Guest laptop (USB 2)
< 52' (16 m)
f
h
VGA
kg
f
Remotely managing your
SMART Board™ 8070i
interactive display
Connectingyourinteractive display to anRS-232system 2
Connectiondiagram 2
Serialinterfacesettings3
Powermodes4
RS-232programmingcommandsandresponses 4
Interpretingthe“invalidcmd” response 5
Commandinventory 5
Designatingvideoinput s ourcecommands f ora s pecific video input6
Designatingatarget interactive display 7
Commandsandcontrols 8
Powerstatecommands8
Videoinputs ource 9
Videosourcecommands10
Audiooutputc ommands13
Systeminformationcommands14
Serviceinformation 18
Thisdocumentincludesdet ailedinstructions onhowto s et up your computer orroom control system
toremotelymanage your SMART Board™8070iinteractive display using an RS-232 serial interface.
1
USB 2 HDMI/DVI
CopyrightSMART Technologies. All Rights Reserved.Header
Configuringthe video and touch inp utfor your SMA RTBo ard 8070i interactive display
Overview
Youcan connect your SMART Board 8070i interactive di splay to up to three computers at once. Each computer must be conne cted to the interactive
displaywith a USB cable for touc h input and a video cable for video input.
Thefollowing table shows the default touch input and vi deo input pairings.
Ifyou want to use a video and touch input pairing other than the default, y ou can change the video input settings in the Video and Touch Input Settings
windowof the SMART control panel.
NO T E
Ifmultiple interactive displays are connectedto your room computer, disconnect all but one of the interactive displays,and then con figure the interactive
displaysone at a time.
Details
SMARThardware SMARTBoard 8070i interac tive displays
SMARTsoftware SMART Notebook 10.8 SP1 collaborative learning software,SMART Meeting Pro 2.3 so ftware andS MART
ProductDrivers 10.8
Operatingsystems Windowsoperating systems and Mac OS operating system software
Computer Touchinput connection Defaultvideo input connecti on
Roomcomputer USB 1 VGA
Guestlaptop USB2 RGB/HV
Sidelaptop USB3 HDMI2
Usingthe computer that’s connecte d to the USB 1 connection, configure the video input for each touc h input connection using the Video and Touch Input
Settingswindow.
IM P O R T ANT
Youmust have the latest version of SMART N otebook software or SMART Meeting Prosoftwa re installedon the computer connec ted to USB 1.
Theinteractive display status lightmust begreen orflashing green.
Theinteractive display cannot be in Eco -Standby mode.
Page1 of 3Configuring the video and touch input for your SMART Board 8070i interactive display (...
2/5/2012http://www.smarttech.com/us/Support/Browse+Support/Support+Documents/KB4/170065.a...
DVI
HDMI
DVI HDMI
j
m
OR OR
1
Extending
USBConnections
SMARTBoard®800 seriesinteractive
whiteboardsand systems
Room
control
n
Bottom connection panel
Speakers
1
2
Inside
connection
panel
c
e
Guest laptop (USB 3)
The USB drive connects
to the appliance.
Side laptop
connection panel
< 52' (16 m)
h
HDMI
j
p
q
p
a
Audio
connection
panel
Appliance
SBID 8070ie-MP appliance
Forcautions, warnings and other important product information see Important information for your
SMARTBoard™ interactive display ( ).
1
2
b
a
smarttech.com/kb/160469
smarttech.com/kb/170166
smarttech.com/kb/170132
smarttech.com/kb/170157
smarttech.com/kb/170065
smarttech.com/kb/170166
Alternative cable connections
