Smeg PL7233TX Manual de usuario

INSTRUCTION MANUAL

Table of Contents

1. Description of the controls _______________________________2

2. Operating instructions__________________________________13

3. Cleaning and maintenance______________________________28

4. Troubleshooting ______________________________________32

Thank you for choosing one of our products.

You are advised to read this manual carefully; it contains all the

information you need to use your dishwasher safely, correctly and in the

most satisfactory manner.

Following the cleaning instructions provided here will keep your

dishwasher's performance at peak levels in the long term.

USER INSTRUCTIONS: these consist of recommendations for using the

appliance, a description of its controls and of the correct cleaning and

maintenance procedures.

User instructions

1. Description of the controls

1.1 Upper panel

All the dishwasher controls are grouped on the upper panel. Switching on,

programming, switching off etc. are only possible when the door is open.

1 ON/OFF BUTTON

2 OPTION BUTTONS/LIGHTS

3 SELECTED PROGRAM BUTTONS/LIGHTS

4 START/PAUSE BUTTON

5 TOP DISPLAY (3 FIGURES)

6 SALT WARNING LIGHT

7 RINSE AID WARNING LIGHT

1.2 The front panel

The front panel includes the DISPLAY which provides all information

concerning the programmed functions.

8 FRONT DISPLAY

9 DOOR HANDLE

N.B.: symbols and styling are guideline and may vary depending on

the model or version of the dishwasher purchased.

User instructions

Information shown on top display

Example of screen and information provided

01.05

Estimated wash cycle duration and time remaining

Delayed start information

E01

Error message

CHECK

h.3

Softener setting

Program cancellation

Information shown on front display

End of cycle message End

Estimated wash cycle duration and

time remaining 01: 55

Delayed start information Start in "X" hours

Error message Error 01 ……11

Softener setting h.3

Language selected IT-EN-FR……..

Program phase icons.

They indicate the program status when a

program is running

Prewash

Wash

Rinse

Drying

User instructions

LANGUAGE SELECTION

1-Switch on the dishwasher

2-Select a wash program (not Quick Time)

3-Press and hold the“half load” buttonuntil thecurrentlyselected language

appears on thefront display.

Press the button again to scroll through the available languages. When the

required language appears on the display, select it by simply waiting a few

seconds without selecting any other options (the name of the chosen

language appears on the display) or switch off the dishwasher by pressing

the on/off button.

N.B.:

- With the door open, the display switches off after about 10 seconds with

no commands.

- With the door closed, if the dishwasher is programmed but the start is not

confirmed (cycle not confirmed, program interrupted, start not confirmed…)

the name smeg appears on the display after about 10 seconds.

WASH PROGRAM SELECTION AND SWITCHING

For selection of the most suitable program for the dishes to be washed,

refer to the table below, which specifies the recommended type of wash,

also considering the type of dishes and the degree of soiling.

User instructions

PROGRAMS TABLE

PROGRAMME

NUMBER

& SYMBOL

LOAD CROCKERY AND

CUTLERY PROGRAM

PROGRESS

DURATION

CONSUMPTION

MINUTES

(1)

WATER

LITRES POWER

KWh (1)

1SOAK

Pans and dishes awaiting

completion of the load Cold prewash 15 3,5 0,02

2 GLASSES

Glass, china and mixed

dishes with light dirt.

Wash at 45°C

Cold rinse

Rinse at 70°C

Dry

9,5 1,10

3 (*)

ECONOMICAL

EN 50242

Dishes with normal dirt,

even with dried-on

residues

Wash at 45°C

Cold rinse

Rinse at 55°C

Dry

** **

4 AUTOMATIC

IEC/DIN***

Pans and dishes with

normal dirt, even with

dried-on residues.

When the "AUTO" program is selected, the dishwasher

recognises the type of dirt and automatically adjusts the

washing parameters as appropriate.

5 ULTRA

CLEAN

****

Very dirty pans and

dishes, even with dried-on

residues.

Hot prewash

Wash at 70°C

Cold rinse (2)

Rinse at 70°C

Dry

155

15,5 1,70

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

The

ULTRA CLEAN

program terminate with an extra anti-bacteria rinse that ensures

a further reduction in the bacteria level. If the temperature falls during this stage of the

program (e.g. because the door is opened or due to a power blackout), the program

lights flash to warn that the anti-bacteria effect is not guaranteed.

If the dishwasher door is open or not properly closed, the washing cycle

will not start.

User instructions

QUICK TIME PROGRAMS

(see relevant section for explanation of functioning modes)

PROGRAMME

NUMBER E

SYMBOL

LOAD CROCKERY AND

CUTLERY

PROGRAM

PROGRESS

DURATION

CONSUMPTION

MINUTI

(1)

WATER

LITRES

POWER

KWh (1)

6 RAPID 27’

Dishes with light dirt,

washed immediately after

use

Wash at 38°C

Rinse at 50°C

6,5 0,70

QUICK

DELICATE

Delicate dishes with normal

dirt.

Cold prewash

Wash at 50°C

Cold rinse

Rinse at 70°C

10,5 1,15

8 QUICK

ECO

Dishes with normal dirt,

washed immediately after

use.

Cold prewash

Wash at 60°C

Cold rinse

Rinse at 70°C

12,5 1,25

9 QUICK

NORMAL

Dishes with normal dirt,

washed immediately after

use.

Cold prewash

Wash at 70°C

Cold rinse

Rinse at 70°C

13 1,40

10 FAST

and STRONG

Mixed dishes with normal

dirt without dried-on

residues.

Wash at 65°C

Cold rinse

Rinse at 70°C

10 1,20

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

If the dishwasher door is open or not properly closed, the washing cycle

will not start.

User instructions

NOTES AND REFERENCES

Only

run the soak program with partial loads.

The options cannot be used with the soak program.

TheENERSAVE option cannot be used with soak, ultraclean, or any programs which

do not include the final drying stage.

* Standard program under

EN 50242

. If present, the

ENERSAVE

option must be

enabled.

** See information sheet provided

***

IEC/DIN

reference program. If present, the

ENERSAVE

option must

enabled.

**** Reference program for laboratories. Detergent:

20 g

in the

dispenser

10 g

the door or tablet. Configuration: see photo in "using the baskets" section.

(1) Program consumption and durationfigures havebeen measured in accordance

with the EN 50242 standard. Values may vary depending on water supply and

ambient temperatures and the type and quantity of dishes loaded.

REFERENCES for the ENERGY LABEL supplied with the dishwasher:

- Annualenergy consumptionis based on280 standard wash cycles withcold

water and consumption of low-energy operating modes. Actual consumption

depends on the way in which the appliance is used.

- Water consumption is based on 280 standard wash cycles. Actual

consumption depends on the way in which the appliance is used.

- Information refers to the EN 50242 STANDARD program (identified in the

program table), which is the most effective in terms of combined energy and

water consumption. The program is recommended for dishes with a normal

level of dirt.

- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”

(maximum efficiency).

User instructions

1.3 Wash programs

Before starting a wash program, check that:

The water supply tap is open.

The softener container contains regenerating salt.

The correct amount of detergent has been added to the

dispenser.

The baskets have been correctly loaded.

The spray arms are able to rotate freely and without

obstruction.

The dishwasher door is firmly closed.

SWITCHING ON

With the door open, press the ON/OFF button on the top panel to switch

on the dishwasher. The LED on the button and the DISPLAY light up.

PROGRAMMING

All programming operations are only possible with the door open and the

dishwasher switched on.

Select the wash program on the basis of the temperatures and type of

soiling stated in the program table.

STARTING THE PROGRAM

Select the program required (the light comes on) and any options

(after selecting the program);

Press the start button (the light comes on and the program's name

and estimated time appear on the front panel); the selected program

light flashes for a few seconds;

Close the door: the start light goes out and the program starts.

N.B.: The door must be closed within about 4 seconds; otherwise the

selected programlightstops flashing and thestart button will have to be

pressed again before the door is closed to start the program.

Tabla de contenidos

Otros manuales de Lavavajillas de Smeg

Manuales populares de Lavavajillas de otras marcas

Electrolux

Electrolux ESI5211LOX Manual de usuario

KitchenAid

KitchenAid KUDB230B Manual de usuario

Brandt

Brandt BDJ424DB Manual de usuario

Asko

Asko DSD767UXXL.AU Manual de usuario

Beko

Beko DFN26210W Manual de usuario

NEFF

NEFF S153ITX00E Hoja de especificaciones

Midea

Midea SV 4.45 wi Manual de usuario

LG LDF7932 Manual de usuario

Gorenje

Gorenje GV63214 Manual de usuario

Hotpoint

Hotpoint HDA1100ZWH Manual de servicio

Blomberg

Blomberg LDFN2240W Manual de usuario

AEG

AEG FFB83836PM Manual de usuario

Cylinda

Cylinda DM3220RFD Manual de usuario

Atag

Atag DW8214MB Manual de usuario

GE GLD8000 Series Manual de usuario

Siemens

Siemens SN23HI02KE Hoja de especificaciones

Omega

Omega ODW717X Manual de usuario

BORETTI

BORETTI BVW-683 Manual de usuario