Sony FIU-710 Puppy Manual de usuario

Page 2 Training Your Puppy®Unit

Training Your Puppy®Unit

A Guide to Installing and Using Your Sony FIU-710

Fingerprint Identity Token with I/O Software’s

SecureSuite®

XS Workstation Software

Training Your Puppy®Unit Page 3

Sony Media & Application Solutions

1 Sony Drive

Park Ridge, NJ 07656

www.sony.com/puppy

and the Puppy logo are trademarks of Sony. SecureSuite XS, SecureLogon, SecureLaunch, SecureFolder, and SecureSession are

products and trademarks of I/O Software, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation.

Adobe and Acrobat are trademarks of Adobe, Inc. Other trademarks are property of their respective owners.

This product may have a possibility (of less than 0.1% according to our measurements) of granting access to persons other than

those who have registered their fingerprints. In no event shall our corporation or our representatives be liable for any incidental,

consequential, or special loss arising from granting an access to persons from other than those who have registered their

fingerprints. In no event shall our corporation or our representatives be liable for any incidental, consequential or special loss

arising from any use, defect, malfunction, or fault of this product.

When sending the fingerprint data via a communication line or storing such data in a computer, sufficient security control is

required to avoid abuse of the data.

Page 4 Training Your Puppy®Unit

Introduction

Thanks for purchasing (shall we say adopting?) a Sony Puppy® fingerprint identity token. We

think you’ll find it to be easy-to-use and a convenient tool in your day-to-day interactions with

your computer. Just think…you won’t need to worry about passwords any more! And you can

be assured that your fingerprints are protected, as they are being matched and processed on the

fingerprint unit sitting on your desk.

This handy guide will assist you in setting up, using, and maintaining your Puppy unit to obtain

the best results. Note that this guide is set up in several sections:

• Section 1: You and Your Puppy Fingerprint Identity Token provides general advice for

using the Puppy unit, including connection and finger placement.

• Section 2: Installing the Software is a step-by-step walkthrough for SecureSuite® XS

Workstation installation.

• Section 3: Enrolling Your Fingerprints on the Puppy Device discusses the registration of

your fingerprints, as well as specific usage, settings, and troubleshooting for the Puppy

unit.

• Section 4: Using SecureSuite XS Workstation shows you how to easily logon to your PC,

replace your passwords, and control access to your PC and applications.

• Section 5: Uninstalling the Puppy Device and SecureSuite XS Workstation Software

describes how to remove the software and hardware from your PC.

• Section 6: Release Notes covers specific limitations or issues imposed by the Puppy

device and associated software.

• Section 7: Frequently Asked Questions (FAQ) lists a number of common questions and

answers regarding installation and use of the FIU-710 device and SecureSuite XS

Workstation software.

• Section 8: Who to Contact? provides contact information and websites for additional

information, technical support, and software updates.

Throughout this guide, you will see text and headings in blue. This indicates an important notice

that you will need to pay special attention to.

For specific questions regarding advanced settings and configuration of the SecureSuite XS

Workstation software package, please be sure to refer to the SecureSuite XS Workstation

Guide on the enclosed CD.*

*This guide and the SecureSuite XS Workstation Guide are provided in Adobe® Acrobat® format on the CD. If

you do not already have the Adobe Acrobat® Reader® application installed, you can download the free Acrobat

Reader at www.adobe.com.

Training Your Puppy®Unit Page 5

Section 1: You and Your Puppy® Fingerprint Identity Token

If you follow some general guidelines, you will be quite happy with the performance and

capabilities of your Puppy unit.

The Unit

The FIU-710 Puppy fingerprint identity token is designed to maximize user

convenience, security, and privacy, and was Sony’s first product to

incorporate both new silicon chip fingerprint sensing and built-in PKI

encryption functions. The FIU-710 unit is unique in the industry with its

ability to scan, store, and match fingerprints entirely on-board the device.

The fingerprint sensor is located underneath the green ‘shutter,’ which

slides up into the unit when you need to scan your fingerprint. The Puppy

device offers robust fingerprint imaging technology based on a technique

known as capacitance, which digitally reads the fingerprint without leaving

ink residue on your finger. Capacitance sensors cannot be fooled by paper

copies and do not require cleaning.

Connections

Sony’s Puppy fingerprint identity units connect to your Windows® 2000/XP operating system-

equipped PC with a USB connector. Please be sure to connect the Puppy device directly to

your PC’s USB port or to a powered*USB hub when prompted during installation. The

Puppy units will not be recognized if connected to a ‘self-powered’ or unpowered hub, and your

PC may become unstable.

The cord provided with the FIU-710 unit is perfect for laptop users, but may be a bit short for

desktop users. A USB extension cord is perfectly acceptable for use.**

You should be able to unplug the Puppy unit at any time, though if you do unplug it when it is

required for a fingerprint check, you could get an error. Simply plug the Puppy unit’s USB cord

back in, and provide your fingerprint as requested. Never unplug your Puppy unit during

fingerprint enrollment.

Fingerprints

Puppy units use highly robust sensing technology to take images of your fingerprints. However,

there are instances where the units may have some difficulty reading your fingerprint. Here are

some things you can do to avoid this situation!

*Connected to an AC adapter.

** You can use a standard male-female USB extension cord or cable made specifically for a 4-pin Mini-B plug, like

that on the top of the FIU-710. For example, Belkin Part Nos. F3U139b06 and F3U139b10.

Page 6 Training Your Puppy®Unit

1. The Puppy® unit reads the patterns of ridges and

valleys on the portion of your finger between the tip

and the first bend in your finger. Do not simply put the

tip of your finger on the sensor and hope for the unit to

detect it! And don’t turn your finger to the right or the

left, or place it upside down… use the finger guide on

the device to judge correct finger placement. Slide the

green shutter up first, and then place your finger

flat and comfortably resting entirely on the sensor

surface, so that it touches the metal plate around

the sensor itself. The tip of your finger should be

resting on the silver latch of the shutter. See the

images on this page for reference.

2. Be comfortable! Don’t try to use a finger that causes

your hand to be at an uncomfortable angle to your

desktop. Enroll and use the finger that’s most

convenient and most comfortable.

3. Always be sure to register at least

two fingers when setting up a user.

This way, if you’ve hurt your finger

and have a bandage on it, you still

have a ‘backup’ finger.

4. During enrollment (registration),

do your best to provide consistent

finger placement: THIS IS

CRITICAL. Good enrollment

enables the unit to provide the best

matching possible during your daily

use of the device, and thus this

process is one of the most important

steps in setting up your Puppy unit.

Don’t rush it!

5. If you typically have dry skin, the Puppy unit may have difficulty reading your finger.

Try touching your finger to your forehead or the side of your nose and then placing your

finger on the unit. The oils will help the sensor to correctly read the ridges and valleys of

your fingerprint.

6. If you typically have very moist skin or tend to perspire a lot, the Puppy unit may have

difficulty reading your finger. Try rubbing your finger on your slacks or sleeve and then

place your finger on the unit.

Training Your Puppy®Unit Page 7

Section 2: Installing the Software

Minimum System Requirements for I/O Software’s SecureSuite® XS Workstation

Authentication Software

• Microsoft® Windows® 2000 SP1 or

• Microsoft Windows XP Home Edition or Professional operating system

• Pentium® III-450 processor or equivalent

• 128 MB RAM

• 30 MB of free hard disk space

• Communication protocol, i.e. TCP/IP installed

• Microsoft Internet Explorer 4.x

Installation

IMPORTANT: You must be an administrator or have administrative rights on your

computer in order to install the SecureSuite XS Workstation software.

IMPORTANT: If you logon to a domain and are a domain user, SecureSuite XS

Workstation will not allow you to logon using the Puppy® device without SecureSuite XS

Server present on the domain (you can still logon with a password). In order to use this

software, you will need to have a local machine account.

IMPORTANT: Prior to running the installer, please verify that you have at least one network

client installed on the target system. If you are able to access the Internet or a network, you have

a network client. This can be verified by viewing the properties of any available connection in

Network Neighborhood or My Network Places by right-clicking the connection icon and

selecting Properties. You should see Client for Microsoft Networks (or something similar).*

Before installing SecureSuite XS Workstation, close all applications and turn off your virus

scanning and detection software.

1. Insert the SecureSuite XS Workstation CD into your CD-ROM drive. Wait for the

installation to start automatically.

2. If the software does not auto-initiate:

• Select Start from the taskbar and then click Run.

• Type D:\Setup.exe (where D is the drive letter for your CD-ROM drive or other

source media) and follow the onscreen instructions to begin the installation

process.

3. Follow the onscreen prompts. When the installation program asks for your Product

License Key, enter the code printed on the label attached to the CD envelope.

*If the Client is not present, click the Install or Add button, then select Client and press OK. The list of available

clients will then be available. We highly recommend that you select Client for Microsoft Networks. If no

connection is available or established, please contact Sony or your administrator.

Page 8 Training Your Puppy®Unit

4. Connect your FIU710 Puppy® unit when prompted to do so.

5. Restart your computer when prompted. Note that it may take several minutes at this

first restart for the software to finish the installation process. Your screen may look

blank, though your mouse cursor will be able to move. Do not shut off your

computer. Please wait for the logon prompt to appear.

You will enroll your fingerprints after restart; please read Section 3 for more details.

Training Your Puppy®Unit Page 9

Section 3: Enrolling Your Fingerprints on the Puppy® Device

SecureSuite® XS Workstation and the FIU-710 Puppy Unit

The FIU-710 fingerprint identity token scans, stores, and matches fingerprints on-board the

device. This means that the Puppy unit is tied to the users that are enrolled within it. Each FIU-

710 device can hold a limited number of fingerprints (a family or small workgroup, for

example), or alternatively, each device can be assigned to an individual user. You can transport

the unit between SecureSuite XS Workstation-enabled client PCs in a client/server environment

only. For more on this, please refer to the SecureSuite XS Server Guide and documentation.

First-time Enrollment

IMPORTANT: Only five distinct users can use their fingerprints to access the PC. These

fingerprint users can enroll as many fingerprints as they wish. However, other users on the PC

will need to use a password-only logon.*

When you are setting up a new user, you must enter a password for the user, even if the

user will not use the password method, as Windows® interprets this user account as not

requiring security. If you are working with an existing user, you will probably already have a

password, and will not need to enter a new one.

Also, when creating a new user, be sure not to set ‘Need to Change Password at Next

Logon’ and then choose only fingerprint authentication for that user (no password). This

will cause an error and may result in Windows becoming inoperable. Set the former command

first, and then, once the new password is set, make the user a fingerprint-only user (see step 9

below).

To enroll an existing user with the FIU-710 fingerprint identity token:

1. On your first restart after installing SecureSuiteXS Workstation, depending on your

operating system, you will see the following:

*Additional user licenses are available. Contact Sony for more details.

Page 10 Training Your Puppy®Unit

• If you are an administrator, you will see a dialog box containing a Manage Users tab.

You can click on the Manage Users button, or from the Start menu, select Programs,

SecureSuite, and click SecureSuite User Manager, or right-click SecureSuite icon on the

system tray and click SecureSuite User Manager. Start with Step 2.

• If you are not an administrator, you will see a dialog box containing a My

SecureSuite Settings tab. You can click on this button, or from the Start menu,

select Programs, SecureSuite, and click My SecureSuite Settings, or right-click

SecureSuite icon on the system tray and click My SecureSuite Settings. Go to Step 3.

• If you are running a Windows XP Home Edition system, you will be prompted with

an Auto-Enroll dialog box, asking if you would like to add a new method. Click OK,

and then follow the directions below in Step 3.

Tabla de contenidos

Otros manuales de Accesorios de computadora de Sony

Sony

Sony VAIO PCGA-PRGT1 Manual de usuario

Sony

Sony Vaio PCGA-PRGR2 Manual de usuario

Sony

Sony Vaio VGP-PRFS10V Manual de usuario

Sony

Sony LocationFree LF-PK1 Manual de usuario

Sony

Sony Vaio VGP-PRFS1 Manual de usuario

Sony

Sony USM32U2 Manual de usuario

Sony

Sony MicroVault USM1GH Manual de usuario

Sony

Sony DECR-1000 A Manual de usuario

Sony

Sony LocationFree LF-B20 Manual de usuario

Sony

Sony LF-X1, LF-X5 Manual de usuario

Sony

Sony MicroVault USM1GH Manual de instrucciones de instalación

Sony

Sony USM1GEX Manual de usuario

Sony

Sony Vaio LocationFree LF-V30 Manual de usuario

Sony

Sony USM128B Manual de usuario

Sony

Sony LF-X1, LF-X5 Manual de instrucciones

Sony

Sony SFD200S-BP Manual de usuario

Sony

Sony LocationFree LF-B20 Manual de servicio

Sony

Sony VAIO VGP-PRA1 Manual de usuario

Sony

Sony Vaio LocationFree LF-V30 Manual de usuario

Sony

Sony VAIO PCGA -PRV1 Manual de usuario

Sony

Sony Vaio LocationFree LF-V30 Manual de usuario

Sony

Sony LF-X1, LF-X5 Manual de usuario

Sony

Sony VAIO PCGA-PRZ1 Manual de usuario

Sony

Sony BW-F101 Professionnal Disc for Data Drive Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas

Motorola

Motorola ATRIX Manual de usuario

HP USB Media Docking Station Manual de usuario

Cherry

Cherry B.UNLIMITED 3.0 Manual de usuario

Logitech

Logitech IO2 Manual de usuario

ARM

ARM DSTREAM-ST Manual de usuario

Bartec

Bartec TC 7 Series Manual de usuario

Philips

Philips SPC3540 Manual de usuario

Logitech

Logitech mk220 Manual de usuario

SilverStone

SilverStone LC02 Manual de usuario

Flexispot

Flexispot ML2B Manual de usuario

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manual de usuario

Adam Equipment

Adam Equipment RS-485 Manual de usuario

Vivo

Vivo MOUNT-KB05-4DW Manual de usuario

Kvaser

Kvaser Memorator Professional Manual de usuario

DRC

DRC D-Imaging Manual de usuario

Sven

Sven Base 305 сombo Manual de usuario

Hama

Hama 108310 Manual de usuario

SpeechWare

SpeechWare FlexyMike FMK03 Manual de usuario