SOMFY IRS 300 Manual de usuario

INSTALLATIONguide

General description :

The IRS 300 is an infra-red remote control system.

It is a control system designed for controlling all types of

interior blinds (exept for curtains and vertical blinds),

line.

It is capable of controlling eight different blinds individually or

as a group and has many sophisticated functions.

IRS 300 INFRARED RECEIVER

Characteristics :

Technical data :

Nominal supply : 24 Vdc

Minimum supply : 20 Vdc

Maximum supply : 35 Vdc

IP rating : IP00

Working temperature : 0°C to 50°C

Output relay : 3A

Housing colour/material : White/ABS

Net weight : 65g

Dimensions : 76 x 50 x 32mm

In compliance with the requirement.

OPTIONS -

IRT 103 individual control function.

IRT 803 multi-channel remote control with individual

or master control functions (one to eight blinds).

WARNING! : The IRT 803 is the sole programming

tool for the IRS 300.

Impulse switch connection for use without remote

control (individual or master control).

The IRS 300 is compatible with the IRT 103 & IRT 803

infrared transmitters.

The IRS 300 is initially

configured to operate with

the IRT103 transmitter or

the IRT 803 without a

channel selected.

PROG.

IRT 803

1 ➟8 1 ➟45➟8

24 Vdc

D C Motors D C Motors

24 Vdc

Individual Control

IRS 300 IRS 300

General Control

Installation :

Mounting :

The IRS 300 has to be installed indoor.

1. Drill a hole in the wall at the desired location using a 5mm drill bit

(depth 25mm) and insert the supplied raw plug.

2. Place the screw supplied into the securing hole on the face of the

IRS 300 and feed into the raw plug.

3. Fix the IRS 300 unit by securing the screw.

SCREW

IRS 300

WALL

RAW PLUG

IRT 103 - To tilt the slats, press and hold one of the corresponding buttons (up or down).

To raise or lower the blind, momentarily press the corresponding button (up or down).

To stop the blind press the stop button.

IMPULSE - To raise or lower the blind, momentarily press the corresponding button (up or down).

SWITCH To stop the blind, press the stop button or push the up and down buttons simultaneously.

IRT 803 - To tilt the slats, press and hold one of the corresponding buttons (up or down).

To raise or lower the blind, momentarily press the corresponding button (up or down).

Point the transmitter at the Infra-red sensor which corresponds to the receiver you wish to control.

If you wish to control one

receiver, press the

corresdponding button of the

channel you have selected.

Then you can control the

receiver by pressing the

buttons : UP , DOWN or

STOP.

1 ➟8 1 ➟45➟8

If you wish to control a

group of receivers, press on

the corresponding button :

1..4 5..8 1..8

Operation :

Wiring :

Enter the programming mode

Press and hold for at least 5 seconds the «prog »button on the IRT 803 transmitter.

The blind concerned, at it alone, will start to tilt up & down quickly.

Warning : If you use the IRT803, it is necessary to « lock » the receivers which are not being programmed by operating

them in either UP or DOWN direction (they will be locked for 3 minutes and it is impossible to enter in the programming

mode by the IRT803). To unlock them, give a STOP order.

PROG.

1 ➟8 1 ➟45➟8

Exit from the programming mode

Press momentarily the «prog »button on the IRT 803 transmitter. The blind stops

tilting.

PROG.

1 ➟8 1 ➟45➟8

Important : Carry out this operation as near as possible to the receiver of the blind that you wish to program.

PROG.

1 ➟8 1 ➟45➟8

Enter the

programming mode.

The blind starts

tilting up & down.

Press the 8 button.

The blind stops

tilting.

Press the button

Exit the programming

mode by pressing the «

prog »button.

1..8

To cancel and revert back to IRT 103 transmitter operation.

> >

PROG.

1 ➟8 1 ➟45➟8

Enter the

programming mode.

The blind starts

tilting up & down.

Press the 1 button.

The blind stops

tilting.

Press the corresponding

button of the desired

channel (1, 2......8).

How to choose a channel (IRT 803 only):

The channel is now

assigned. The blind will

start tilting up & down

quickly again.

Proceed with another

setting for this blind or

exit the programming

mode.

PROG.

1 ➟8 1 ➟45➟8

Enter the

programming mode.

The blind starts

tilting up & down.

Press the 5 button.

The blind starts tilting

slowly.

To set tilting speed:

Increase speed by pressing up.

Decrease speed by pressing

down.

How to set the tilting speed:

Press the button

to confirm.

The blind starts tilting up

& down quickly again.

Proceed with another

setting for this blind or

exit the programming

mode.

5..8

Programming :

The Blind won’t move

1- Check the battery level of the transmitter.

2- Check the low voltage feed of the IRS 300 (inversion between the + and -).

3- Check if there is a bright light shining on the receiver.

4- Check that you are within the infrared transmission range.

5- Check that you are aiming the transmitter at the receiver correctly.

Up and Down is

reversed when

operating with the

transmitter.

1- Check the motor wiring.

PROG.

1 ➟8 1 ➟45➟8

Enter the

programming mode.

The blind starts

tilting up & down.

Press the 3 button. Let

the blind rise to the full

up position. Press the

down button, (the blind

goes down).

Press the stop button

as soon as the down

position is reached.

How to set the automatic opening of the slats in the down position:

>>>

To change this setting

once it is programmed :

Press the «down »

button. The blind moves

to the down position.

Press and hold the «

up »button until the

desired opening is

reached.

Press the button

to confirm.

The blind starts tilting up

& down quickly again.

Proceed with another

setting for this blind or

exit the programming

mode.

5..8

Press and hold the «

up »button until the

desired opening is

reached.

How to re-program the

automatic opening of the

slats in the down

position.

Press the «prog »

button and start the

operation again.

PROG.

1 ➟8 1 ➟45➟8

Enter the

programming mode.

The blind starts

tilting up & down.

Press the 2 button.

The blind stops tilting.

Press the 1 button. The

blind starts tilting up &

down quickly again.

How to cancel the tilting function? - (Roller - Pleated - Cellular Blind Types).

>> >

PROG.

1 ➟8 1 ➟45➟8

Press the «prog »

button to exit the

programming

mode.

Up and Down is

reversed when

operating with the

impulse type switch.

1- Check the motor wiring.

2- Check the impulse switch wiring.

3- Check the switch wiring on the input connector of the IRS 300.

Manfunctions :

Otros manuales de Mando a distancia de SOMFY

SOMFY

SOMFY Situo 1 RTS Manual de usuario

SOMFY

SOMFY CENTRALIS RECEIVER Manual de usuario

SOMFY

SOMFY Telis Soliris RTS Manual de usuario

SOMFY

SOMFY Oximo RTS Manual de usuario

SOMFY

SOMFY Easy Sun io Manual de usuario

SOMFY

SOMFY INTEO TELIS 1 RTS Manual de usuario

SOMFY

SOMFY Nina io Manual de usuario

SOMFY

SOMFY Situo 1 RTS Instrucciones de funcionamiento y mantenimiento

SOMFY

SOMFY Telis 1 Soliris RTS Pure Manual de usuario

SOMFY

SOMFY inis RT Manual de usuario

SOMFY

SOMFY SITUO RTS Manual de usuario

SOMFY

SOMFY nina Manual de usuario

SOMFY

SOMFY KEYTIS INTERIOR Manual de usuario

SOMFY

SOMFY Telis Composio RTS Manual de usuario

SOMFY

SOMFY Telis 4 Soliris RTS Manual de usuario

SOMFY

SOMFY Situo 1 RTS Guía de instalación

SOMFY

SOMFY Situo 1 io Manual de usuario

SOMFY

SOMFY inteo CENTRALIS RTS Manual de usuario

SOMFY

SOMFY Situo 5 Variation RTS II Manual de usuario

SOMFY

SOMFY Nina Timer io Manual de usuario

SOMFY

SOMFY SITUO 5 io/RTS PURE Manual de usuario

SOMFY

SOMFY Smoove Origin RTS US Manual de usuario

SOMFY

SOMFY Telis 1 Chronis RTS Manual de usuario

SOMFY

SOMFY SITUO 1 VARIATION Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación