Smarte SLX-211 Manual de usuario
User Guide
Part No: SLX211/212UG
SmartLynx X+
Cat 5 AV Extender
Model No:
SLX-211/212
The Clearer Picture
Edition 1, July 1, 2007
Copyright 2007 Smart-e (UK) Ltd.
Notice
The information contained in this document is subject to change
without notice. Smart-e makes no warranty of any kind with regard
to this material, including but not limited to, implied warranties of
merchantability and fitness for particular purpose.
Smart-e will not be liable for errors contained herein or for inciden-
tal or consequential damages in connection with the furnishing, per-
formance or use of this material.
No part of this document may be photocopied, reproduced , or
translated into another language without prior written consent from
Smart-e (UK) Ltd.
Table of Contents
Introducing SmartLynx ................................................1
What ‘s in the box ...................................................... 1
What is SmartLynx...................................................... 2
Why is SmartLynx necessary........................................ 2
How does SmartLynx work........................................... 2
Installation and Operation ...........................................3
Transmitter ................................................................ 3
Receiver..................................................................... 6
SLX-RX212 ................................................................. 10
Appendix ......................................................................12
Specifications.............................................................. 12
Troubleshooting.......................................................... 13
Limited warranty statement ......................................... 14
Partial Product List.......................................................bp
Introducing SmartLynx Cat 5 AV Extender
What‘s in the box?
Thank you for buying the Smart-e SmartLynx Cat 5 AV Extender. Depending
on the configuration of your system various quantities of the parts below
may be included in your shipment.
If any of the accessories listed below are missing please contact the Smart-e
dealer you purchased products from or contact Smart-e customer support at:
+44 1483 283365
If you ordered a SmartLynx Set
Item Description SLX-211
Transmitter Unit
SLX-TX111 One Input and one Cat 5 Output
Transmitter unit with local output Yes
Receiver Unit
SLX-RX211 One Cat 5 Input and Multiple-option
Output Receiver unit Yes
24V Earthed PSU 24 Volt 20 Watt earthed Power Supply Yes
Mains Cable Standard PSU Mains Cable Yes
Receiver Unit
SLX-RX212 One Cat 5 Input and Dual Screen Multi-
ple-option Output Receiver unit No
SLX-212
Yes
No
Yes
Yes
Yes
Page 1 Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
What is SmartLynx?
The SmartLynx is a combination of transmitter and receiver devices
designed to transmit high resolution computer video and/or audio signal
over Cat 5 wire. AV stands for Audio Visual and includes such signal for-
mats as High-Definition and Standard Video, Broadcast Video (TV video
signal), Computer Video (VGA, SVGA, SXGA and etc. signals) and various
formats of Audio signals.
Why is SmartLynx necessary?
Sometimes AV signals need to be transmitted over distances greater than
commonly specified product limitations of 5m. In this case several choices
are available, but most are expensive and bulky, which is in some cases
simply not practical, due to space limitations in the conduits.
The SmartLynx allows the transmission of AV signals over a standard Cat 5
UTP cable over distances of up to 300m. The actual distance is a function
of the signal resolution and cable quality. The following is a rough guide
to distance and resolution:
How does SmartLynx work?
The Smart-e SmartLynx is a transmitter and receiver pair designed to extend
video, stereo audio and IR/RS232 signals over (UTP) unshielded twisted pair
category 5 (Cat 5) cabling. They are supplied with a UK power supply and
consist of: a transmitter with a video input (connectors vary by model), an
audio input and a Cat 5 output and; a receiver with a Cat 5 input and corre-
sponding outputs. Certain models are also supplied with local outputs and/or
IR or RS232 connections.
The extended signals depends on the model but supported signals are UXGA,
CVBS, YUV(YPbPr), Y/C, RGsB and RGBS analog format and Stereo Audio.
The basic concept behind this product is the ability to encode and decode
analog signal combined with precise line equalization and compensation.
Cat 5 Cable Length Maximum Recommended Resolution
Up to 300m VGA to UXGA (1600x1200)
Up to 300m SDTV
Up to 300m HDTV (720p,1080i, 1080p)
Introducing SmartLynx Cat 5 AV Extender
Page 2
Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
1. Preparing for installation
Start installation process by ensuring that all video displays and audio
devices are compatible with the computers being used. This is accom-
plished by connecting the devices directly to the computer and checking
that the devices operate as desired without the SmartLynx system.
Install CAT-5 wiring between desired locations. In order to minimize
system operation difficulties, avoid routing the system cables near fluo-
rescent lights, air conditioners, or machines that may create electrical
noise.
Installation and Operation
Page 3 Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
2. Connect Transmitter to the signal source
2.1 Connect the video output of the source device to the appropri
ate input of the transmitter using the relevant cable.
2.2 Connect the audio output of the source device to the audio
input of the transmitter using the appropriate cable.
2.3 Connect the local speakers cable to the audio loop output of the
transmitter.
2.4 If using RS232 connect control cable to the minijack input as shown
in the diagram on the previous page. Using a CAB-J19F-1M
2.5 If using Infra-Red connect the SM-LED and SM-EYE to the 3.5mm
jack points as shown in the diagram on the previous page.
3. Setting Jumpers on Transmitter to correct position
3.1 The diagram below details how to correctly set the jumpers for the
required video type.
Installation and Operation
Page 4
Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
Installation and Operation
4. System Power up
4.1 Turn the system on by plugging in the power adapter to the
SmartLynx if they are not yet connected (See diagram oppo
site).
4.2 Power up your computer.
4.3 Observe both transmitter and receiver power LED are ON,
and source device is switched on.
5. Preparing and connecting System CAT-5 cable
The SmartLynx utilizes category 5 (Cat 5), unshielded twisted pair (UTP) cable to
transport signal between transmitter and receiver.
Cat 5 cable is more desirable than coaxial cable due to its low cost and ease of
installation. This cable is used for LAN applications and is found in abundance,
already installed, in many buildings . The category 5 is a standard which estab-
lishes minimum requirements for telecommunications cabling within a commer-
cial building. The standard covers various aspects of wiring including telecom-
munications outlets.
Following is the wiring standard for terminating Cat 5 cable using RJ 45 connec-
tor:
Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8
Connectors: RJ-45
Capacitance: 14 pf/ft (46.2 pf/m)
Conductor Gauge: 24 AWG
Impedance: 100 +/- 15 ohms
4-Pair
Page 5 Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
Installation and Operation of Receiver
Page 6
1. Connecting SLX-RX211 to the display device
1.1 Making sure that the Cat 5 cable is connected to the SLX-TX111
transmitter output, connect the cable to the RJ45 socket on
the receiver unit.
1.2 If the cable connection is correct the power LED on the front of the
receiver should illuminate (power is sent up the Cat 5 cable).
1.3 Connect the display to relevant connector on the receiver
(see diagram below) using the appropriate cable
1.4 If RS232 control is required then connect to the display via the
3.5mm minijack on the receiver using a CAB-J19-1M.
Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
These would be another HD15
on the SLX-RX212
Installation and Operation of Receiver
Page 7
2. Connecting SLX-RX211 to audio and Infra-Red control
2.1 Connect the speakers or audio input on the display to the audio
output on the receiver, using a 3.5mm jack plug.
2.2 If using the receiver to transmit Infra-Red signals back down the
cable to the transmitter unit then connect an ‘eye’ to the jack
position as shown in the diagram below.
2.3 If using the receiver to transmit Infra-Red signals up to the display
from the transmitter unit then connect a ‘LED’ to the jack
position as shown in the diagram below.
Please note: connecting the IR ‘eye’ will prevent the return RS232 path from the display
Smart-e (UK) Ltd, Ranmore Manor, Ranmore Common, Dorking, Surrey, RH5 6SX
+44 (0) 1483 283365 Fax: +44 (0) 1483 281511, www.smart-e.co.uk
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Extensor de Smarte
Smarte
Smarte SmartLynx-X+ SLX-212/D Manual de usuario
Smarte
Smarte SLX-111 Manual de usuario
Smarte
Smarte SDS-901 Manual de usuario
Smarte
Smarte 4K-800 Manual de usuario
Smarte
Smarte SNX-8x8 X+ Manual de usuario
Smarte
Smarte SNX-16x16 X+ Manual de usuario
Smarte
Smarte 4K-710 Manual de usuario
Smarte
Smarte SDS-1002 Manual de usuario
Smarte
Smarte 4K-866 Manual de usuario
Smarte
Smarte SmartLynx SLX-800 Manual de usuario
