SOMFY Axovia multi Manual de usuario

Wing gate hydraulic actuators – Installation instructions

multi

Mechanical assembly

5012073

Table of contents

1Safety instructions

Standard model

6Assembly constraints

Specific / standard kits

2Mechanical kit composition

3Technical characteristics

4Pre-assembly checks

5Assembly process



1Safety instructions

Make sure that the hazardous areas (crushing, shearing,

wedging) between the driven part and the surrounding fixed

parts due to the opening movement of the driven part are

avoided.

Regularly inspect the state of the gate. Those gates in poor

condition should be repaired, reinforced or even changed prior

to installation. Regularly check that the screws and fastenings of

the Axovia's various components are securely tightened.

Maintain a clearance area of 500 mm at the back of each wing

when the gate is completely open.

Do not clean your Axovia with a high-pressure water flow rate

cleaning appliance.

Disconnect your Axovia from any electricity source while carrying

out cleaning operations or other maintenance operations if the

appliance is controlled automatically.

Never allow children to play near moving gates.

Never allow children to play with fixed control devices.

Always place the remote control devices out of reach of children.

Always keep a watch over your gate while it is moving.

Never handle your Axovia while it is energized or with the

battery.

Wear protective goggles during the drilling phases.

2Mechanical kit composition

2221

1Cover key x2

2Cover screw x2

3Guard cover x2

4Motor cover screw x4

5Motor cover x2

6Stop screws + arm x10

7Opening stop x2

8Closing stop x2

9Grommet x2

10 Motor x2

11 Motor/pillar fastening plate x2

12 Fastening stud x4

13 Spacer tube x4

14 Flat washer x4

15 Nut x4

16 Motor arm x2

17 Motor arm / gate arm bush x2

18 Gate arm x2

19 Washer x2

20 Motor arm / gate arm screw x2

21 Gate arm bush x4

22 Long clevis pin for gate arm x2

23 Gate clevis x2

3Technical characteristics

Maximum dimensions of a gate

Hmax. height 2 m

Lmax. width 2 m 50

Pmax. weight 300 Kg

Smax. full surface 4 m2

Scope

146

360

142

620

279

300

245

162

211

258

125

70,5

30,5

36,01

10,5

68,5

54,5

474

General overall dimensions (mm)

Table of

characteristics

Frequency of

manœuvres 40 cycles/day

Automatic obstacle

detector

Complies with the NF EN

60335-2-103 standard

with AX24 cabinet

Operating temperature -15˚C to +55˚C

Thermal protection

Yes by means of the AX24

Protection index IP 54

Motor power supply

outlets 24 VDC

Power per motor 130 W

4Pre-assembly checks

When one of the motor support plate

fastening holes is either in empty

space or near the angle of the pillar,

it is absolutely essential to add a

reinforcement bracket (not

supplied).

For an opening > 90°, the

dimension of the pillar should

be 40 cm; otherwise, you MUST use

a bracket.

Pillar reinforcement bracket

If the gate does not have any wings,

provide for metal backing plates

(e.g. 40x40 mm and 4 mm thick) to

fasten the wing clevis.

For a large wing ( > 2 m ) or in

a windy region, SOMFY

recommends installation of an

electric lock.

Wing brace

5Assembly process

The AM vertical axis gives the

position of the motor/pillar

fastening plate.

B is the distance between the

gudgeon and the AM axis.

B depends on the a opening angle

of the wing:

If αα≤90˚ B = 70 mm min

If αα> 90˚ B = 150 mm

Mark out the AM axis.

Check that the open wing does

not knock against the motor.

Locating axis markout

To be on the safe side, check

distance D: distance

between the AM axis and

the first obstacle on the side

opposite the wing (quoin)

D ≥ 450 mm.

Distance Lshould be

beween 800 mm and

2500 mm.

A < 350 mm

D > 450 mm

800 mm < L < 2500 mm

Required clearance

5Assembly process

Mark out a horizontal axis

(AH) in the middle of the

brace, perpendicular to the

wing's axis of rotation.

Extend this axis onto the

pillar as far as the

intersection with AM.

Gate with no brace: if the

gate has no no brace, place

the motors at approx. 1/3 of

the height of the wings

starting from the ground.

In addition, you will be

required to provide for

brackets for fastening the

clevises (see page 4).

Place the motor/pillar

fastening plate at a distance

of 54 mm above AH.

Mark out the drilling points

and drill them: to improve

adjustment, use the round

holes to make your mark,

drill, then turn the fastening

plate over and fix using the

oblong holes.

Check that the

plate is in a

perfectly

horizontal

position.

Mounting the fastening plate

Mount the fastening

gudgeons on the pillar

fastening plate, screw

them as far as the

thread will go.

2. Slide the spacers

onto the fastening

gudgeons.

3. Position and

fasten the motor.

Check that it is in a perfectly horizontal position:

Mounting the motor on the plate

5Assembly process

Open the top cover using the specific

key.

Unscrew the 2 screws on the bottom

cover and remove the cover.

Remove the opening and closing

stops by taking out the central screw.

Unlock the motor by means of the

button located on the top part of the

motor.

When in unlocked position, the

arms should be manœuvred

slowly so as to avoid any damage

occurring to the motors.

(Padlock closed: arms locked;

padlock open: manual operation).

Unlocking the motor

Do not use a tool in order not to

damage the rings.

Assemble the arms, position the

wing clevis without joining it

completely to the fastening axis.

Assembling the arms

Insert the arm into the slide and fasten it.

Self-forming screw

(there is no thread in the motor arm).

Mounting the arms on the motor

1Put the arms into the closing position

5Assembly process

The wings are in the closed

position, against the

central closing stop.

Unfold the arms in the

direction of the gate,

keeping a distance of

15 cm between the

fastening axis of the arms

and the fold in the arms.

4Fasten the wing clevis

Mark out the centre

distances on the wing.

Remove the arms,

Drill. Fasten the clevis.

3Position the wing clevis

Push the motor arm

flat against the inside

closing stop.

2Mount the lower closing stop

Place the lower closing

stop against the

stationary retainer

(opposite side to the

pillar/motor fastening

plate).

5Mount the upper opening stop

Open the wing

according to the

desired angle.

Place the upper

opening stop

against the

stationary retainer

(pillar/motor

fastening plate

side).

6Block the stops

Make sure that the arms are

perfectly horizontal before

drilling.

5Assembly process

Wiring the 24 VDC motor

Connect the 24 VDC power supply cable to the terminal block.

Pass it through the grommet and fasten it to the pillar.

Re-lock the motor prior to any power-up.

Electrical connection and programming

Refer to the AX24 control cabinet installation instructions.

Outward opening kit

Forgates which open outwards.

Scope, wing characteristics

Short wing arm

+ bent arm

Outward

opening kit

réf : 1216065

100

300

Max. weight (kg)

Max.

width

(m)

1.20 2

Do not open onto the public highway!

Aset of photoelectric cells is highly recommended.

Mounting recommendation:

The motors' connection

is inverted!

The position of the arm

should be exactly the

same as in the drawing.

The motor is

placed as close

as possible to the

edge of the pillar

(dimension B = 0).

Motor arm

Gate arm

Fold the angles

in order to block

the bolts heads.

68 mm

Fastening plate position:

6Specific kits mounting constraints

(Consult us)

6Specific kits mounting constraints

Slope opening kit

Forgates mounted on a slope (maximum 20%).

Scope, wing characteristics

no Slope opening

kit

ref : 1216067

100

300

Max. weight (kg)

Max.

width

(m)

1.20 2

Quoin

Mounting recommendation:

85 mm

The dimension B of installation is identical

to the standard kit (see page 4).

Motor arm

Gate arm

Fold the angles

in order to block

the bolts heads.

For 85mm,

the gate arm

is inclined

For a horizontal arm

closed gate, place at

75mm.

Fastening plate position:

Tabla de contenidos

Otros manuales de Controladores de SOMFY

SOMFY

SOMFY animeo IB+ 1860244 Manual de usuario

SOMFY

SOMFY animeo IB+ 4 AC Motor Controller WM 100-120 V... Manual de usuario

SOMFY

SOMFY animeo WM Manual de usuario

SOMFY

SOMFY animeo IB+ 2 AC Manual de usuario

SOMFY

SOMFY Skitter io Guía del usuario

SOMFY

SOMFY animeo KNX 4 DC 2 A Manual de usuario

SOMFY

SOMFY Smoove UNO io Manual de usuario

SOMFY

SOMFY animeo IB + 1822064 Manual de usuario

SOMFY

SOMFY CONTROL BOX 3S RTS Manual de usuario

SOMFY

SOMFY animeo KNX Master Control W2 Manual de usuario

SOMFY

SOMFY animeo LON RTS Module 433 MHz WM Manual de usuario

SOMFY

SOMFY animeo KNX 1860252 Manual de usuario

SOMFY

SOMFY Animeo Series Manual de usuario

SOMFY

SOMFY animeo IB+ 1860087 Manual de usuario

SOMFY

SOMFY ZWAVE to RTS INTERFACE Manual de usuario

SOMFY

SOMFY Connect UAI Plus Manual de usuario

SOMFY

SOMFY WISNIOWSKI Metro 800 RTS Manual de usuario

SOMFY

SOMFY animeo WM Manual de usuario

SOMFY

SOMFY Skitter io Manual de usuario

SOMFY

SOMFY INTEO INIS RT Manual de usuario

SOMFY

SOMFY Smoove UNO IB+ Manual de usuario

SOMFY

SOMFY animeo KNX Master Control W2 Manual de usuario

SOMFY

SOMFY animeo 1860116 Manual de usuario

SOMFY

SOMFY Situo 1 RTS Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario