Sony Ericsson Z530c Manual de usuario

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB

Installation Instruction, Electrical

Applicable for Z530c and Z530i

Contents

General.............................................................................................................................2

Go/No Go Testing............................................................................................................2

2.1

Test Set-Up Diagram.........................................................................................2

2.2

Hardware...........................................................................................................3

2.3

Software.............................................................................................................4

Calibration.......................................................................................................................5

3.1

Calibration Set-Up Diagram..............................................................................5

3.2

Hardware...........................................................................................................5

3.3

Software.............................................................................................................7

Power Supply and Jumper Cables (optional)...............................................................8

Lead-Free Electrical Repair...........................................................................................8

Revision History..............................................................................................................9

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 2(9)

1General

The Electrical Installation Instructions describes the procedures for installing all of the hardware

and software needed to perform testing, calibration, and repair activities at an Electrical level for

the Sony Ericsson products specified.

2Go/No Go Testing

There are two options available for making an RF connection to the handset during the Go No/Go

test. One option is to use an RF Fixture (Conducted) and the other option is to use a Coupler

(Radiated).

2.1 Test Set-Up Diagram

All test hardware necessary for this test set up is documented in the Electrical Equipment List

with designated position numbers (POS).

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 3(9)

2.2 Hardware

2.2.1 Computer (SERPOnly)

Ensure the computer (POS-96) is installed and configured correctly according to the instructions

supplied by the manufacturer.

2.2.2 Test Instrument

The test instrument (POS-76) used must be a Sony Ericsson approved instrument with all

required software and hardware options installed. Refer to the Z530 Equipment List, Electrical

for the list of approved test instruments.

The test instrument installation and operation should be in accordance with the manufacturer’s

instructions.

2.2.3 GPIB Card and Cable (SERP Only)

1. Install the GPIB card (POS-83) in the computer according to the instructions supplied by the

manufacturer.

2. Use the GPIB cable (POS-84) to connect the GPIB card (POS-83) to the test instrument

(POS-76).

2.2.4 RF Cable

1. Connect the RF Cable’s (POS-51) N-type connector to the RF port of the Test Instrument

(POS-76).

2.2.5 RF Probe Assembly (Conducted Test Method)

1. Connect the RF Probe Assembly (POS-62) to the RF cable’s (POS-51) SMA type connector.

2.2.6 Battery Eliminator, Jumper cables and Power Supply (optional)

Refer to Section 4 of this document for installation instructions for the Power Supply.

NOTE! It is preferred that a standard fully charged battery be used to power the phone

during the GNG test. However, a second option is to use the Battery Eliminator

(Dummy Battery) with a power supply that meets the requirements documented in

the Electrical Equipment List.

2.2.7 RF Shield Box (Radiated Test Method)

1. Connect the RF adapter (POS-110) to the RF shield box (POS-91).

2. Connect the RF cable’s (POS-51) SMA type connector to the RF adapter (POS-110).

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 4(9)

2.3 Software

2.3.1 Willtek 420x Go/No-Go Test Script

An approved Sony Ericsson Test Script must be installed in the Test Instrument. The Willtek

420x script can be downloaded from CSPN. The Test Script is located on CSPN under Repair

Instructions / Standard. You can also “Search the Archives” on CSPN using reference number

10274-33673 for more details about the script.

The FEA number for the 420x test script is 11/03162-FEA 209 544/701 x when using the R&S

Coupler or the RF Fixture.

NOTE! The “x” in the FEA number refers to the revision of the Test Script. Ensure the

latest revision script posted to CSPN is installed.

Install the Test Script according to the Instrument Manufacturer’s Instructions.

2.3.2 SERPGo/No Go Test Script

SERP stands for “Sony Ericsson Repair Platform”. It is an application used for testing,

calibrating and repairing Sony Ericsson mobile phones.

1. Download the latest revision of the SERP application from CSPN (Repair

Instructions/Standard/SERP Install Package) or through the use of the SERP Online

Update Tool (OUT).

2. Unzip the file and open the file “SERP_Installation.doc” for installation instructions.

3. After SERP is installed a file titled “SERPINFO.htm” will be placed on the Windows

Desktop. This file contains numerous documents including:

•SERP Users Manual – This document contains system requirements, release notes, fault

reporting instructions, supported test instruments, installation procedures and detailed

operating instructions.

•SERP Troubleshooting Guide – This document contains a few troubleshooting steps that

should be reviewed before reporting issues to Sony Ericsson.

•SERP Trouble Report Form – This form should be filled out when reporting SERP issues

to the regional support team.

•SERP OUT Quick Guide – This document contains system requirements, registration

information and general user guidelines for the OUT application.

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 5(9)

3Calibration

3.1 Calibration Set-Up Diagram

3.2 Hardware

3.2.1 Computer

Ensure the computer (POS-96) is installed and configured correctly according to the instructions

supplied by the manufacturer.

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 6(9)

3.2.2 Sony Ericsson Programming Interface – SEPI

The Sony Ericsson Programming Interface (SEPI) (9) is delivered with the necessary software

and instructions for installation.

3.2.3 Sony Ericsson Programming Interface (SEPI) Cable

The Sony Ericsson Programming Interface Cable (10) is the interface between the Sony Ericsson

Programming Interface (SEPI) (9) and the phone.

1. Connect this cable between the Sony Ericsson Programming Interface (SEPI) and the phone.

3.2.4 Battery Charger

A battery charger must be connected to the Sony Ericsson Programming Interface Cable during

calibration.

1. Connect the plug of the battery charger (POS-27) into the plug of the Sony Ericsson

Programming Interface Cable (POS-10).

2. Ensure the battery charger (POS-27) is connected to the line voltage.

3.2.5 USB cable

The USB A-B Plug-Plug cable (43) is the interface between the computer and the Sony Ericsson

Programming Interface.

1. Connect this cable between the Sony Ericsson Programming Interface (SEPI) (9) and the

computer (96).

3.2.6 Test Instrument

The test instrument (POS-76) used for SERP must be a Sony Ericsson approved instrument with

all required software and hardware options installed. Refer to the Z530 Equipment List, Electrical

for the list of approved test instruments.

The test instrument installation and operation should be in accordance with the manufacturer’s

instructions.

3.2.7 GPIB Card and Cable

1. Install the GPIB card (POS-83) in the computer according to the instructions supplied by the

manufacturer.

2. Use the GPIB cable (POS-84) to connect the GPIB card (POS-83) to the test instrument

(POS-76).

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 7(9)

3.2.8 RF Cable

Connect the RF Cable’s (POS-51) N-type connector to the RF port of the Test Instrument (POS-

76).

3.2.9 RF Probe Assembly

Connect the RF Probe Assembly (POS-62) to the RF cable’s (POS-51) SMA type connector.

3.2.10 Battery Eliminator, Jumper cables and Power Supply (optional)

Refer to Section 4 of this document for installation instructions.

NOTE! It is preferred that a standard fully charged battery be used to power the phone

during the calibration routine. However, a second option is to use the battery

eliminator (dummy battery) with a power supply that meets the requirements

documented in the Electrical Equipment List.

3.2.11 Printer (optional)

Install the printer (POS-109) according to the instructions supplied by the manufacturer.

3.3 Software

3.3.1 SERPCalibration Routines

SERP stands for “Sony Ericsson Repair Platform”. It is an application used for testing,

calibrating and repairing Sony Ericsson mobile phones.

4. Download the latest revision of the SERP application from CSPN (Repair

Instructions/Standard/SERP Install Package) or through the use of the SERP Online

Update Tool (OUT).

5. Unzip the file and open the file “SERP_Installation.doc” for installation instructions.

6. After SERP is installed a file titled “SERPINFO.htm” will be placed on the Windows

Desktop. This file contains numerous documents including:

•SERP Users Manual – This document contains system requirements, release notes, fault

reporting instructions, supported test instruments, installation procedures and detailed

operating instructions.

•SERP Troubleshooting Guide – This document contains a few troubleshooting steps that

should be reviewed before reporting issues to Sony Ericsson.

•SERP Trouble Report Form – This form should be filled out when reporting SERP issues

to the regional support team.

•SERP OUT Quick Guide – This document contains system requirements, registration

information and general user guidelines for the OUT application.

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 8(9)

4Power Supply and Jumper Cables (optional)

1. Install the power supply (POS-77) according to the manufacturer’s instructions.

2. Connect the jumper cables to the power supply’s (POS-77) output terminals. Red (POS-88) to

the positive output terminal and black (POS-89) to the negative output terminal.

3. Connect the banana plugs of the red and black jumper cables to the battery eliminator’s

(POS-52) red and black connectors.

4. Set the output of the Power Supply as follows:

•Voltage: 3.8Vdc

•Current: 2.0 amps

5Lead-Free Electrical Repair

This product is manufactured with lead-free solder and lead-free components. During electrical

repair, it is critical to make sure that no lead is introduced into the product. For this reason,

certain repair materials and equipment must be designated as lead-free and labelled accordingly.

A lead-free work area must be setup that is completely separated from work areas that are used to

make leaded repairs. The lead-free work area must also be clearly labelled as shown in the figure

below. Certain items must be designated for lead-free work only. Some of the items that need to

be clearly labelled in this way are listed in the table below. Note that any item that contacts the

solder must be labelled and used for lead-free work only.

Soldering Tips Wicking Tape Tip Cleaner (steel wool)

Solder Tip Tinner Soldering Iron

Installation Instruction, Electrical

1/000 21-2/FEA 209 544/103 A

Sony Ericsson Mobile Communications AB 9(9)

Because of cost and space limitations, some repair centers may not be able to assign a full bench

to lead-free repairs. In this case, both lead-free and leaded repair setups can share the same

bench, but they must be clearly marked with signs and separated by a physical divider. In the

figure below, the large hot air device functions as the divider.

6Revision History

Rev. Date Changes / Comments

A 2006-03-23 Initial Release

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono móvil de Sony Ericsson

Sony Ericsson

Sony Ericsson Z520i Manual de usuario

Sony Ericsson

Sony Ericsson K500 Series Manual de usuario

Sony Ericsson

Sony Ericsson CYBER-SHOT C510 Manual de usuario

Sony Ericsson

Sony Ericsson Walkman W810i Manual de usuario

Sony Ericsson

Sony Ericsson K810i Cyber-shot Manual de usuario

Sony Ericsson

Sony Ericsson Aino Manual de usuario

Sony Ericsson

Sony Ericsson P1i Manual de usuario

Sony Ericsson

Sony Ericsson Jalou Manual de usuario

Sony Ericsson

Sony Ericsson W41S Guía de instalación

Sony Ericsson

Sony Ericsson T630 Manual de usuario

Sony Ericsson

Sony Ericsson Cyber-shot C905 Manual de usuario

Sony Ericsson

Sony Ericsson walkman premier3 Manual de usuario

Sony Ericsson

Sony Ericsson T610 Manual

Sony Ericsson

Sony Ericsson Z750a Manual de usuario

Sony Ericsson

Sony Ericsson G700c Manual de usuario

Sony Ericsson

Sony Ericsson T202 Manual de usuario

Sony Ericsson

Sony Ericsson R306a Manual de usuario

Sony Ericsson

Sony Ericsson Z770i Manual de usuario

Sony Ericsson

Sony Ericsson Walkman W705a Manual de usuario

Sony Ericsson

Sony Ericsson K608i Manual de usuario

Sony Ericsson

Sony Ericsson Walkman W910i Manual de usuario

Sony Ericsson

Sony Ericsson Mix Walkman phone Manual de servicio

Sony Ericsson

Sony Ericsson Z520a Manual de usuario

Sony Ericsson

Sony Ericsson T200 T200 T200 Manual de usuario

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LG LM-X420QN Manual de usuario

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

LG LM-K420EMW Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario