Smitec FLXMOD HMI D1 Manual de usuario

HMI D1-HMI D2

Process control unit with graphical interface

Installation, use and maintenance manual

Description

Process control unit with graphical display and keypad. Main characteristics:

Equipped with 32 bit Renesas RX62 processor with 96kbytes RAM and 512kbits Flash

inside

64 kbit non-volatile RAM, 32 Mbit flash ROM and 128 Mbit SDRAM

1 USB host port (2.0)

2 FLXIO / RS 485 ports

4.3” LCD display with 24 bits color depth (16.7M colors)

13 buttons keypad with 3 LED lamps

1 Ethernet port

RTC with long life lithium coin-cell battery (CR2032)

DK400150 ver. 1.06 ─ 05/2020 1/12

bottom side connectors

4.3” display

keyboard

Ordering information

Products SMITEC part number

HMI D1 module in base version (with USB host

mode only, with two FLXIO master channels,

without Ethernet, without SD socket, without RTC,

without application software)

KZ010367

HMI D1 module in base version (with USB host

mode only, with two FLXIO master channels,

without Ethernet, without SD socket, without RTC,

with pre-loaded application software)

HMI D2 module in base version (with USB host

mode only, with two FLXIO master channels, with

Ethernet, with RTC, without SD socket, without

application software)

KZ010422

HMI D2 module in base version (with USB host

mode only, with two FLXIO master channels, with

Ethernet, with RTC, without SD socket, without

application software, with gasket on back of the

frame)

KZ010611

HMI D2 module in base version (with USB host

mode only, with two FLXIO master channels, with

Ethernet, with RTC, without SD socket, with pre-

loaded application software)

Accessories SMITEC part number

RTC CR2032 replacement battery TB010554

Adhesive gasket for back of the frame * MA804900

*: Already present in some models (see products part numbers)

Documentation SMITEC part number

User manual for HMI D1 and HMI D2 DK400150

FLXMOD system integration manual DK400076

DK400150 ver. 1.06 ─ 05/2020 2/12

Technical data

General data

Housing dimensions (width x height x depth) 210 mm x 170 mm x 37.6 mm

Weight 420 g (without connectors)

Connection method for power connector Spring cage terminals

Conductor cross-section for power connector 0.14 to 1.5 mm2 (26 ÷ 16 AWG) - 60°C

Functional earth connection By fast-on terminal on rear-panel

Mode state visual indicators Two green LED lamps for FLXIO ports status

Environment data

Permissible operating temperature +5° to +55°C

Permissible storage and transport temperature -25° to +85°C

Permissible humidity 10% to 95%, not condensing

Permissible air pressure (operation) 80 to 106 kPa (up to 2000 m above sea level)

Permissible air pressure (storage and transport) 70 to 106 kPa (up to 3000 m above sea level)

Rear degree of protection IP20 according to IEC 60529

Front degree of protection

IP65 according to IEC 60529 and UL Type 1

(guaranteed only using the adhesive gasket on back

of the frame – see accessories)

Overvoltage category II

Pollution degree 2

Means of protection (UL) Class III EC Class 2 power supply

Po er supply

Main power supply Vm

24 V DC ⎓

(-15% ÷ + 20% according to IEC 61131-2)

Maximum allowed ripple 5% of supply voltage (according to IEC 61131-2)

Current consumption from main supply 0.5 A max.

Supply overvoltage protection Bidirectional Zener clamp (Vz > 30 V)

Supply reverse polarity protection Protection diode

CPU characteristics

Microcontroller type Renesas Technology type RX62

Microcontroller architecture Harvard 32 bit

Microcontroller RAM size 96 kbytes

Microcontroller FLASH size 512 kbytes

Board external RAM 128 Mbits SDRAM

Board external non-volatile RAM 64 kbits

DK400150 ver. 1.06 ─ 05/2020 3/12

Display characteristics

Display type TFT LCD

Display size 4.3” (diagonal)

Color depth 24 bits (16.7M colors)

Communication ports

FLXIO ports 2 on RJ45 connectors, useable also as EIA RS-485

ports

FLXIO ports speed Up to 2.5 Mbps

USB 2.0 host ports 1 on standard type A female connector

Other characteristics

USB host output current 250 mA max.

Acoustic peripherals 1 buzzer

Expected battery life > 10 years

DK400150 ver. 1.06 ─ 05/2020 4/12

Mechanical dra ing

The image below depicts the mechanical dimensions of the device:

DK400150 ver. 1.06 ─ 05/2020 /12

Recommended panel cut-out

DK400150 ver. 1.06 ─ 05/2020 6/12

Mounting

The modules HMI D1/2 need to be fixed on a stable and rigid panel provided with 4xM3

metal threaded hole, min. 1.5mm deep. Use 4xM3x10mm Fe/Zn (not countersunk head type)

screws, min. class 8.8, tightened at 1 m.

IP65 protection and UL Type 1

To ensure rated protection, apply the MA804900 self adhesive gasket on back of the frame.

While applying it, stretch it slightly to match the 4 holes with the 4 holes of the frame.

See the following image.

DK400150 ver. 1.06 ─ 05/2020 7/12

Connections

The module has several connectors for power supply and peripherals (depending on version),

all located on the bottom side of the module (see illustration below).

Caution: HMI D1/2 module is an electronic high technology device with

numerous connectors; for these reasons it results an ESD sensitive device.

Observe ESD mitigation techniques or damage might occur.

Attention: Le module HMI D1/2 est un appareil électronique de haute

technologie doté de nombreux connecteurs; pour ces raisons, il en résulte un

périphérique sensible aux décharges électrostatiques. Observez les techniques de

réduction des décharges électrostatiques, sous peine de dommages.

Po er connector

The power connector is located on the bottom side

of the module; the pinout is shown in the

illustration aside.

For EMC reasons, a secure connection to earth is

always required; a suitable fast-on terminal is

provided for the purpose (labelled as FE in the

illustration).

Caution: Use a cable with cross-section suited to the current involved. A wire

smaller than necessary could cause risk of fire and unwanted voltage drops.

Caution: To ensure conformance with EMC directive 2014/30/UE, the length of

the cables must not exceed 30 m.

DK400150 ver. 1.06 ─ 05/2020 8/12

1 2

124V

2GND

Attention: Utilisez un câble de section adaptée au courant impliqué. Un fil plus

petit que nécessaire pourrait provoquer un incendie et des chutes de tension

indésirables.

Attention: pour garantir la conformité avec la directive EMC 2014/30/UE, la

longueur des câbles ne doit pas dépasser 30 m.

SD card connector

This device (depending on version), is provided with a peripheral for interfacing SD cards.

These could be used for storing large data or for updating software.

A suitable connector is provided on the bottom side of the module, able to accommodate

standard SD cards.

USB device connector

This port (depending on version), provided with a standard type mini B connector located on

the bottom side of the module, is useable as a communication port for connection with a

computer; the main purpose is data exchanging.

USB host connector

This port, provided with a standard type A connector located on the bottom side of the

module, is thought for connecting USB flash disks. Any different use should be avoided.

Note: The device HMI-D1/2 supports a large variety of USB flash disks but is

not guaranteed that all type are correctly managed; in case of troubles with one

model of USB Flash disk, try to operate with another.

Caution: ever connect a device absorbing a current beyond the rating of the

device, or internal damage might occur.

Attention: e connectez jamais un appareil absorbant un courant supérieur aux

valeurs nominales de l'appareil, cela pourrait l'endommager.

DK400150 ver. 1.06 ─ 05/2020 9/12

FLXIO / RS485 connectors

The device can act as a dual-channel FLXIO master, and two RJ45 connectors are provided

for the purpose on the bottom side of the module.

The illustration aside shows the pinout of each

connector; use standard CAT 5E Ethernet cable to wire

the buses.

Refer to the FLXMOD System Integration Manual for

bus wiring topology.

Depending on the configuration of the device, these two

ports could be used also as general purpose EIA RS485;

the maximum transmission speed is 2.5 Mbps. Even if

not mandatory, the use of shielded cable is highly

recommended, particularly when transmission speed is high.

ear each connector a green LED lamp is provided to indicate the status of the bus FLXIO;

the following table resumes all the possible states.

LED BEHAVIOUR Y TEM TATU

Blinking slowly System initialization

Searching modules on the bus

FW updating

Off (fixed) No slaves found on the bus

On (fixed) Bus operating correctly

Blinking fast Bus error

If the device is used with ports in different configuration than FLXIO, these LEDs may

assume different meanings depending on the installed firmware.

DK400150 ver. 1.06 ─ 05/2020 10/12

81DATA+

2DATA-

3GND

4NC

5NC

6NC

7NC

8NC

status LEDs

Otros manuales para FLXMOD HMI D1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Smitec

Smitec

Smitec HELCON 10 Series Guía de inicio rápido

Smitec

Smitec FLXMOD HMI D1 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario