Smart view 184A Manual de usuario
Smartview
Door Camcorder with Color Monitor and
Motion Sensor
Model No. 184A
Product by: J Domótica – TEC IT, Tecnologia
Inteligência e Domótica, S.A.
Travessa Cabo do Mundo, 681 | 4455-427 Perafita Matosinhos
PORTU AL
Phone. +351 229 999 230 | Fax. +351 229 999 249
email: domoti[email protected] | www.jgdomotica.com
USER’S GUIDE
Caution
Do not rotate the camera or recorder without disconnecting the connecting
cable first. Damage to the connecting cable will occur!
Before attempting to connect or operate this product, please read
these instructions carefully and save this manual for future
reference
CONGRATULATIONS
With this Door Camcorder with Motion Sensor, you can capture the
video/audio of any visitors even when you are not home. It also allows you to
answer your door safely at home before opening. It is a high-quality, battery-
operated security device that uses a passive infrared (PIR) motion sensor to
detect guests/intruders at your front or back door, and to activate a video
recording and an on-screen image at your home’s side.
This instruction manual explains in simple steps how to install, use and care
for your new Door Camcorder in homes, offices or businesses.
PARTS CHECKLIST
Identify all parts before proceeding with installation
1pc. Charger
1pc. Rechargeable Battery
1pc. Clock Battery
(installed in Camcorder)
1pc. Color Monitor
1pc. Front Sensor with double-
side tape 1pc. Mounting Bracket
2 pcs Supporter
1pc. Screw for Bracket
1pc. Tool
Optional SD/MMC card
(if supplied)
FCC Warning
Any unauthorized changes or modifications to this equipment would void the
users authority to operate
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Important Safeguards
1. Cleaning – Turn off this video unit before cleaning. Do not use strong
or abrasive detergents. Use a dry cloth to clean the camera body when
dirty. In case the dirt is hard to remove, use a damp (not wet) cloth for
cleaning.
2. Water and Moisture – Do not use any component of this system in
an exposed outdoor area except the outer part of front sensor, unless the
instructions clearly state that it is safe to. Do not operate this system in
the presence of explosive or flammable fumes.
Precautions
1. Do not attempt to disassemble the camera. There are no user-serviceable
parts inside.
2. Handle the Smartview with care.
Do not abuse the camcorder. Avoid striking, shaking, etc. Improper
handing or storage could damage the device. Modifying or tampering
with the device or its internal components can cause a malfunction and
THINGS YOU SHOULD KNOW
invalidate the device’s warranty. If your device is not performing as it
should, take it to your local dealer for assistance.
3. Clean the lens faceplate with care. Do not clean the lens with
strong or abrasive detergents. Use lens tissue or a cotton tipped applicator
and ethanol.
4. Door Mounting – The product should be mounted to a door, only as
recommended by the manufacturer
5. Set MODE to PLAY when you are not using your camcorder. It will set
the motion detector off and the device to enter the Stand-by status until
pressing POWER.
6. Do not touch the LCD screen with a sharp-pointed object.
7. If your Smartview is used in a cold place, a residual image may appear
on the LCD screen. This is not a malfunction
Privacy Perception
Always use discretion when installing video and audio surveillance equipment
especially when there is perceived privacy, or an expectation of privacy.
Inquire regarding federal, state and/or local regulations applicable to the
lawful installation of video and/or audio recording or surveillance equipment.
Party consent may be required.
FEATURES
Monitor and Sensor Front
1. LCD Screen - 1.5” LTPS LCD
2. Speaker - play back the audio sound of recorded file at PLAY mode
3. SD/MMC Card Insert Slot
4. Battery Cover
5. Microphone
6. Motion-activated Sensor – detects motion up to 2 meters (6.5 feet) away
and from a horizontal angle of up to 125 degrees
7. Lens
Monitor and Sensor Monitor Back
1. Terminal
2. Clock Battery Cover
Control Panel
1. OK – confirm setting
2. CURSOR –◀▶
3. MENU – enter Menu screen
4. DISPLAY – press this button to toggle among Full Display On, Texts
Off and Display Off
5. MODE switch – go to RECORD, LIVE, or PLAY
6. POWER – activates and deactivates the device at selected mode
7. RESET – use a pointer or alike to press this button to reset the unit
Operation Indicators
1. New Message Light Indicator ( reen)
2. Full Memory Light Indicator (Red)
3. Key Light uide (Blue) – illuminates when user presses any button
4. Low Battery Light Indicator (Red)
PREPARATION
Charging CAMERA Battery
Charge Battery fully before use
1. Plug in Charger. Red light is on.
2. Insert Battery onto the Charger, observing proper +/- polarities as
indicated. Red light flashes.
3. When charging is complete, the light changes to reen color.
4. Remove Battery.
Notes:
* Charging takes about 2 hours.
* Amber light will be on in case of abnormal use or bad battery.
* Prevent metallic objects from coming into contact with the metal parts of
the terminal of Charger. This may cause a short circuit, damaging the
Charger.
* Keep the battery dry.
* Battery life gradually decreases after repeated use and recharging. If
operation time becomes very short even after a sufficient charge, discard
Battery properly.
* When the battery is not to be used for a long time, charge the battery
once fully, and then use it until it fully discharges again. Keep it in a
good condition.
Install Battery
1. Press and slide down the battery cover. It will be opened up horizontally.
2. Install a fully charged Battery into the battery compartment, observing
proper +/- polarities direction as indicated.
3. Press down and slide up to lock the battery cover.
To remove Battery
1. Press and slide down the battery cover. It will be opened up horizontally.
2. Press Orange BATT RELEASE down to slide the Battery out.
3. Press down and slide up to lock the battery cover.
Battery Care
Caution:
- Charge only with specified charger
- Battery can be charged within a temperature range of 10C (50F) and 35C
(95F)
- Battery is normally warm after charging or just after use.
- Do not use an insufficiently charged or worn-out Battery
Safety precautions:
- Do not get Battery near, or dispose of, in fire
- Do not directly connect (short circuit) the positive (+) and negative (-)
terminals
- Never attempt to disassemble or reassemble Battery
To avoid Battery damage:
- Do not drop or jar Battery
- Use Battery with specified units only
- If Battery is used in extremely high temperatures, a safety device will
automatically prevent operation
To prolong Battery life:
- While not in use, remove Battery from the Smartview and Charger, and
store in a cool, dark, dry place.
- Keep Battery terminal clean
Charger Caution:
- This unit will operate on AC 100-240 V 50/60Hz.
- Grounding or Polarization – This video unit may be equipped with either a
polarized 2-wire AC (Alternating Current) line plug (a plug having a blade
wider than the other) or 3-wire grounding type plug, a plug having a third
(grounding) pin.
If the 2-wire polarized plug fails to fit into the power outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
The 3-wire grounding type plug will fit into the grounding type power
outlet. This is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the grounding type plug.
- Power-Cord Protection – Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them. Paying particular attention to cords of plugs, convenience receptacles,
and the point where they exit from the unit.
- Overloading – Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
- During charging operation, the battery should be kept away from high
temperature, high pressure and heat sources. Also it should be kept away
from children. Do not charge the battery for over 24 hours.
CLOCK Battery Installation
Tabla de contenidos
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario