Congratulations on choosing the SolarGo2’s PWM solar regulator, it is as
tough asyou need it forthe outside lifestyle, and it’sdesigned to work
perfectly with ourrange of 12v leisure solar panels.
This rugged solar regulator will optimally charge a large range of battery
types, including AGM, Gel, Calcium, Wet and all common lithium variants
including LiFePO4, Li-ion and Li+. It contains a host of smart electronics
including reverse polarity protection, short circuit protection, reverse current
protection, overcharge protection and much more.
Please follow the below instructions to get the very best from this product.
If you have any questions not answered in this user manual, please visit the
product page on our website www.solargo2.comfor more FAQs and help.
FEATURES
This in-line solar charger controller is designed with PWM
(pulse width modulated) technology.
Anderson ports are providedforsolar panel and battery connection.
Suitable for 12V systems only.
Suitable forall kinds of 12V solar panels, ina 12V solar system.
Suitable formost rechargeable batteries: Lithium battery (LiFePO4, Li-ion
and Li+.), Lead Acid battery (AGM, Wet, Gel and Calcium).
Built-in high efficiency smart regulation to prevent your battery from being
over or undercharged, optimisesthe battery performance to keepyour
battery permanently fully charged.
Coloured LEDstoeasily indicate the charging status and battery conditions.
Big digital LCD screen displaying battery voltage, charging current,
charging capacity (Amp/hour), battery types, charging percentage, battery
temperature and fault codes.
Waterproof design, suitable for indoor and outdoor use.
Designed according toCE and UKCA standards, EMC, FCC compliance.
WARNING
Explosivegases develop during normal battery operation.
To reduce risk of battery explosion, follow these instructions and
those published by the battery manufacturer.
solar controller during charging operation as batteries may give out
explosive gases
near a lead-acid battery or Lithium battery
water. If acid enters the eye, immediately flush the eye with running cold
water for at least 10 minutes and get medical attention immediately
Rated
current
The cable total length
One-way distance
Solar panel -> Controller -> Battery
< 3M 3-6M 6-9M 9-12M
15Amp 14AWG 12AWG 10AWG 8AWG
Rated
current
The cable total length
One-way distance
Solar panel -> Controller -> Battery
< 10ft 10-20ft 20-30ft 30-40ft
15Amp 14AWG 12AWG 10AWG 8AWG
Unit: Metre
Unit: Feet
OPERATION - LCD DISPLAY
Please check your battery manufacturer’s
specifications to select correct battery
type. The unit provides 6 batterytypes for
selection: LTO, LiFePO4, Gel, AGM, WET
(conventional lead acid), Calcuim battery.
Press ‘batterytype’ button and hold for 3 seconds to go into your battery
type selection mode. The battery type you select will be shown onthe LCD
meter-the default setting is AGM battery. The controller will automatically
Pleasenote - LFP battery shown in LCD indicates Lithium Iron Phosphate
battery, LiFePO4 battery. LTO battery shown in LCD indicates Lithium
Titanium Oxide battery.
Caution -Incorrect battery type setting may damage your battery. When the
controller powers on, the unit will run self-qualify mode and automatically
show below items on LCD before going into charging process.
Self-test starts, digital metersegmentstest
Software version test
Ratedvoltage and current test
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as
below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
battery voltage, charging current, charged capacity (Amp-hour) and battery.
The VOLT / AMP button can be changed at any time during charging process.
The LCD can also be treated as an independent voltage meter.
INSTALLATION
The Solar Controller is mounted as shown below. The easiest way to mount the unit
is to use two small but long self-tappingscrews and mount the unit to aflat surface.
WIRING CONNECTIONS
To protect the battery, we strongly recommend that you place an in-line fuse on the
positive wire on the ‘battery’ circuits as per the wiringdiagram(Fig1). We recommend
a 20A or 30A fuse for the 15A controller (as close to the battery as possible).
Connect the input and output cables by Anderson connectors (supplied) to the output
fromthe solar panel and the input to the battery, please note the correct polarity ie
positive +and negative – for connectionsto the solar panel and the battery.
Wring diagram
Refer tothe below drawing. Please cover the solar panel before connecting the cables.
they are disconnected. Cover the panel(s) with a soft cloth to block all
incoming light during the installation. This will ensure that no damage
is caused to the solar panel or battery if the wires are accidentally
short circuited
controller
is required
Fitting Anderson connectors (supplied)
Anderson connections. We have asimple grid below to help you with this.
The Anderson connections supplied can be soldered or crimped onto the
wire. Please go to our website to see a short video on how to do this. Or
have a look on YouTube asthere are lots of good examples on how to fit this
connection to your cables.
Correct Wire Size
wire needed for each connection. This will also ensure you get the best
performance out of your solar controller. The solar controllershould be
installed as close to the battery as possible. When the connections are
completed, the solar controller will start working automatically.
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
C
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
C
Alternatively Display voltage and FUL when battery is fully charged
V
The VOLT / AMP button can be changed at any time during charging process.
The LCD also can be treated as an independent voltage meter or thermometer.
CHARGING STAGE-
The unit has a 6-stage charging algorithm.
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
(Fig.1)
In-line Fuse
P.3/8
- Rubber mask to protect the Anderson connectors
INSTALLATION-
The Solar Controller is mounted as shown below
The quickest and easiest way to mount the unit is to use the two plastic spacers and self-tapping screws supplied and
mount the unit to a flat surface,
WIRING CONNECTIONS-
To protect the Battery and the Solar Panel, we strongly recommend that you place an inline fuse on the positive wire on
both the “Solar” and “Battery” Circuits. 50A fuse for 40A controller; 40A fuse for 30Acontroller, 30A fuse for 20A controller;
20A fuse for 15A controller (As close to the Battery /Panel as possible)
Connect input and output cables by Anderson connectors to the input solar panel and output battery, please note that
Positive +and Negative –for the correct polarity connection to the solar panel and battery.
Mount screw hole
Mount screw hole
200mm
87.6mm47.8mm
37.7mm
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
P.5/8
--The solar controller is installed to close to the battery as near as possible.
When the connections are completed, the Solar Controller will start working automatically.
OPERATION - LCD DISPLAY-
Please check your battery manufacturer’s specifications to select correct battery type. The unit provides 6 battery types for
selections: LTO, LiFePO4, Gel, AGM, WET (conventional lead acid) battery.
Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection mode, the battery type you
select will be shown on the LCD meter, the default setting is AGM Battery; the controller will automatically memorize your
battery type setting.
LFP battery shown in LCD indicates Lithium Iron Phosphate battery, LiFePO4 battery.
LTO battery shown in LCD indicates Lithium Titanium Oxide battery.
Caution: Incorrect battery type setting may damage your battery.
When the controller powers on, the unit will run self-qualify mode and automatically show below items on LCD before
going into charging process
Self-test starts, digital meter segments test
Software version test
A
Rated voltage and current test
ºC
External battery temperature sensor test (if connected)
Indicates the solar panel connected.
After going into charging process, the LCD displays the charging statues as below:
Press VOLT / AMP button in sequence, the LCD will display in turn with
Battery Voltage, Charging Current, Charged capacity (Amp-hour) and Battery
Temperature (if external temperature sensor connected)
Display in sequence-
ºC
Alternatively Display voltage and FUL when battery is fully charged
Anderson
connectors
Anderson
connectors
30A Fuse
