Setting telephone numbers
The device can be set for up to three telephone numbers to be called or be sent text messages. The procedure for adding numbers
is as follows:
1. Activate the keypad
2. Enter the first string of digits in the format *1 telephone number* (asterisk → digit 1 → telephone number → asterisk).
3. After the last asterisk is pressed, the telephone number is stored. The green LED indicator 1 on the front of the device will
flash three times when the number has been saved successfully. If you make a mistake, repeat the whole procedure.
4. Follow the same procedure to set the second and third numbers (if wanted), except instead of pressing the number 1, press 2,
or 3; e.g. to add a second or third number, 602 123 456, type: *2602123456*
To delete a telephone number, type *N*, where “N”means the order of the number; e.g., if you want to delete the second telephone
number, type the following command: *2*. The green LED indicator 1 will signal that the number has been successfully deleted.
Note: Telephone numbers can be up to 17 digits long and may be entered without a country code. Do not enter numbers for the
police, fire brigade, emergency services or other similar institutions. Enter only numbers of close persons that you can trust.
The device operates as follows. When movement is detected, the 5 second run time to trigger the alarm starts. The sound signal is
then activated for 30 seconds (if enabled). During this time, the device will call all of the set telephone numbers and play the voice
recording. If the SMS function is enabled, the device sends a message with the text “Alarm system triggered!” to all the telephone
numbers.
Note: The device makes three contact attempts. If only one number has been set, the device will dial it 3 times, even if the call is
answered on the first attempt. If two numbers are set, the device will dial the first number, and then, regardless of whether or not
the connection was successful, will dial the second number, and then dial the first one again. If three numbers are set, the device
will dial all three.
Enabling/Disabling the SMS function
The SMS function has been already partially described in the previous section. In addition to alerting that the alarm has been set
off, this function can also alert the user when the battery is low. The procedure to enable/disable this function is as follows:
1. Activate the keypad
2. Press #9# (hash → number 9 → hash)
3. The device confirms that the SMS function has been enabled by emitting a double beep.
4. The function is disabled in the same way. The disabling is confirmed with a single beep.
5. If the battery is low, the text message reads as follows: “GSM Alarm Low Battery!”
Note: The device sends a text message to warn of low battery level in the main unit only. Low batteries in accessories are signalled
by the LED of each accessory. Depleted batteries on accessories are indicated only by the LED on the accessory. An SMS warns
that the batteries will soon need to be changed, not that they are completely depleted. Completely depleted batteries are indicated
by a lit LED.
Silent mode
When silent mode is activated, the device will not sound the alarm when movement is detected, but will immediately start to dial the
pre-set telephone numbers and to send text messages, if the function is enabled. To activate silent mode, proceed as follows:
1. Activate the keypad
2. Press *7* (asterisk → number 7 → asterisk)
3. The device confirms silent mode has been activated by emitting a beep
4. Deactivate the mode the same way. Deactivation is confirmed with a double beep.
Note: Silent mode applies only to the main unit. Additional sirens and other accessories are not affected by silent mode.
Recording a voice message
A custom voice message that will be played during a telephone call can be recorded on the device. To record a voice message,
follow these steps:
1. Activate the keypad
2. Press #1# (hash → number 1 → hash).
3. The LED will light for six seconds, during which you should record your message.
4. If you want to change the message, repeat the procedure above.
The device is now set up and almost ready to use.
