Solar Speed Wireless 3G router + WiFi Manual de usuario
SOLARspeed
Wireless3Grouter+WiFi
User Guide
Version 2.0 2012.
USER MANUAL
SOLARspeed
3G Router
Chapter 1.
1.1 Introduction.
Thank you for purchasing of SOLARspeed 3G Wireless Router.
SOLARspeed 3G Wireless Router supports WiFi, Ethernet gateway and 3G in one device, and it is espe-
cially designed for small Companies, and Solar Parks.
SOLARspeed 3G Wireless Router offers wireless broadband WAN HSUPA connection with rate up to 7.2Mbps.
On Local area Network (LAN) it supports both the newest IEEE802.11n, IEEE802.11b/g and wire Ethernet
10/100Mbps interface.
The SOLARspeed router integrate one (1) WAN port, one (1) 10/100Mbps LAN port, and a SIM slot for di-
rectly using the 3G SIM card. The 11n WIFI supports rates up to 150Mbps with a NAT firewall which
supports SPI and an easy-to –use web operation interface.
1.2 Overview.
1.2.1 Product Appearance.
Figure1.2.1 3G Wireless-N appearance picture.
1
USER MANUAL
SOLARspeed
3G Router
1.2.2 Physical Details.
1.2.2.1 Front Panel
The SOLARspeed 3G router front panel has a lot of indicator LED,
see the following layout:
Figure1.2.2 the front panel picture
Name State Description
Light on The power is ready and it works
Power Light off The power is off.
Light on The connection is established with the computer or the local area network
through the corresponding LAN port.
Light flash Sending / receiving data
LAN
Light off There is no device linked to the corresponding LAN port
Light on The connection is established with the xDSL Modem/Cable Modem or Ethernet
(for example: Hub, Switch and Router) through the corresponding WAN port.
Light flash Sending/receiving data
WAN
Light off There is no device linked to the corresponding WAN port
Light on The wireless connection is established
Light flash Sending /receiving data
WiFi
Light off The wireless connection is not established
Light on The 3G service is ready.
Light flash Trying to link the 3G network.
3G
Light off The 3G service is not established.
2
USER MANUAL
SOLARspeed
3G Router
1.2.2.2 Rear Panel.
The most ports of SOLARspeed router are on the rear panel.
Please see the following picture:
Figure 1.2.1 the rear panel picture
Instruction of the ports on the rear panel:
3G ANT 3G/WiFi antenna port, used for 3G/WiFi wireless operation and data trans-
mit.
WAN Wide area Network port (RJ45). It is used for connecting the router to the
xDSL Modem/ Cable Modem or Ethernet network device (for example :Hub,
Switch)
LAN Local area Network port (RJ45) . Through this port, you can connect the
router to your PCs and other Ethernet network device (for example: Hub,
Switch).
SIM Card SIM card port
Power Turning on/off the router power.
Reset After the router is power on, press this reset button for five seconds to
reset the router, the router will be restored to factory default settings.
DC (+12VDC) The power plug is where you connect the power adaptor. Note: Please use
the power adaptor which attached for the router, for preventing from the
router damage.
3
USER MANUAL
SOLARspeed
3G Router
1.3 Features.
Conforms to the IEEE 802.11g, IEEE 802.11b, IEEE802.11n draft v2.0 standard.
Supports CSMA/CA, CSMA/CD, TCP/IP、PPPoE, DHCP、ICMP, NAT protocol.
10/100M Ethernet network (WAN) port to connect with ADSL or Ethernet. network device (for ex-
ample: Switch/Router).
Build-in SIM card slot and 3G router. ERICCSON 3G module.
LAN/WAN ports automatically detect MDI or MDIX.
Support SSID broadcast control and access control based on MAC.
Support WDS wireless network to be extended.
Built-in DHCP server.
Built-in SPI NAT firewall, support PING,Broadcast and the content of packet, MAC address, IP address,
URL and Domain name filtering.
Support static route setting.
Support VPN (PPTP/IPSec/L2TP) pass-through.
Support virtual server and DMZ.
Support UPnP, DNS PROXY.
Support built-in TD-SCDMA / WCDMA 3G wireless modem.
Supply 3G wireless network autodial, reconnection and route.
Remote WEB Management.
4
USER MANUAL
SOLARspeed
3G Router
1.4 Software Features.
1
Internet
connection, build connection with Virtual Private Network including PPTP,L2TP and so on
through WAN port.
2 Support PPPoE dialing and build link with xDSL broadband through WAN port.
3 Support static IP address setting and connect to the special net through WAN port.
4 Support DHCP Client linking.
5 Supply WAN port MAC address cloned
6 Support PPP Dialing through external 3G USB modem or built-in 3G module, and make connect to 3G
mobile network
7 Support manual or automatic option for turn on/off 3G connection,
8 Support auto-reconnect when PPP disconnection
9 Support AP client, Ethernet to WiFi converter mode so that machine can join to one
802.11b/g/n AP network.
10 Supply WEP, WPA-TKIP,WPA-AES, WPA-TKIP+AES, WPA2-TKIP,
WPA2- AES, WPA2-TKIP + AESwire-
less encryption, and support SSID broadcast control .
11 Show WAN port, LAN port, WiFi and 3G network port status.
12 Support IP address and subnet management of LAN port.
13 Support DHCP service management of LAN port.
14 Support NAT firewall setting
15 Support data packet relay and static route management
16 Support management of appending and deleting static route rule
17 Support DMZ，makethemachinecancommunicateeachotherwhether location on internet or intra-
net.
18 Support IP address ,MAC address ,port and packet filtering
19 Enable/Disable WEB long-distance management
20 Upgrading and maintaining based on WEB page
21 Set router time by hand
5
USER MANUAL
SOLARspeed
3G Router
Chapter 2.
Client Configuration.
2.1 Summary.
Before using the SOLARspeed 3G router, you need ensure that your computer Network is configured to
talk with the router.
2.2 Computer Configuration.
2.2.1 System Requiremet
When you setup the SOLARspeed 3G router, you need a computer with a network LAN port which sup-
ports TCP/IP protocol and a WEB browser e.g Microsoft Internet Explorer.
2.2.2 Network Configuration.
After connecting the SOLARspeed 3G router to your LAN, you need set your computer IP address and
other parameters to match the router.
Figure 2.3 LAN Area Connection configuration.
6
USER MANUAL
SOLARspeed
3G Router
Double click “Local Area Connection”, then popup a dialog box, select “Properties”, then select “Internet
Protocol (TCP/IP)”, click “Properties (R)”, see the following figure:
Figure 2.4 Local Area Connection properties configure
We can choose two setting-up type in the interface "Internet protocol (TCP/IP) Properties”.
Select “obtain an IP address automatically” and “obtain DNS server address automatically”, see the fol-
lowing figure:
7
USER MANUAL
SOLARspeed
3G Router
Figure 2.5 Internet Protocol (TCP/IP) properties setting
Click the “OK” button, the local computer will request assigning IP address and DNS automatically.
Note: The router default to enable DHCP server, it will assign an IP address to the computer of the local area network
automatically.
Set up fixed IP address, select “Use the following IP address” and “Use the following DNS server address”,
then fill in the following parameter.
• IP address: 192.168.0.x (x is a integer between 100-200)
• Subnet mask code :255.255.255.0
• Tacit gateway: 192.168.0.1
• DNS Server: You can fill in your local DNS server address provided by your ISP, or you can take the
router as DNS proxy server.
8
USER MANUAL
SOLARspeed
3G Router
Figure2.6 configure IP address and DNS manually.
Click the “OK” button.
The above settings is submitted, then the interface turn to “Local Area Connection Properties”, Click the
“OK” button to save the above settings.
Tip: If you are not sure of the DNS server address, we recommend you to select “Obtain an IP address automatically (O)”
and “Obtain a DNS server address automatically”.
Note：The following is the factory default setting parameter of 3G Wireless-N Router LAN port:
IP address：192.168.0.1
Subnet mask code：255.255.255.0
9
Tabla de contenidos
