SMC Networks 6900FSC FICHE Manual de usuario

Stackable Fast Ethernet Switch

◆ 12/24 10BASE-T/100BASE-TX ports

◆ Optional 100BASE-FX or 1000BASE-SX modules

◆ Optional stack module for linking up to four units

◆ 8.8 Gbps of aggregate switch bandwidth

◆ Support for redundant power unit

◆ Up to five port trunks per switch

◆ Port mirroring for non-intrusive analysis

◆ QoS support for two-level priority

◆ Full support for VLANs with GVRP

◆ IP Multicasting with IGMP Snooping

◆ Manageable via console, Web, SNMP/RMON

TigerSwitch 10/100

Installation Guide

SMC6912M

SMC6924M

6 Hughes

Irvine, CA 92618

Phone: (949) 707-2400

TigerSwitch 10/100

Installation Guide

From SMC’s Tiger line of feature-rich workgroup LAN solutions

February 2001

Pub. # F2.42 150070-102 R05

Information furnished by SMC Networks, Inc. (SMC) is believed to

be accurate and reliable. However, no responsibility is assumed by

SMC for its use, nor for any infringements of patents or other rights

of third parties which may result from its use. No license is granted

by implication or otherwise under any patent or patent rights of

SMC. SMC reserves the right to change specifications at any time

without notice.

SMC Networks, Inc.

6 Hughes

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of

SMC Networks, Inc. Other product and company names are trademarks or registered

trademarks of their respective holders.

IMITED

ARRANTY

Limited Warranty

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products

to be free from defects in workmanship and materials, under normal use and

service, for the applicable warranty term. All SMC products carry a standard 90-day

limited warranty from the date of purchase from SMC or its Authorized Reseller.

SMC may, at its own discretion, repair or replace any product not operating as

warranted with a similar or functionally equivalent product, during the applicable

warranty term. SMC will endeavor to repair or replace any product returned under

warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by

registering new products within 30 days of purchase from SMC or its Authorized

Reseller. Registration can be accomplished via the enclosed product registration

card or online via the SMC web site. Failure to register will not affect the standard

limited warranty. The Limited Lifetime warranty covers a product during the Life of

that Product, which is defined as the period of time during which the product is an

“Active” SMC product. A product is considered to be “Active” while it is listed on

the current SMC price list. As new technologies emerge, older technologies become

obsolete and SMC will, at its discretion, replace an older product in its product line

with one that incorporates these newer technologies. At that point, the obsolete

product is discontinued and is no longer an “Active” SMC product. A list of

discontinued products with their respective dates of discontinuance can be found at

http://www.smc.com/smc/pages_html/support.html.

All products that are replaced become the property of SMC. Replacement products

may be either new or reconditioned. Any replaced or repaired product carries

either a 30-day limited warranty or the remainder of the initial warranty, whichever

is longer. SMC is not responsible for any custom software or firmware,

configuration information, or memory data of Customer contained in, stored on, or

integrated with any products returned to SMC pursuant to any warranty. Products

returned to SMC should have any customer-installed accessory or add-on

components, such as expansion modules, removed prior to returning the product

for replacement. SMC is not responsible for these items if they are returned with the

product.

Customers must contact SMC for a Return Material Authorization number prior to

returning any product to SMC. Proof of purchase may be required. Any product

returned to SMC without a valid Return Material Authorization (RMA) number

clearly marked on the outside of the package will be returned to customers at

customer’s expense. For warranty claims within North America, please call our

toll-free customer support number at (800) 762-4968. Customers are responsible for

all shipping charges from their facility to SMC. SMC is responsible for return

shipping charges from SMC to customer.

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU

IMITED

ARRANTY

OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER

IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH

THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC

SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND

EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT

EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE,

NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS

TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED

USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR

TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,

OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR

THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY

SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the

active SMC price list. Under the limited lifetime warranty, internal and external

power supplies, fans, and cables are covered by a standard one-year warranty from

date of purchase.

SMC Networks, Inc.

6 Hughes

Irvine, CA 92618

OMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause interference to

radio communications. It has been tested and found to comply with the limits for a

Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are

designed to provide reasonable protection against such interference when operated in a

commercial environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user, at his own expense, will be required to take

whatever measures may be required to correct the interference. You are cautioned that

changes or modifications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections

—

Category 3 or

greater for 10 Mbps connections and Category 5 for 100 Mbps connections. Use 50/125

or 62.5/125 micron multimode fiber optic cable for SC or ST-type connections.

Warnings

1. Wear an anti-static wrist strap or take other suitable measures to prevent

electrostatic discharge when handling this equipment.

2. When connecting this hub to a power outlet, connect the field ground

lead on the tri-pole power plug to a valid earth ground line to prevent

electrical hazards.

EC Conformance Declaration - Class A

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí,

Barcelona, Spain.

This information technology equipment complies with the requirements of the Low

Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the CE

Mark accordingly. It conforms to the following specifications:

EMC: EN55022 (1988)/CISPR-22 (1995) Class A

IEC 1000-4-2 4 kV CD, 8 kV AD

IEC 1000-4-3 (1995) 3 V/m

IEC 1000-4-4 (1995) 1.0 kV - (power line)

0.5 kV - (signal line)

IEC 1000-4-6 (1995) 3 Vrms

OMPLIANCES

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

“Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux

appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:

“Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class A

Taiwan BSMI Class A

Australia AS/NZS 3548 (1995) - Class A

SMC contact for products in Australia is:

SMC Communications Pty. Ltd.

Suite 18, 12 Tryon Road,

Lindfield NSW2070,

Phone: 61-2-94160437

Fax: 61-2-94160474

OMPLIANCES

iii

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le

plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Underwriters Laboratories Compliance Statement

Important!

Before making connections, make sure you have the correct cord set.

Check it (read the label on the cable) against the following:

The unit automatically matches the connected input voltage. Therefore, no additional

adjustments are necessary when connecting it to any input voltage within the range

marked on the rear panel.

When using a fiber optic port, never look at the transmit laser

while it is powered on. Also, never look directly at the fiber TX

port and fiber cable ends when they are powered on.

Ne regardez jamais le laser tant qu'il est sous tension. Ne

regardez jamais directement le port TX (Transmission) à fibres

optiques et les embouts de câbles à fibres optiques tant qu'ils

sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und

auf die Faserkabelenden schauen, während diese eingeschaltet

sind.

Operating Voltage Cord Set Specifications

120 Volts UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Parallel blade, grounding type attachment plug

rated 15A, 125V

240 Volts (Europe only) Cord Set with H05VV-F cord having three

conductors with minimum diameter of 0.75 mm2

IEC-320 receptacle

Male plug rated 10A, 250V

OMPLIANCES

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine

Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur

Reinigung.

4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich

sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder

Fallen könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung

schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte

auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung

vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das

Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und

von einer qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder

Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen

Nennstrom bis 6A und einem Gerätegewicht größer 3kg ist eine Leitung nicht

leichter als H05VV-F, 3G, 0.75mm

einzusetzen.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A)

oder weniger.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de SMC Networks

SMC Networks

SMC Networks 8624T - annexe 1 Manual de programación

SMC Networks

SMC Networks TigerSwitch SMC6948L2 Manual de usuario

SMC Networks

SMC Networks EX250-SEN1 Manual de usuario

SMC Networks

SMC Networks D 7K Series Manual de usuario

SMC Networks

SMC Networks IS1000 Series Manual de usuario

SMC Networks

SMC Networks ZSE40A Manual de usuario

SMC Networks

SMC Networks 8506T Manual de usuario

SMC Networks

SMC Networks PFM7 Series Manual de usuario

SMC Networks

SMC Networks TigerAccess EE SMC7816M/VSW Manual de usuario

SMC Networks

SMC Networks SMC8612XL3 F 1.0.1.3 Manual de usuario

SMC Networks

SMC Networks PF2A7H Manual de instalación

SMC Networks

SMC Networks 6726AL2 - annexe 1 Manual de usuario

SMC Networks

SMC Networks SMC6224M Manual de usuario

SMC Networks

SMC Networks 6924MT Manual de usuario

SMC Networks

SMC Networks FS5 - annexe 1 Manual de usuario

SMC Networks

SMC Networks TigerStack II SMC8926EM Manual de usuario

SMC Networks

SMC Networks TigerSwitch SMC6724L3 Manual de usuario

SMC Networks

SMC Networks TigerSwitch SMC6709FL2 Manual de usuario

SMC Networks

SMC Networks D-M9 Series Manual de usuario

SMC Networks

SMC Networks EZ HUB 10/100 5608DS Manual de usuario

SMC Networks

SMC Networks SMCGS18P-SMART - FICHE TECHNIQUE Instrucciones de funcionamiento y seguridad

SMC Networks

SMC Networks 6824MPE INT - FICHE TECHNIQUE Manual de programación

SMC Networks

SMC Networks EZ Switch SMC-EZ1024FDT Manual de usuario

SMC Networks

SMC Networks SMC EZ Switch 10/100/1000 SMCGS8P-Smart Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario