Unscrew one screw on either side of the wheelchair that holds the
seat in place.
Attach seat belt to the chair by lining up the grommet holes with
the screw holes. Re-insert screws through both the seat belt and
the chair securing the seat belt in place.
Adjust the seat belt to the desired length by
routing the strap through the buckle as shown
in Figs A-C.
Quick Start Instructions TL-2109 & TL-2109V
Need Set-up Help? (800) 650-3637
Seat Belt Installation
2
4
Mount the Fall Monitor
5Test the System
Unfasten and fasten seat belt to set o the monitor.The monitor is
now active.The monitor will sound the alert whenever the Seat
Belt is unfastened.
When the monitor is activated press the“Reset”button.This will
shut down the alerting mode.
3
Mount the monitor out of reach of the resident. Suitable
mounting location is the back of wheelchair, so that the resident
cannot tamper with monitor or reach the“Reset”button.
Connect the Seat Belt to
the Fall Monitor
A.
B.
A. Route the strap through
the buckle as shown
C. Pull the end of the
strap to tighten
B. Strap routed correctly
before tightening
Seat Belt Closed Seat Belt Opened
Bottom of
monitor
Pinch the cord together
and route it through
the strain relief recess.
Plug the cord
into the monitor.
SMART CAREGIVER CORPORATION
Tel: 800-650-3637 | www.smartcaregiver.com
For more information about the
Caregiver Key™, and how it can be used
in your facility’s Fall Assessment Program
call 800-650-3637
* Tamper Proof mode not available on TL-2100E
Resetting the Monitor/ Tamper Proof ™Mode with Caregiver Key™(Optional)
Caregivers can choose to reset the
TL-2100S in either of two ways:
Select either “Reset Button ON”or
“Reset Button OFF, Use Caregiver
Key™ To Turn OFF”with the switch on
the side of the TL-2100S Fall Monitor.
1. Press the Reset button on the front
of the monitor (“Reset Button ON”
mode).
2. Place the optional Caregiver Key™ over
the red dot on the front of the monitor.
(“Reset Button OFF, Use Caregiver
Key™ To Turn OFF” mode).
This mode allows only the caregiver
to reset the monitor.
“Reset Button ON”Mode
Press the Reset button to reset the
monitor.
“Reset Button OFF, Use Caregiver Key™ To Turn OFF” Mode.
Place the Caregiver Key™ over the red dot to reset the monitor.
For more information about the
Caregiver Key™and how it can be
used in your facility’s Fall Assessment
Program call 800-650-3637
Safety Auto Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
Safety Auto Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
Refer to User Instructions
before changing this setting.
Reset Button-
ON
Reset Button OFF
Use Caregiver Key
To Turn OFF
6V DC
300mA MAX
-
Install
Batteries
1
The battery compartment
door is secured with the
included Phillips-head screw
Alert Volume
Adjustment
Tone
Adjustment
Alert Delay
Adjustment
Warning: Failureto comply with warning may result in injury
or death. Thisdevice is not suitable for all individuals. Other
devices may be required.This device is not a substitute for
visual monitoring by caregiver.Sensor pad fall monitors are
prone to diculties. Be sure cordc annot entangleor choke the
user.The manufacturer does not claim that this device will
stop elopement and/or stop falls.This device is designed to
agument caregivers comprehensiveresident mobility
management program.Test this device before each use.
Read the instructions and legal disclaimer.
Read Instructions Before Use:
Battery not included. Use 3 x AA alkaline Batteries.
Set Up: Plug sensor pad into the fall monitor.Apply pressure to
the sensor pad to test the system.The monitor will emit two
beeps, indicating that the system is working.The Monitor
Status LED will blink every 3 seconds when the system is
activated and operating properly.
Delay
2sec 1sec 0sec3 2 1 Dcrease/Increase
Volume
Tone
Close battery door and secure
it with small Philips-head
screw.
Place monitor back into its
plastic protective boot.
