Softing TH LINK PROFINET Manual de usuario

TH LINK PROFINET

Installation Manual

Version: EN-042015-1.10

The information contained in these instructions corresponds to the technical status at the time of

printing of it and is passed on with the best of our knowledge. The information in these instructions

is in no event a basis for warranty claims or contractual agreements concerning the described

products, and may especially not be deemed as warranty concerning the quality and durability

pursuant to Sec. 443 German Civil Code. We reserve the right to make any alterations or

improvements to these instructions without prior notice. The actual design of products may deviate

from the information contained in the instructions if technical alterations and product improvements

so require.

It may not, in part or in its entirety, be reproduced, copied, or transferred into electronic media.

Disclaimer of liability

Softing Industrial Automation GmbH

Richard-Reitzner-Allee 6

85540 Haar / Germany

Tel: + 49 89 4 56 56-0

Fax: + 49 89 4 56 56-488

Internet: http://industrial.softing.com

Email: info.automation@softing.com

Support: support.automation@softing.com

The latest version of this manual is available in the Softing download area at: http://industrial.softing.com.

Table of Contents

TH LINK PROFINET - Installation Manual 3

Table of Contents

Chapter 1 ..................................................................................5

Introduction

..................................................................................................... 51.1 About TH LINK

..................................................................................................... 51.2 Intended Use

..................................................................................................... 51.3 Before you connect TH LINK

..................................................................................................... 71.4 Conventions used

..................................................................................................... 81.5 Delivery scope

..................................................................................................... 81.6 Document history

..................................................................................................... 91.7 Configuration requirements

..................................................................................................... 91.8 Network presettings

Chapter 2 ..................................................................................10

TH LINK design

..................................................................................................... 102.1 Connections and display elements

..................................................................................................... 112.2 Mounting

..................................................................................................... 122.3 SD card

Chapter 3 ..................................................................................13

Start-up guideline

Chapter 4 ..................................................................................14

Mount/unmount device

..................................................................................................... 144.1 Mount device

..................................................................................................... 154.2 Unmount device

Chapter 5 ..................................................................................16

Connect to network

Chapter 6 ..................................................................................18

Connecting power supply and relay contact

Chapter 7 ..................................................................................20

Configuring the device in the network

..................................................................................................... 20

7.1 Connection in a network with DHCP server (Dynamic Host

Configuration Protocol)

..................................................................................................... 207.2 Connection in a network with manual IP address assignment

..................................................................................................... 217.3 Setting new IP and network address

..................................................................................................... 237.4 Check the connection to the device

Chapter 8 ..................................................................................24

..................................................................................................... 248.1 Login

..................................................................................................... 248.2 Logout

Chapter 9 ..................................................................................25

Settings pages

..................................................................................................... 259.1 TH LINK

................................................................................................. 26

User administration - change password9.1.1

................................................................................................. 26

TH LINK description9.1.2

TH LINK PROFINET - Installation Manual

Table of Contents

................................................................................................. 26

Network configuration9.1.3

..................................................................................................... 269.2 TH SCOPE

................................................................................................. 27

Measurement9.2.1

................................................................................................. 28

Alert9.2.2

................................................................................................. 28

Parameter distribution9.2.3

............................................................................................. 28

Set parameter provider

9.2.3.1

............................................................................................. 29

Apply parameters

9.2.3.2

............................................................................................. 30

Parameters

9.2.3.3

Chapter 10 ..................................................................................31

Firmware update

Chapter 11 ..................................................................................32

Troubleshooting

Chapter 12 ..................................................................................33

Technical Data

Chapter 1 - Introduction

TH LINK PROFINET - Installation Manual 5

1 Introduction

1.1 About TH LINK

What is TH LINK?

TH LINK TH LINK provides a secure access to the fieldbus

network and forms the basis for the Softing product TH SCOPE.

TH LINK can easily be assembled/installed and is easy to put

into operation. Integrated websites allow to configure the

product without using additional software. The delivered default

configuration allows start-up in only a few minutes. In order to

prevent network disruptions by unauthorized configuration

changes, all configuration functions are protected by user

administration.

Features

Secure access to the PROFINET network

Basis for TH SCOPE

Access protection through integrated user administration

1.2 Intended Use

The device is designed to be used as a secure access point to

PROFINET networks. Any other use is deemed non-intended use.

1.3 Before you connect TH LINK

Strictly observe the following safety instructions before connecting

the TH LINK:

Note

Small objects or liquids must not enter the case of the TH

LINK (e.g. through the ventilation slots). This may damage

the device.

Never cover the ventilation slots on the device.

Chapter 1 - Introduction

6TH LINK PROFINET - Installation Manual

Note

Never open the case of the TH LINK or carry out any

mechanical modifications on the device. This may lead to

damages on the device as well as to loss of warranty.

EMC note

The TH LINK contains electronic components sensitive to

electrostatic discharges. Damages due to electrostatic

discharge can lead to premature failure of components or

intermittent faults at a later stage. Before installing the TH

LINK, divert the electrostatic discharge away from your

body and the tools used.

Carefully plan the integration of the TH LINK into an existing

system and ensure proper function of the system after

installation.

The TH LINK may only be installed or uninstalled by qualified,

trained electrical engineering personnel. When installing the TH

LINK, observe the regulations for handling electric components

in accordance with VDE 0100. In addition, you must also

observe the valid safety and accident prevention regulations

(UVV) when operating the device within the jurisdiction of the

Federal Republic of Germany.

Always install the device on a suitable top-hat rail (mounting rail).

Cables used for the connection must not apply any mechanical

forces to the device.

High temperature differences between the storage site and

installation site can result in condensation within the case, which

may cause the TH LINK to become damaged. In case of high

temperature differences, wait at least three hours before

operating the device.

Chapter 1 - Introduction

TH LINK PROFINET - Installation Manual 7

WEEE

Electrical and electronic equipment must be disposed of

separately from normal waste at the end of its operational

lifetime.

Please dispose of this product according to the

respective national regulations or contractual

agreements. If there are any further questions

concerning the disposal of this product, please contact

Softing Industrial Automation.

1.4 Conventions used

The following conventions are used throughout Softing customer

documentation:

Keys, buttons, menu items,

commands and other elements

involving user interaction are set in

bold font and menu sequences are

separated by an arrow

Open Start Control

Panel Programs

Buttons from the user interface are

enclosed in brackets and set to bold

typeface

Press [Start] to start the

application

Coding samples, file extracts and

screen output is set in Courier font

type

MaxDlsapAddressSupp

orted=23

Filenames and directories are written

in italic

Device description files

are located in C:

\StarterKit\delivery

\software\Device

Description files

Note

This symbol is used to call attention to notable information

that should be followed during installation, use, or servicing

of this device.

Chapter 1 - Introduction

8TH LINK PROFINET - Installation Manual

Hint

This symbol is used when providing you with helpful user

hints.

1.5 Delivery scope

TH LINK PROFINET includes

TH LINK

Installation Manual

Release Note

You can find software and documentation in our download area at

http://industrial.softing.com/en/downloads.html.

1.6 Document history

Document

version

Release date

Modifications compared to

previous version

1.00

December 2014

Adaptation to new Softing

documentation structure and

layout

1.10

April 2015

New section "SD card".

Startup guideline enhanced with

SD card functionality.

New setting Data restore after

voltage recovery added to

section TH SCOPE.

Hint in section Technical data

added when using an SD card.

Chapter 1 - Introduction

TH LINK PROFINET - Installation Manual 9

1.7 Configuration requirements

(not included in the scope of delivery)

Webbrowser with Adobe Flash Player 10.0 or higher

The following ports have to be enabled in the firewall:

Protocol/purpose

Port

HTTP

80 TCP

Firmware update

1100 TCP

TH LINK communication with each

other

1123, 1124, 2364 UDP

TH LINK communication with TH

SCOPE

via Multicast

via Unicast

2364 UDP

1151, 2365, UDP

1.8 Network presettings

The device is preset to network operation with a DHCP server.

No network configuration settings are required in this operating

mode.

In case of manual allocation of IP addresses the device can be

reached via the following IP addresses (Factory setting):

For office networks:

IP Address

169.254.0.1

Subnet Mask

255.255.0.0

For automation networks:

IP Address

169.254.0.2

Subnet Mask

255.255.0.0

Chapter 2 - TH LINK design

10 TH LINK PROFINET - Installation Manual

2 TH LINK design

2.1 Connections and display elements

Figure 1: TH LINK (front and lateral view)

[1] Ethernet interface for office network

olights yellow: Ethernet data communication

olights green: physical connection available

[2] LED ETH

olights red: boot procedure

olights green: firmware update in progress

ois off: boot procedure is completed

Otros manuales para TH LINK PROFINET

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Softing

Softing

Softing CableMaster 600 Manual de usuario

Softing

Softing FiberXpert OTDR 5000 Manual de usuario

Softing

Softing CableMaster-FO Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario