 7 (Sbnt Msk Setting)

0x68 Speed Setting 0x00 100Mbps/Full Duplex Yes Yes Enable Enable

0x01 100Mbps/Half Duplex

0x02 10Mbps/Full Duplex

0x03 10Mbps/Half Duplex

0x04 Auto

0x70 Input Skip bit0 HD15 Yes Yes Disable Enable

bit1 DVI

bit2 Reserved

bit3 Reserved

bit4 Reserved

bit5 Reserved

bit6 Reserved

bit7 Reserved

0x71 Default Input 0x00 Last Memory Yes Yes Enable Enable

0x01 Option1

0x72 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable

(Option3)*30x01 FW10 (VIDEO, S-VIDEO) BNC

0x02 FW11 (BNC)

0x03 Reserved

0x04 FW31/32

0x05 FW50 (RGB)

0x06 FW20 (UART +CTRL-S)

0x07 FW13 (COMPONENT) RCA

0x08 FW15 (HDMI x 2)

0x09 FW16 (Digital x 1)

0x0A Reserved

0x0B Reserved

0x0C Reserved

0x0D Reserved

0x0E Reserved

0x0F Not Connect (Continued)

Otros manuales para FWD-50PX3 - 50" Plasma Panel

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Televisor de pantalla plana de Sony

Sony

Sony KDL-46HX800 - 46" Bravia Hx800 Led Backlit Lcd... Manual de usuario

Sony

Sony SS-SP50FW Guía del usuario

Sony

Sony BRAVIA 4-114-592-11(1) Manual de usuario

Sony

Sony KDE-42XBR950 - 42" Xbr Plasma Wega™ Integrated... Instrucciones de uso

Sony

Sony KLV-L32MRX1 Manual de usuario

Sony

Sony FD TRINITRON WEGA KV-13FM12 Guía del usuario

Sony

Sony BRAVIA 4-136-111-12(1) Manual de usuario

Sony

Sony KZ-32TS1E Manual de usuario

Sony

Sony KDL-52EX700 - Bravia Ex Series Lcd... Manual de usuario

Sony

Sony KDF-42WE655 - 42" Grand Wega™ Integrated Lcd Rear Projection... Manual de usuario

Sony

Sony WEGA KE-37XS910 Manual de usuario

Sony

Sony WEGA KE-37XS910 Instrucciones de uso

Sony

Sony Trinitron KV-20M42 Guía del usuario

Sony

Sony Bravia KDL-55W802A Manual de usuario

Sony

Sony KDL-32EX400 - Bravia Ex Series Lcd... Manual de usuario

Sony

Sony WEGA KLV-S23A10 Manual de usuario

Sony

Sony SS-SP50FW Manual de usuario

Sony

Sony BRAVIA KDL-40X4500 Manual de usuario

Sony

Sony WEGA KZ 42TS1 Manual de usuario

Sony

Sony PFM-42X1S Manual de usuario

Sony

Sony KDL-40D340 Manual de usuario

Sony

Sony KZ-32TS1U Manual de usuario

Sony

Sony KDL-40WL140 - Bravia Lcd Television Manual de usuario

Sony

Sony Bravia KDL-48W600B Manual de usuario

Manuales populares de Televisor de pantalla plana de otras marcas

Samsung

Samsung LT-P326W Manual de instrucciones

Philips

Philips 32PFL7602D - annexe 1 Manual de usuario

Philips

Philips 42PF7321 Manual de usuario

JVC

JVC LT-26DX7BFN Manual de usuario

Samsung

Samsung CT2Z45 Manual de usuario

Philips

Philips Match Line 29PT9006/12 Manual de usuario

Samsung

Samsung LNR1550X Manual de usuario

Philips

Philips 37PFL5522D - annexe 2 Manual de usuario

Westinghouse

Westinghouse TX-42F970Z Manual de usuario

Philips

Philips 32PFL5332S Manual de usuario

Philips

Philips 40PFL5705D Manual de usuario

Toshiba

Toshiba 32BV500B Manual de usuario

Philips

Philips MathLine 32PW9765 Manual de usuario

Philips

Philips MatchLine FlatTV 50PF9965 Manual de usuario

Samsung

Samsung Smart TV UN55D6000 Guía

RCA

RCA MR53R400 Manual de usuario

Philips

Philips 28PW8818/12 Manual de usuario

JVC

JVC GGT0362-001A-H Manual de usuario