SMC Networks EX600-WPN Manual de usuario

No.EX※※-OMV0017-B

PRODUCT NAME

I/O Configurator (NFC version)

MODEL / Series / Product Number

EX600-WEN# (Wireless master)

EX600-WPN# (Wireless master)

EX600-WSV# (Wireless slave)

-1-

No.EX※※-OMV0017-B

Contents

1. Introduction 3

1.1. Definition and terminology 5

2. Preparation before use 7

2.1. Software Installation 7

2.2. Before starting the software 8

2.3. Download the I/O Configurator (NFC version) 9

2.4. Start the I/O Configurator 10

3. Window of I/O Configurator (NFC version) 11

3.1. Basic characteristics 11

3.1.1. Login to administrator mode 13

3.2. Display for wireless master 14

3.2.1. Information tab 14

3.2.2. Input/Output monitor tab 16

3.2.3. Setting tab 20

3.3. Display for wireless slave 30

3.3.1. Information tab 30

3.3.2. Input/Output monitor tab 32

3.3.3. Setting tab 36

3.4. Detailed information of units 40

3.4.1. Information tab 40

3.4.2. Details of I/O monitor tab 49

4. Setting Function 56

4.1. Edit TAG 56

4.2. Software Control 56

4.3. Forced output 58

4.3.1. Forced output conditions 58

4.3.2. Forced output procedure 59

4.3.3. Forced output release procedure 62

4.4. Export Settings 63

4.5. Import Settings 65

4.6. Reading of the initial value 66

4.7. Initialize 67

-2-

No.EX※※-OMV0017-B

5. Pairing of wireless unit 69

5.1. Pairing procedure of wireless unit 69

5.2. Registration of dummy slave 74

6. Wireless system configuration example 75

6.1. Flow chart for using the wireless system (Refer to Step 2) 75

6.2. System Construction Example 76

6.3. Preparation 78

6.4. (1) Input and output size of the wireless slave 82

6.5. (2) Set the number of occupied I/O points for the module and

each parameter of the "wireless master" 92

6.6. (3) Set the "wireless master" system 96

6.7. (7) Ethernet setting for the wireless master 99

6.8. (4) Registration of wireless slave to the wireless master (pairing) 102

6.9. Download the configuration file 114

7. Wireless system parameter list 116

8. Error Codes 119

9. Troubleshooting 120

10. Release Notes 122

-3-

No.EX※※-OMV0017-B

1. Introduction

This operation manual describes the installation, construction of screens and operation method of the I/O

configurator for NFC. The SMC wireless system I/O Configurator for NFC can be used to check the parameter

setting of the wireless unit and the contents and status of the constructed wireless system, using an NFC

reader/writer and a PC.

There are two types of settable parameters with the I/O Configurator: the parameters which can be read or

written when no power is supplied to the product and the parameters which can be read or written only

when the power is supplied to the product.

The connection details of the I/O Configurator for NFC and the wireless unit is shown in the below figure.

※One PC will recognize one NFC reader / writer per application setting.

Do not connect multiple NFC readers / writers to a PC.

Connection details of the I/O Configurator for NFC and the wireless unit

Before the wireless system can be used, it is necessary to pair each slave with its master using the

I/O configurator for NFC.

The following sections of this document should be read before using the I/O configurator for NFC;

2. Preparation before use (page 7), which describes installation of drivers and the I/O configurator software

3.1.1. Login as administrator (page 13)

5. Pairing of wireless unit (page 69)

6. Wireless system configuration example (page 75)

NFC reader/writer

Wireless master unit

Wireless slave unit

I/O Configurator

OS (Windows)

PC/SC driver

Memory area where

power supply is

unnecessary.

Memory area where

power supply is

necessary.

Establish communication by

adjusting the position so that the

height from the center of the

NFCR/W antenna to the "O" on the

wireless unit is 1 cm or less.

※

-4-

No.EX※※-OMV0017-B

: About the communication timing

The NFC communication is not accessed all the time. Therefore, it is necessary to update the contents displayed on

the screen by clicking the "Refresh button" when reading the parameters. The parameters changed are valid after

re-supplying the power supply or by pressing the reset button in the I/O Configurator screen. As the parameter

setting requires time for settlement, do not turn off the power supply for 2 seconds.

: Establishing communication after changing units

As the settings between the wireless master unit and the wireless slave unit are different, it is necessary to update the

displayed parameter by clicking the "Refresh button" on the screen of the I/O Configurator for NFC after changing the

unit in which the parameter is set.

: Operation already checked. NFC reader/writer

SONY Corporation

RC-S380/S

Advanced Card Systems Ltd.

ACR1251U (FW212 or later), ACR1252U (FW104.6 or later)

: I/O Configurator (Web version)

This operation manual explains the outline of the setting using the I/O Configurator (NFC). I/O Configurator (Web) is

used to set the module I/O occupied points and parameters for the "wireless master" and parameters for the "I/O

devices". Refer to the operation manual for the I/O Configurator (Web version).

: The product is available in Japanese, English, and Chinese by setting the language in the Windows OS.

-5-

No.EX※※-OMV0017-B

1.1. Definition and terminology

Term

Definition

Administrator mode

Administrator mode allows the user to configure the wireless units.

Broken line detection

A broken wire to the input or output equipment has been detected by the diagnostic

function.

DHCP

A protocol that automatically allocates information, necessary to be registered to use

the network, such as an IP address, to individual devices connected to the TCP/IP

network.

Dummy slave

A Dummy slave can be used to reserve a dummy area within the I/O map.A wireless

slave can then be registered to the dummy area at a later time, without having to

change the I/O map

Export

Function to save the configured values of a wireless unit by exporting them to a PC.

Fieldbus

Network protocol to establish digital communication between an automated industrial

system such as a measurement tool or manipulation tool and a PLC.

Full duplex

Communication system that can send and receive data at the same time

bi-directionally.

Half-duplex

Communication method that can send and receive data reciprocally in bi-directional

communication.

Import

Function to reconfigure a wireless unit by importing values stored on a PC.

I/O Configurator

(NFC version)

Application used to directly set and monitor the wireless unit parameters via an NFC

reader/writer.

I/O Map

Memory area reserved for the I/O data and diagnostic information of the wireless system

IP address

A 32 bit digit sequence which is assigned to identify devices which are connected to the

network.

MAC address

A unique number inherent to all devices connected to an Ethernet network.

Manifold

Aggregate.

Module

A Module consists of a wireless master or a wireless slave combined with I/O units and

a valve manifold.

Monitor mode

Monitor mode allows the user to monitor the configuration of the wireless units but not

make setting changes.

NFC

Abbreviation of Near Field Communication. A Non-contact short distance wireless

communication used for configuration of theWireless units

Number of outputs

Number of points which can operate output equipment such as a valve, lamp or motor

starter.

-6-

No.EX※※-OMV0017-B

Term

Definition

Occupied points for

the module

input/output

Number of I/O points that can be controlled by a module.

Paring

Registration of the PID (Product ID) of the wireless slave unit to be connected to the

wireless master unit. Registration occurs at the initial setting, then wireless system will

activate.

PID

Abbreviation of Product ID. A 32 bit digit sequence which is assigned to identify the

wireless unit (master/slave unit).

PLC

Abbreviation of Programmable Logic Controller. A digital computer used for automation

of electromechanical processes.

Short circuit detection

Diagnostic function which detects generation of over current due to a short circuit

between the output and the positive power supply line or the ground line.

Short circuit

protection

Function which avoids damage to the internal circuit when over current is generated

due to short circuit between the output and the positive power supply line or the ground

line.

Refresh button

Button to display the latest configuration of the wireless units, as set by the I/O

configurator for NFC.

Reset button

Button to update the wireless units with the latest configuration set by the I/O

configurator for NFC. Note: Restarting the wireless unit will also activate the latest

configuration.

Wireless channel

Identification number of the wireless slave unit connected to the wireless master unit.

Wireless master

A unit which establishes wireless communication of input or output data to the wireless

slave. It is connected to a PLC to establish communication of input or output data.

Wireless slave

A unit which establishes wireless communication of input or output data to the wireless

master.

Wireless unit

Aunit which establishes wireless communication. This is a generic name of the wireless

master and slave units.

-7-

No.EX※※-OMV0017-B

2. Preparation before use

2.1. Software Installation

Driver: The following drivers should be installed before using this software.

When the SONY Corporation RC-S380/S NFC reader is used

(1): Microsoft. Net Framework 4.0 or higher

http://www.microsoft.com/en-US/download/details.aspx?id=17718

(2): NFC reader, writer connection driver NFC port software

(Ver 5.5.0.6 / Approx.39 MB / Apr.24.2017)

https://www.sony.net/Products/felica/business/products/RC-S380.html

When the Advanced Card Systems Ltd. ACR1251U/ACR1252U NFC reader is used.

(1): PC/SC Driver

(Ver 4.2.8.0 / 2018.3.20)

https://www.acs.com.hk/en/products/342/acr1252u-usb-nfc-reader-iii-nfc-forum-certified-reader/

When the NFC reader / writer is held over the product, an error message may appear, such as “Device driver

software was not successfully installed” or “Smart card was not identified” depending on the version of

Windows OS. The reader / writer can be continuously used.

Refer to the Microsoft website (http://support.microsoft.com/kb/976832/).

-8-

No.EX※※-OMV0017-B

2.2. Before starting the software

When the SONY Corporation RC-S380 NFC reader is used, set up the NFC port following the procedure

below. When the Advanced Card Systems Ltd. ACR1251U/ACR1252U NFC reader is used, the following

setting procedure is not necessary.

(1) The NFC setting on the control panel of your PC must be changed as follows.

Setting: Operate the NFC-B preferentially using the protocol used.

(Windows7 is used in this Operation Manual)

(2) Double-click the [NFC port/PaSoRi] icon on the control panel to display the setting window.

(Windows7 is used in this Operation Manual)

(3) When the setting window is displayed, move [NFC-F], [NFC-A] and [PicoPass] from the card information

indicated on the [Detectable cards] to the [Available cards] selection box using the "Delete" button.

Select the icon.

Select [NFC-B] only for

[Detectable cards].

-9-

No.EX※※-OMV0017-B

2.3. Download the I/O Configurator (NFC version)

(1) On the SMC website (http://www.smcworld.com), select the Documents/Download and select the

Instruction Manuals.

(2) Select the Fieldbus System Serial Transmission System.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de SMC Networks

SMC Networks

SMC Networks EX600 Series Manual de usuario

SMC Networks

SMC Networks EX600-SDN Series Manual de usuario

SMC Networks

SMC Networks EX250-SCA1A Manual de instrucciones

SMC Networks

SMC Networks EX245-SPN1 Manual de usuario

SMC Networks

SMC Networks 56-EX500-S001 Manual de instrucciones

SMC Networks

SMC Networks EX245-EA2 Series Manual de usuario

SMC Networks

SMC Networks EX250-IE1 Manual de usuario

SMC Networks

SMC Networks EX600-WEN Manual de usuario

SMC Networks

SMC Networks 56-EX500-IB1 Manual de instrucciones

SMC Networks

SMC Networks EX250-IE2 Manual de usuario

SMC Networks

SMC Networks EX600-AXA Manual de instrucciones

SMC Networks

SMC Networks EX600-SPR Series Manual de usuario

SMC Networks

SMC Networks EX245-SPN1A Manual de usuario

SMC Networks

SMC Networks EX600-WEN Manual de usuario

SMC Networks

SMC Networks EX500-IE1 Manual de instrucciones

SMC Networks

SMC Networks EX600-DYPB Manual de instrucciones

SMC Networks

SMC Networks EXW1-BMJA Series Manual de usuario

SMC Networks

SMC Networks 56-EX600-SEN7-X10 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario