Smarter Home Platform Storage Rack 4' x 8' Manual de usuario

Platform Storage Rack

4’ x 8’

INSTALLATION MANUAL

4’ x 8’

Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MyLifter Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Platform Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1: Assemble Platform Overhead Storage Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 2: Install Smart Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 3: Install MyLifter Hoists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Step 4: Install Power Adapters and Cable Management Clips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Step 5: Attach Platform To MyLifters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table of Contents

1. This is a DO IT YOURSELF project. Read and follow the installation instructions carefully. Failure to follow instructions

could result in property damage, serious injury or death. If you have any questions or concerns about the quality of your

ceiling structure discontinue installation and consult a structural engineer.

2. Do not attempt to install any SmarterHome product or device without a basic understanding of these installation

instructions. If you are not conﬁdent locating and anchoring items to ceiling joists do not attempt this installation.

3. Do not exceed the stated weight limits noted on the platform overhead storage rack. Deﬂection of the storage rack can

happen as it reaches maximum weight load. The weight limit is based on a statically loaded storage rack that is anchored

to a wood framed garage. This system is not compatible if your house in constructed using metal studs.

4. Load the overhead storage rack evenly being sure to place heavier objects closer to the vertical uprights and the lighter

objects closer to the center.

5. Routinely inspect the storage rack to ensure rivets and wire decking are properly seated.

Safety Overview

WARNING



Lifting capacity (motorized) = 320 lbs | Weight Limit (non-motorized/static) = 600 lbs.

MyLifter Safety

When using the the MyLifter and related storage accessories:

• Do NOT use the MyLifter to lift people or animals.

• Do NOT climb or hang on the storage rack.

• Do NOT lift items while hands or other body parts are near the MyLifter device,

lifting cables, storage accessories, etc.

• Do NOT stand under the MyLifter or any items that have been lifted by the MyLifter.

• Do NOT use the MyLifter to lift or lower items over people or animals.

• Do NOT exceed the lifting capacity of the MyLifters.

• Do NOT attempt to install/secure lifters to angled ceilings or walls. MyLifter units

are designed to be secured to ﬂat ceilings only.

• Do NOT install in any manner other than as speciﬁed in instructions.

• Do NOT attempt to lift unbalanced loads. Always balance items/loads before lifting.

Inspect the MyLifter Cable(s)

• Inspect the MyLifter cable(s) often/before each use to ensure it is properly seated on the pulley wheel. If the cable is

tangled, damaged, or bent, stop using your MyLifter device immediately.

Avoid Electric Shock

• To avoid risk of electric shock and/or other potential injury DO NOT disassemble or open any SmarterHome device. All

SmarterHome products are designed for indoor use only. Failure to follow these safety instructions could result in

property damage, serious personal injury, or death.

What’s in the Box (Drawings below are not shown to scale)

Center Supports

Riveted End Rails

Ceiling bracket (non-motorized install only)

Vertical Upright (3-Hole)

Wire Decking

MyLifters Power Adapters Smart Track & Hardware

Riveted Side Rails

M6 x 15mm Bolt

M6 Flange Nut

M6 Washer

Plastic Plug

Required Tools (not included)

• Drill

• Ratchet with ½” and

10mm Socket

• Stud Finder

• Ladder

• 10mm Wrench

• Rubber Mallet

• Safety Glasses

• Pencil

• Tape Measure

• Screwdriver (ﬂat blade)

Platform Installation | Assemble Platform Overhead Storage Rack

Step 1: Assemble Platform Overhead Storage Rack

1. Align the holes on two of the riveted side rails. NOTE: All four side rails are

the same so no need to worry about using the wrong ones.

2. Using the 10mm socket and wrench plus 4 bolts, 4 washers and 4 nuts,

fasten the two riveted side rails together using the outer holes only, as shown.

Place the washer on the bolt before inserting it into the hole on the side rail.

(ﬁg 1.1). NOTE: The center holes will be used to attach the center support

later in the assembly process.

3. Repeat steps 1 and 2 for the remaining side rails. When ﬁnished with this

step, you should have two assembled side rails.

ﬁg 1.1

Do not fasten using these holes

at this stage of assembly.

Platform Installation | Assemble Platform Overhead Storage Rack

Step 1: Assemble Platform Overhead Storage Rack (cont.)

4. Join a side rail with an end rail using a vertical upright post. We suggest

using a rubber mallet and screwdriver (ﬁg 1.2) to ensure the rivets are

properly seated.

5. Once the rivets are fully seated, insert a plastic plug as shown. (ﬁg 1.3)

6. Repeat steps 4 and 5 for each of the four corners so all side and end rails are

fastened together.

NOTE

NOTE: Opposite ends of the side rails may come loose while hammering other side rails into place.

Be sure to check that all rivets are properly seated once you have attached all side and end rails.

Insert plastic plug to hold vertical

upright and rails in place.

ﬁg 1.2

ﬁg 1.3

ﬁg 1.4

Platform Installation | Assemble Platform Overhead Storage Rack

Step 1: Assemble Platform

Overhead Storage Rack (cont.)

7. Fasten the center support to the

side rails as shown using the

remaining bolts, nuts and washers.

(ﬁg 1.4)

8. Attach the remaining center

supports to the side rails by

inserting the rivets into the keyhole

openings. Make sure the rivets are

fully seated. (ﬁg 1.5)

ﬁg 1.5

Platform Installation | Assemble Platform Overhead Storage Rack

Step 1: Assemble Platform Overhead Storage Rack (cont.)

9. The frame of the platform is now fully assembled (ﬁg 1.6) and ready to add the wire decking.

10. Place the wire decking on the platform frame. The edge of each section of the wire decking (except the outer edges)

should rest on a center support. (ﬁg 1.7)

Edge of wire decking

resting on center supports.

ﬁg 1.6 ﬁg 1.7

Platform Installation | Smart Track Installation Overview

Step 2: Install Smart Track

• Lag bolts used to secure Smart Track must be centered in ceiling joists.

• If you are not conﬁdent locating and anchoring items to ceiling joists do not

attempt this installation.

• Smart Track is designed to be installed with two lag bolts. Load must only to

be applied between lag screws.

• Smart Track is designed to be secured to ﬂat garage ceilings. DO NOT mount

the Smart Track to walls or angled ceilings. Failure to follow instructions

could result in property damage, serious injury, or death.

• If you have any questions or concerns about the quality of your ceiling

structure discontinue installation and consult a structural engineer.

STOP:

Read Before

Continuing

Tabla de contenidos

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario