SMC Networks 2208USB/ETH - annexe 1 Manual de usuario

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and

reliable. However, no responsibility is assumed by SMC for its use, nor for any

infringements of patents or other rights of third parties which may result from its use.

No license is granted by implication or otherwise under any patent or patent rights of

SMC. SMC reserves the right to change specifications at any time without notice.

The products and programs described in this User Guide are licensed products of SMC.

This User Guide contains proprietary information protected by copyright, and this User

Guide and all accompanying hardware and documentation are copyrighted.

SMC does not warrant that the hardware will work properly in all environments and

applications, and makes no warranty and representation, either implied or expressed,

with respect to the quality, performance, merchantability, or fitness for a particular

purpose.

Information in this User Guide is subject to change without notice and does not

represent a commitment on the part of SMC. SMC assumes no responsibility for any

inaccuracies that may be contained in this User Guide.

SMC makes no commitment to update or keep current the information in this User Guide,

and reserves the right to make changes to this User Guide and/or product without

notice.

No part of this manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying, recording, or information storage and

retrieval systems, for any purpose other than the purchaser's personal use, without the

express written permission of SMC.

SMC Networks, Inc.

38 Tesla

Irvine, California 92618

Trademarks

SMC® is a registered trademark; and EZ-Stream, EZ Connect, EZ Networking, Barricade,

and EZ Hub are trademarks of SMC Networks, Inc. Other product and company names

are trademarks or registered trademarks of their respective holders.

Compliances

FCC - Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with instructions, may cause harmful interference to radio

communications. However, there is no guarantee that the interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: To assure continued compliance, (for example - use only shielded

interface cables when connecting to computer or peripheral devices). Any changes or

modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

CAUTION STATEMENT:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum

distance of 5 centimeters between the radiator and your body. This transmitter must not

be co-located or operating in conjunction with any other antenna or transmitter. Note:

In order to maintain compliance with the limits of a Class B digital device, SMC requires

that you use a quality interface cable when connecting to this device. Changes or

modifications not expressly approved by SMC could void the user’s authority to operate

this equipment.

Attach unshielded twisted-pair cable (UTP) to the RJ-45 port and shielded USB cable to

the USB port.

EC Conformance Declaration - Class B

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, Planta 2,

08970 - Sant Joan Despí,

Barcelona, Spain.

This RF product complies with R&TTE Directive 99/5/EC (Annex IV) and with the

requirements of the Council Directive 89/336/EEC on the Approximation of the laws of

the Member States relating to Electromagnetic Compatibility and 73/23/EEC for

electrical equipment used within certain voltage limits and the Amendment Directive

93/68/

EEC. For the evaluation of the compliance with these Directives, the following standards

were applied:

• Electromagnetic compatibility and radio spectrum matters (ERM) EN300 328-1

(2001-12) and EN300 328-2 (2001-12)

• Electromagnetic Compatibility (EMC) Standard for radio equipment and services

EN301 489-1 and EN301 489-17

• Safety Test EN60950

• Immunity to conducted disturbances, Induced by radio-frequency fields EN

61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to EN 61000-4-8:1993 (1

A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test according to EN

61000-4-11:1994 (>95% Reduction @10ms, 30% Reduction @500 ms, >95%

Reduction @5000 ms)

• LVD: EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

• MDD: IEC 60601-1

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine

Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur

Reinigung.

4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht zugänglich

sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder

Fallen könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung

schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte

auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11.Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung

vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das

Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und

von einer qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie

mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Stellen Sie sicher, daß die Stromversorgung dieses Gerätes nach der EN60950

geprüft ist. Ausgangswerte der Stromversorgung sollten die Werte von AC 7,5-8V,

50-60Hz nicht über- oder unterschreiten sowie den minimalen

Strom von 1A nicht unterschreiten. Der arbeitsplatzbezogene Schalldruckpegel nach

DIN 45 635 Teil 1000 beträgt 70dB(A) oder weniger.

1| Package Contents

After unpacking the SMC2208USB/ETH, check the contents of the box to be sure you have received the

following components:

•1 SMC2208USB/ETH USB to 10/100Mbps Ethernet Adapter

•1 EZ Installation Wizard and Documentation CD

•1 Quick Installation Guide

Immediately inform your dealer in the event of any incorrect, missing or damaged parts. If possible, please

retain the carton and original packing materials in case there is a need to return the product.

Please register this product and upgrade the product warranty at SMC's Web site: http://www.smc.com

2| Hardware Description

SMC’s family of USB products offers a convenient and cost-effective means of bringing straightforward

peripheral connectivity to the desktop based on the Universal Serial Bus (USB). These products feature

true plug-and-play connection of PC peripherals "outside the box" and mark a significant advance in

desktop cable management. Using the EZ Networking™ USB to Ethernet Converter you can simplify PC

connections in the home, office, or on the road.

The SMC2208USB/ETH USB to 10/100 Mbps Ethernet adapter product supports Plug-and-Play and is

easy to install. The included EZ Installation Wizard makes driver/utility installation a breeze. The USB

to 10/100 Mbps Ethernet Adapter is bus-powered, hence, it draws power from the USB port of the host PC

and requires no external power supply. Simply plug in this new SMC2208USB/ETH, which uses Type A

USB port, to your Laptop/Desktop’s USB port and connect a Category 5 cable to the RJ-45 connector. You

are now ready to connect and access network resources.

Features

•USB specification 1.0, and 1.1 for standards-based compliance to ensure compatibility

•EZ Installation Wizard

•Sleek, compact, and dongleless design

•USB bus self-powered

•Supports major operating systems

Benefits

•USB 1.0 and 1.1 supports 12Mbps high data rate performance

•EZ Installation Wizard ensures easy driver/utility installation

•Compact, easy to carry form factor; solid all-in-one design with no moving parts to break

•Draws power from the USB port of the host PC and requires no external power supply

•Supports Windows 98/ME/2000/XP, Linux kernel v2.4 or later versions, Mac 9.X & 10.X.

Compatibility

•IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet

•USB v1.0 and 1.1 Specification

3| Driver Installation on Windows 98/ME/2000/XP

NOTE: Installation processes such as this may require the use of your original, licensed copy of Windows.

Please have your Windows CD available BEFORE proceeding with the installation.

Windows 98

1. Make sure your PC is powered on and that you are running the Windows 98 operating system.

2. Insert the EZ Installation Wizard and Documentation CD.

3. Click the [Install Driver] button to continue.

4. Insert the SMC2208USB/ETH (the A-type connector) into the USB port on your PC. The system will

display the "Add New Hardware Wizard" dialog box then click the "Next" button.

5. Select "Search for the Best Driver for your device (Recommended)", click the "Next" button.

6. Select "CD-ROM drive" and click the "Next" button.

7. After Windows finds the driver, click the "Next" button.

8. Windows may request you to "Insert Windows 98 CD-ROM into the driver selected, and click

OK". Follow the instruction and insert CD-ROM or disks as needed, direct Windows to the proper

location, and then click the "OK" button.

9. When Windows finishes the installation, click the "Finish" button.

10. System will ask you "Do you want to restart your computer now". Click the "Yes"button to

restart your computer.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Adaptador de SMC Networks

SMC Networks

SMC Networks 2862W-G Manual de usuario

SMC Networks

SMC Networks SMCWAPS-G Manual de usuario

SMC Networks

SMC Networks EZ Connect G SMC2835W Manual de usuario

SMC Networks

SMC Networks SMCWUSB-G Manual de usuario

SMC Networks

SMC Networks WUSBS-N2 FICHE Manual de usuario

SMC Networks

SMC Networks EZ Connect SMCWUSBS-N3 Manual de usuario

SMC Networks

SMC Networks EZ Connect N SMCWUSB-N2 Manual de usuario

SMC Networks

SMC Networks PW-DN481D Manual de usuario

SMC Networks

SMC Networks SMC2336W-AG Manual de usuario

SMC Networks

SMC Networks SMC-BT10 EZ Connect Manual de usuario

SMC Networks

SMC Networks EZ Connect g SMCWUSBT-G2 Manual de usuario

SMC Networks

SMC Networks SMCWPCI-GM Manual de usuario

SMC Networks

SMC Networks Tiger Card SMC10GPCIE-XFP Manual de usuario

SMC Networks

SMC Networks 2662W (V.4) - FICHE TECHNIQUE Manual de usuario

SMC Networks

SMC Networks WUSB-G2 FICHE Manual de usuario

SMC Networks

SMC Networks SMCWUSB-N4 Manual de usuario

SMC Networks

SMC Networks EZ Connect Powerline SMCHPAV-ETH2 Manual de usuario

SMC Networks

SMC Networks SMC EZ Connect N Draft 11n Wireless Cardbus Adapter... Manual de usuario

SMC Networks

SMC Networks 5MC2671W Manual de usuario

SMC Networks

SMC Networks WiShare SMCWTVA100 Manual de usuario

SMC Networks

SMC Networks WUSB-N2 Manual de usuario

SMC Networks

SMC Networks 2870W - annexe 1 Manual de usuario

SMC Networks

SMC Networks SMC EZ Connect g SMCWCBT-G Manual de usuario

SMC Networks

SMC Networks SMC2862W-G EZ Connect Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario