Solinst 464 125 psi Guía de configuración

Control Unit Solenoid Valve Cleaning Instructions

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 2)

Model 464 125 psi (sold until January 2016)

Continued on page 2...

Tools and Materials Needed

1. 3/32" Allen Key

2. Small Utility Knife

3. 9/64" Allen Key

4. Cotton swab

5. Distilled water

6. Any suitable plastic adhesive (e.g. silicon)

Hex

Screws

Hex

Screws

3. Remove the panel from the Control Unit and ﬂip it over to

access the Solenoid Valve Assembly.

Panel

4. Use the small utility knife to break any adhesive seal that is

holding the Solenoid connector to the circuit board.

Solenoid Valve

Assembly

5. Carefully, pull to remove the Solenoid connector from the

circuit board.

Solenoid

Connector

Solenoid

Connector

6. Remove the tubing from the three ﬁttings on the Solenoid

Valve Assembly, by pushing on the “grasping ring” on the

ﬁtting (to release tubing) and pulling the tubing out.

Fitting “Grasping Ring”

Fitting “Grasping Rings”

7. Use the 9/46" Allen key to remove the two screws holding

the Solenoid Valve Assembly to the bracket.

Remove

Screws

Instructions

Note: These instructions are for Model 464 125 psi Control Units

sold up until January 2016.

1. Turn the Control Unit off and remove the batteries.

2. Use the 3/32" Allen key to undo the four hex screws on the

sides of the Control Unit.

Printed in Canada

January 22, 2016

(Page 2 of 2)

For further information contact: Solinst Canada Ltd.

Fax: +1 (905) 873-1992; (800) 516-9081 Tel: +1 (905) 873-2255; (800) 661-2023

35 Todd Road, Georgetown, Ontario Canada L7G 4R8

Web Site: www.solinst.com E-mail: [email protected]

8. By hand, unscrew the brass ﬁtting from the Solenoid Valve

Assembly, and pull out to remove the magnetic plunger from

the steel ﬁtting.

9. Inspect the small rubber circular pad on the end of the plunger.

If this pad is damaged, dented, etc., the Solenoid will not

seal properly, therefore you may need a new Solenoid Valve

Assembly. (Contact Solinst). See photo below comparing a

damaged pad to a pad in good condition.

Magnetic

Plunger

®Solinst is a registered trademark of Solinst Canada Ltd.

10.To clean the Assembly, use a cotton swab and distilled water

to clear any debris and dirt from inside the brass ﬁtting, around

the o-ring, steel ﬁtting and from the magnetic plunger.

11.Ensure the o-ring is properly seated inside the brass ﬁtting.

Insert the magnetic plunger back into the Solenoid Valve

Assembly, and screw the brass ﬁtting back onto the Assembly.

12.Mount the Solenoid Valve Assembly to the bracket using the

two screws.

13.Push the tubing into the three ﬁttings. Refer to the photo on

Page 1, to ensure proper connection.

14.Reconnect the Solenoid connector to the circuit board. After

connection, add a small amount of adhesive to the outside of

the connector to help secure it to the circuit board.

15.Place the panel in the Control Unit case and reinstall the four

hex screws.

16.Reinstall the batteries. Test the Control Unit to ensure proper

connections were made and the Solenoid is now functioning.

Steel Fitting

Brass

Fitting

Note: The photo above shows the tubing ﬁttings removed from the

Solenoid Valve Assembly, you do not need to remove these.

O-ring

Magnetic

Plunger

Otros manuales de Unidad de control de Solinst

Solinst

Solinst 464 Mk3 250 psi Manual de uso y cuidado

Solinst

Solinst 464 250 psi Manual de uso y cuidado

Solinst

Solinst 464 Manual de usuario

Solinst

Solinst 464 125 psi Manual de uso y cuidado

Solinst

Solinst 464 250 psi Manual de uso y cuidado

Solinst

Solinst 464 250 psi Guía de configuración

Solinst

Solinst 464 Mk3 Manual de usuario

Solinst

Solinst 464 Instrucciones de funcionamiento

Solinst

Solinst 464 125 psi Manual de uso y cuidado

Solinst

Solinst 464 Mk3 250 psi Manual de uso y cuidado

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario