SMART SBID 8084i-G4 Manual de usuario

Tabla de contenidos

Otros manuales de Pizarra interactiva de SMART

SMART

SMART KAPP42 Manual de usuario

SMART

SMART kapp 84 Manual de usuario

SMART

SMART Room System Manual de funcionamiento

SMART

SMART Board MX Manual de usuario

SMART

SMART KAPP iQ PRO 65 Manual de usuario

SMART

SMART KAPP42 Manual de usuario

SMART

SMART SC12A Guía del usuario

SMART

SMART 685ix2 Manual de usuario

SMART

SMART Room System SRS-LYNC-XS Manual de servicio

SMART

SMART 8070i-G4-SMP Manual de funcionamiento

SMART

SMART board 8000i-G4 series Manual de funcionamiento

SMART

SMART SMART Board 885-SMP Manual de usuario

SMART

SMART KAPP IQ Guía de instalación

SMART

SMART Table 230i Manual de instalación

SMART

SMART SBID-7286 Manual de usuario

SMART

SMART kapp iQ 55 Manual de usuario

SMART

SMART KAPP iQ PRO 55 Manual de servicio

SMART

SMART Board 800 Series Manual de usuario

SMART

SMART Board 7000 Manual de usuario

SMART

SMART Inforce 67X1 Manual de usuario

SMART

SMART SB880i5-MP Manual de usuario

SMART

SMART Board 885ix2-NCP Manual de usuario

SMART

SMART Board 6000 Series Manual de usuario

SMART

SMART Board 600i3 Manual de usuario

Manuales populares de Pizarra interactiva de otras marcas

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Manual de usuario

Buhl

Buhl LyteBoard Manual de usuario

SMART Board

SMART Board 680 Manual de usuario

Legamaster

Legamaster e-SCREEN ETX Manual de usuario

SMART Board

SMART Board SBM685ix2 Manual de usuario

Seneca

Seneca eno Manual de usuario

BenQ

BenQ RP840G Manual de usuario

Olivetti

Olivetti OLIBOARD Manual de usuario

Turning Technologies

Turning Technologies MOBIVIEW Manual de usuario

Panasonic

Panasonic UB-5335 Manual de usuario

Dukane

Dukane ITP84 Manual de usuario

Bretford

Bretford EDUIMS Guía de configuración

Panasonic

Panasonic Panaboard UB-5315 Manual de usuario

Plus

Plus M-11S Manual de usuario

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Manual de usuario

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Manual de usuario

AVer

AVer CP series Manual de usuario

Genee

Genee 56" Manual de usuario

1 smarttech.com/kb/170597 1022737 Rev 01

Important

Before you configure your

SMARTBoard® 8084i-G4

interactive flat panel

You need to set the computer (or Microsoft®Lync® appliance) input’s operating mode to “PC” after

you turn on your SMARTBoard® 8084i-G4 interactive flat panel for the first time but before you

configure and use the interactive flat panel.

I M P O R T A N T

If you do not complete this procedure, the following could occur:

lThe interactive flat panel might not display the outer edges of the computer’s display.

lUsers might notice higher than normal video display latency.

To set the computer input’s operating mode to “PC”

1. Turn on the interactive flat panel.

2. If you’re installing the interactive flat panel as part of a SMARTRoomSystem™ for

MicrosoftLync, set the Lync Room Reset option as described in chapter 3 of the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

3. On the remote control, press INPUT (a), and then press the red button (b),

which is below the BACK button.

The Input Label menu appears.

I M P O R T A N T

Before you configure your SMARTBoard 8084i-G4 interactive flat panel

2 smarttech.com/kb/170597 1022737 Rev 01

4. Using the left and right arrow buttons on the remote control, select the input that the computer is

connected to, and then press OK.

N O T E

If you’re installing the interactive flat panel as part of a SMARTRoomSystem, select

HDMI3/PC.

5. Using the left, right, up and down arrow buttons on the remote control, select PC, and then

pressOK.

6. Press the down arrow on the remote control to select Close, and then press OK.

In the Input List menu, the computer input’s icon indicates that its operating mode is “PC.”

7. Calibrate and orient the interactive flat panel as documented in the SMARTBoard 8000i-G4

interactive flat panel setup and maintenance guide (smarttech.com/kb/170446) or the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

N O T E

In most situations, the only time you need to make this change is during the initial

configuration of the interactive flat panel. However, if you subsequently complete a

FactoryReset or LyncRoomReset, you need to complete this procedure afterward.

smarttech.com/support

smarttech.com/contactsupport

© 2013SMARTTechnologiesULC. All rights reserved. SMARTBoard, SMARTRoomSystem, smarttech, the SMART logo and all SMART taglines are trademarks or

registered trademarks of SMARTTechnologiesULC in the U.S. and/or other countries. Microsoft and Lync are either registered trademarks or trademarks of Microsoft

Corporation in the U.S. and/or other countries. All other third-party product and company names may be trademarks of their respective owners. Contents are subject to

change without notice. 10/2013.