Solinst 102 Instrucciones de funcionamiento y seguridad

Water Level Meter Indicator Light Replacement

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 2)

Model 101/102/102M Mk2

Back of Mk2 Model 101 Water Level Meter Faceplate with

Older Style Light

Push-Release

Fittings

Note: To replace the light in an Mk1 Water Level Meter (yellow circuit

board and tape Molex connection), you will require the Mk2

Circuit Board Assembly (#102977), which includes the light.

Contact Solinst for the repair part and instructions.

Instructions

For Mk2 Water Level Meters (Push-Release Tape Connection)

1. Remove the battery (battery is located inside the reel hub of

a 102M Mini Water Level Meter. Remove the batttery after

Step 2).

2. Unscrew the three screws and remove the faceplate.

3. Press down on the white terminals of the push-release

ﬁttings on the circuit board and pull out to remove the

tape/cable leads.

4. If you have an older style light (leads connected to Sonalert

terminals – see photos below), cut the red and black wires

connected to the light, and push the light out through the

front of the faceplate.

Back of Mk2 Model 101 Water Level Meter Faceplate with

New Style Light

Light

Light Connections

Light

Push-Release

Fittings

5. From the front of the faceplate, use the wrench to unscrew

the nut holding the test button and push the button back

out of the faceplate.

6. Unscrew and remove the two screws holding the circuit

board (and older style light leads) from the Sonalert.

7. Carefully lift the circuit board from the Sonalert so you have

better access to the circuit board.

8. If you have a newer style light, unsolder it from the circuit

board and remove as much of the old solder as possible.

9. If you had an older style light (or the lens needs replacing)

insert the new red lens through the front opening in the

faceplate and secure using the white nut.

10. For a Model 101 or 102 Water Level Meter, insert the

leads of the new light into the two positions labelled “D2”

on the circuit board and solder in place. See photo below.

Back of Mk2 Model 102M Mini Water Level Meter Faceplate

with Older Style Light

Light

Light Connections

Push-Release

Fittings

Light (under

circuit board)

Push-Release

Fittings

Back of Mk2 Model 102M Mini Water Level Meter

Faceplate with New Style Light

Continued overleaf...

Tools and Materials Needed

1. WLM Replacement LED (Light) Assembly (Spare) (#113923)

2. Phillips Screwdriver

3. 10 mm (3/8") Wrench

4. Wire Cutters (if required)

5. Wire Strippers (if required)

6. Solder Wire with Flux

7. Soldering Iron

Printed in Canada

June 5, 2018

(#113922)

(Page 2 of 2)

For further information contact: Solinst Canada Ltd.

Fax: +1 (905) 873-1992; (800) 516-9081 Tel: +1 (905) 873-2255; (800) 661-2023

35 Todd Road, Georgetown, Ontario Canada L7G 4R8

Web Site: www.solinst.com E-mail: [email protected]

11. For a Model 102M Mini Water Level Meter, insert the

leads of the new light into the two positions labelled “D4”

on the circuit board and solder in place (“D4” positions are

located next to “D2” positions). See photo above.

12. Place the circuit board assembly back into position on top

of the Sonalert, ensuring the sides marked +ve and -ve are

lined up with the corresponding terminals on the Sonalert

and the new light seated in the lens.

13. Reinstall the two screws to connect the bare wires from the

circuit board to the terminals on the Sonalert.

14. Insert the test button through the opening in the faceplate,

and secure it in place using the nut.

15. For 101 Water Level Meters, connect the tape to the circuit

board assembly by pressing down on the white terminals

on the circuit board and inserting the tape leads. Release

the terminals and the leads should be secured. The lead on

the bottom of the tape (numbers facing up, may be black

mark on lead) is inserted into the terminal with a white

square below it on the circuit board.

Square

16. For 102 and 102M Water Level Meters, connect the cable

to the circuit board assembly by pressing down on the

white terminals on the circuit board and inserting the leads.

Release the terminals and the leads should be secured.

The positive lead is inserted into the terminal with a white

square below it on the circuit board. (The positive lead has

the pin connected to insulated wire, the negative pin is

connected to the braided wire).

17. Install the battery.

18. With the probe in a glass of tap water, turn the Water Level

Meter to the ‘ON’ position. If the connections are correct

the light will activate. If the light does not activate, check all

connections and the polarity of the battery.

19. Reattach the faceplate to the reel using the three screws.

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de Solinst

Solinst

Solinst 615 ML Manual de usuario

Solinst

Solinst 101 SC2000 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 101 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 107 Mk2 Manual de usuario

Solinst

Solinst 101 P7 Manual de usuario

Solinst

Solinst 101 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 107 Guía

Solinst

Solinst 101D Manual de usuario

Solinst

Solinst 101 Manual de usuario

Solinst

Solinst 104 Manual de usuario

Solinst

Solinst 102 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 101 Manual de usuario

Solinst

Solinst 101B Manual de usuario

Solinst

Solinst 107 Mk2 Manual de usuario

Solinst

Solinst 102M Manual de usuario

Solinst

Solinst LevelSender 5 Manual de usuario

Solinst

Solinst 122M Manual de usuario

Solinst

Solinst Levelogger 3001 Manual de uso y cuidado

Solinst

Solinst 101 P2 Manual de usuario

Solinst

Solinst 122 Manual de usuario

Solinst

Solinst 101 P2 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 401 Manual de usuario

Solinst

Solinst 101 Instrucciones de funcionamiento y seguridad

Solinst

Solinst 101 Instrucciones de funcionamiento y seguridad

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario