Soleus Air WS1-15E-02 Manual de usuario

V190108

Air conditioner must be upright for 24 hours prior to operating.

This ensures that the compressor will function as intended.

Model

WS1-15E-02 15,000 BTU

WS1-18E-02 18,300 BTU

WS1-24E-02 24,000 BTU

Electronic Window Air Conditioner

Operating Instructions

AIR CONDITIONER

2MF3

File No. SA 12793

Thank you for choosing a Soleus Air Window Air Conditioner. This Owner’s Manual will provide

you with valuable information necessary for the proper care and maintenance of your new product.

Please take a few moments to thoroughly read the instructions and familiarize yourself with all the

operational aspects of your new Soleus Air Window Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the

store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: _____________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

PURCHASE INFORMATION

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a

safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to

all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic

precautions:

 Plug into a grounded 3 prong outlet.

 Do not remove the ground prong.

 Do not use a plug adapter.

 Do not use an extension cord.

 Unplug the air conditioner before servicing.

 Use two or more people to move and install the air

conditioner.

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause death.

All safety messages will directly follow the safety alert symbol and/or the words “DANGER”

or “WARNING.”

All Safety messages alert you of potential hazards, how to reduce the chance of injury, and what

can happen if instructions are not followed correctly.

Failure to immediately follow these in-

structions may cause serious injury or

even death.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the device has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazard if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly.

To test:

1. Plug power cord into wall outlet, the LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs, the LED

light will turn off.

3. Press RESET button to restore power to the unit. Once power is restored, the LED light will turn on.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting recommenda-

tions.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

POWER CORD AND PLUG

RESET

TEST

LED LIGHT

Note: Your unit’s power cord may

differ from the one shown.

PACKAGE CONTENTS

 Window Air Conditioner (1)

 Remote Control (1)

 AAA Battery (2)

 Top Mounting Rail (1)

 Foam Gasket (1)

 Curtain (2)

 Foam Seal for Bottom Rail (1)

 Hardware Bag (1)

 Owner’s Manual (1)

 Weather Insulation Board (2)

 Window Sash Seal (1)

 Window Support Bracket (2)

TOOLS NEEDED

Large Flathead Screwdriver

Tape Measurer

Adjustable Wrench or Pliers

Pencil

Level

Socket Wrenches

Phillips Head Screwdriver

Hardware

(In plastic Bag)

Quantity

Sash Lock

Screw and

Locknut

Flathead Bolt

and Locknut

Sill Angle

Bracket

Curtain Lock

Long Screws

Short Screws

SPECIFICATIONS

 Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

 Power consumption is measured when the fan runs at the highest speed setting.

 These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model WS1-15E-02

Power Supply (Ph/V/Hz) 1/115/60

Rated Cooling Capacity (BTU/h) 15,000

Cooling Power Input (Watts) 1,230

Rated Current Cooling (Amperage) 12

CEER 11.8

Noise Level dB(A) (L/H) 55/59

Airflow CFM (H/L) 411/358

Dehumidifying Capacity 73.9 Pints per day

Product Dimensions (W” x H” x D”) 23.625” x 17.75” x 25.375”

Package Dimensions (W” x H” x D”) 26.125” x 20” x 30.5”

Net/Gross Weight (Lbs) 110/121

Refrigerant Type R-410A

Plug Type NEMA 5-15P

Model WS1-18E-02 WS1-24E-02

Power Supply (Ph/V/Hz) 1/230/60 1/230/60

Rated Cooling Capacity (BTU/h) 18,300 24,000

Cooling Power Input (Watts) 1,530 2,330

Rated Current Cooling (Amperage) 6.7 10.3

CEER 11.8 10.3

Noise Level dB(A) (L/H) 56/61 56/61

Airflow CFM (H/L) 430/370 447/388

Dehumidifying Capacity 82.8 Pints per day 152.4 Pints per day

Product Dimensions (W” x H” x D") 26.375” x 18.625” x 26.625” 26.375” x 18.625” x 26.625”

Package Dimensions (W” x H” x D”) 29.5” x 20.875” X 31.125” 29.5” x 20.875” X 31.125”

Net/Gross Weight (Lbs) 132.27/154.32 141.1/163.1

Refrigerant Type R-410A R-410A

Plug Type

NEMA 6-15P NEMA 6-20P

ELECTRICAL SAFETY

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENATION OF THE MANUFACTURER. SOLEUS N.A. HAS NOT CONDUCTED AN INDEPENDENT TEST TO

VERIFY THE INFORMATION AND SPECIFICATIONS PRESENTED HEREWITHIN.

INSTALLATION

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If a new

electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made to fit

inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the provided screws. If

not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which will keep it from draining properly. To ad-

just for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage (See FIG. 2).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,

or awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

When handling the unit, be careful to avoid cuts from the

sharp metal edges and aluminum fins on the front and rear

coils.

Model WS1-15E-02 WS1-18E-02 / WS1-24E-02

Unit Height 17 3/4" 18 5/8"

Unit Width 23 5/8" 26 3/8"

Min. Window Opening (See FIG 1) 18 3/4" 19 7/8"

Min. Window Width 28 1/8" 30"

Max Window Width 41 3/4" 50 "

18 3/4", / 19 7/8"MIN

18 3/4" / 19 7/8"MIN

FIG.2

FIG.1

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

1. Pull down the front panel and remove the filter (See Fig. 3).

2. Lift the front panel upwards to remove and place to the side.

3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air condi-

tioner (See Fig. 4).

4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet. Remove the ground screw and

save for reinstallation later (See Fig. 5 & 6).

5. Remove the two screws from top of the unit (See Fig. 7). Hold the cabinet while pulling on the base handle, and care-

fully remove the unit.

INSTALLATION

Curtain

Curtain Installation

3. Fasten the curtains to the unit with short screws (Fig.10).

Weather Insulation Board Installation

NOTE: The Weather Insulation Boar d adds an extr a

layer of insulation to keep air from passing through the

sides of the window air conditioner.

1. Using a sharp blade or scissors, slowly cut the

Weather Insulation Board to a size that will fit inside

of the side curtain rails and completely cover the cur-

tain.

2. Once properly sized, remove the backing to expose

the adhesive tape.

3. Place the Weather Insulation Board over the left cur-

tain and firmly press and hold for 5 seconds.

4. Repeat above steps to install the Weather Insulation

Board on right curtain (Fig.11).

Fig. 8

Curtain

Fig. 9

Fig. 10

Fig. 11

Weather Insulation Boards

Fig. 12

Long Screw

Place the Cabinet Inside the Window

1. Set the cabinet in the window so that is centered.

Place the unit so that front edge of the bottom rail

is against the back edge of the sill.

2. Bring the window down so that the front edge of

the top rail is in front of the window. Be sure the

unit is tilting slightly to the outside.

3. Fasten cabinet to window sill using three long

screws. Pre-drill holes if needed. Add the bottom

rail seal over the screws (Fig. 12).

Window

Frame

Top Rail

Bottom Rail

1/4”

1. Attach the top mounting rail to

the unit with short screws (Fig.8).

2. Slide the free end of the curtain into the side panel of the

air conditioner. Do this for each side. The flange for securing

the curtain into the window sill will be facing the room side

when installed (Fig.9).

Top Mounting

Rail

Bottom Rail Seal

INSTALLATION

Install Support Brackets

1. Hold each support bracket flush against the outside of

the window sill. Tighten each bracket to the bottom of

the cabinet as shown below. Mark the brackets at top

lever of the window sill and then remove.

2. Assemble the sill angle brackets to the support brackets

at the marked position as shown above. Hand tighten,

but not all the way for any changes that may need to be

made later during installation.

3. Install the support brackets (with sill angle brackets

attached) to the bottom of the cabinet as shown below.

4. Tighten all 6 bolts securely.

Screw &

Locknuts

Install the Window Lock and Sash Seal

1. Trim the sash seal to fit the width of the window. Insert

the sash seal into space between the upper and lower

sashes.

2. Attach the right angle safety lock as shown below.

Este manual sirve para los siguientes modelos

Otros manuales de Acondicionador de aire de Soleus Air

Soleus Air

Soleus Air SG-WAC-15ESE-C Manual de usuario

Soleus Air

Soleus Air SG-WAC-05SM Manual de usuario

Soleus Air

Soleus Air GH-PAC-10E5 Manual de usuario

Soleus Air

Soleus Air WM1-12E2-01 Manual de usuario

Soleus Air

Soleus Air 3046364 Manual de usuario

Soleus Air

Soleus Air PE2-07R-62 Manual de usuario

Soleus Air

Soleus Air WM1-05M2-01 Manual de usuario

Soleus Air

Soleus Air TTWM1-10-01 Manual de usuario

Soleus Air

Soleus Air PH1-12R-03 Manual de usuario

Soleus Air

Soleus Air MAC-10K Manual de usuario

Soleus Air

Soleus Air SG-WAC-06ESE-C Manual de usuario

Soleus Air

Soleus Air PH3-09R Manual de usuario

Soleus Air

Soleus Air HM1-10-32 Manual de usuario

Soleus Air

Soleus Air PE6-10R-03 Manual de usuario

Soleus Air

Soleus Air KC-45H Hoja de especificaciones

Soleus Air

Soleus Air GM-WAC-25ESE-C Manual de usuario

Soleus Air

Soleus Air GM-PAC-10E2 Manual de usuario

Soleus Air

Soleus Air Air condioner Manual de usuario

Soleus Air

Soleus Air SA-50 Manual de usuario

Soleus Air

Soleus Air KFH-12/KFH-12-1 Manual de usuario

Soleus Air

Soleus Air SG-PTAC-09HPDA Manual de usuario

Soleus Air

Soleus Air MA-9000AH Manual de usuario

Soleus Air

Soleus Air PE8-11R-32 Manual de usuario

Soleus Air

Soleus Air PE7-10R-03 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

McQuay

McQuay MCK020A Manual de usuario

Webasto

Webasto Frigo Top 25 DS Manual de usuario