SMART-AVI SM-DVN Series Manual de usuario

Advanced 4/8 DVI-I Matrix KVM 1

1-800-284-2131

www.smartavi.com

USER MANUAL

Advanced 4/8-Port DVI-D matrix KVM

SM-DVN-44X 4-Port DVI-D KVM Matrix, 4 Users

SM-DVN-82X 8-Port DVI-D KVM Matrix, 2 Users

SM-DVN-84X 8-Port DVI-D KVM Matrix, 4 Users

SM-DVN matrix series

Advanced 4/8 DVI-I Matrix KVM 2

TECHNICAL SPECIFICATIONS_____________________________________________________________ 3

WHAT’S IN THE BOX?_____________________________________________________________________ 4

SM-DVN FRONT AND REAR_______________________________________________________________ 4

INSTALLATION____________________________________________________________________________ 5-8

LED’s BEHAVIOR__________________________________________________________________________ 11

SYSTEM OPERATION______________________________________________________________________12

TROUBLESHOOTING______________________________________________________________________ 12

TECHNICAL SUPPORT_____________________________________________________________________12

LIMITED WARRANTY STATEMENT________________________________________________________ 13

Table of contents

Advanced 4/8 DVI-I Matrix KVM 3

VIDEO

Format DVI-I Dual Link

Host Interface SM-DVN-44X (4) DVI-I 29-pin (female) / DVI-D

SM-DVN-82X / SM-DVN-84X (8) DVI-I 29-pin (female) / DVI-D

User Console

Interface

SM-DVN-82X (2) DVI-I 29-pin (female) / DVI-D

SM-DVN-44X / SM-DVN-84X (4) DVI-I 29-pin (female) / DVI-D

Max Resoluon 2560 x 1600 @ 60Hz; 3840x2160 @ 30Hz (w/HDMI-to-DVI adapter)

DDC 5 volts p-p (TTL)

Input Equalizaon Automac

Input Cable Length Up to 20 .

Output Cable Length Up to 20 .

AUDIO

Input (4) / (8) Connector Stereo 3.5mm Female

Output (2) / (4) Connector Stereo 3.5mm Female

CONTROL

Front Panel Push Buons with LED indicators

RS232 Via Serial @ 115200 bps

Hot Keys Via Keyboard

POWER

Power Requirements

SM-DVN-44X 12V DC, 2A (minimum) power adapter with center-pin posive polarity.

SM-DVN-82X /

SM-DVN-84X 12V DC, 3A (minimum) power adapter with center-pin posive polarity.

ENVIRONMENT

Operang Temp 32° to 104° F (0° to 40° C)

Storage Temp -4° to 140° F (-20° to 60° C)

Humidity 0-80% RH, non-condensing

OTHER

Emulaon Keyboard, Mouse and Video

Control Front Panel Buons

Technical Specifications

USB

Signal Type USB 2.0, 1.1, and 1.0 w/ internal hub

Type A to B SM-DVN-44X (4)

SM-DVN-82X / SM-DVN-84X (8)

User Console Interface (2) USB Type-A for keyboard and mouse connecon only

Advanced 4/8 DVI-I Matrix KVM 4

SM-DVN Unit 4/8-port DVI-D Matrix KVM

PS12VDC2A or

PS12VDC3A

12V DC, 2A (minimum) power adapter with center-pin posive polarity or

12V DC, 3A (minimum) power adapter with center-pin posive polarity.

User Manual

What’s in the box?

SM-DVN-84X rear

SM-DVN-84X front

SM-DVN-44X rear

SM-DVN-44X front

Advanced 4/8 DVI-I Matrix KVM 5

1. Ensure that power is turned o or disconnected from the unit and the computers.

2. Use a DVI cable to connect the DVI output port from each computer to the

corresponding DVI-D IN ports of the unit.

3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the

respecve USB ports of the unit.

4. Oponally, connect a stereo audio cable (3.5mm to 3.5mm) to the audio output of each

computer to the AUDIO IN ports of the unit.

5. For each user, connect a monitor to each DVI-D OUT console port of the unit using

DVI cables.

6. For each user, connect a USB keyboard and mouse to the two USB console ports.

7. Oponally, for each user, connect stereo speakers to the AUDIO OUT ports of the unit.

8. Finally, power on the KVM by connecng a 12VDC power supply to the power

connector, and then turn on all the computers.

Note: You can connect up to 8 computers to the 8 port KVM and up to 4 computers to the 4 port

KVM.

installation

SM-DVN-44X Shown

Advanced 4/8 DVI-I Matrix KVM 6

Installation (continued)

SM-DVN-84X Shown

Advanced 4/8 DVI-I Matrix KVM 7

Installation (continued)

EDID Learn:

The KVM is designed to learn the connected monitor’s EDID upon power up. In the event of

connecng a new monitor to the KVM, a power recycle is required.

The KVM will indicate to the user that the EDID learn process is ongoing by ashing the LED next to

DVI OUT port 1. When the LEDs stop ashing, the EDID learn process is done.

The monitor must be connected to the video output connector located in the console space at the

back of the KVM during the EDID learn process.

If the read EDID from the connected monitor is idencal to the current stored EDID in the KVM then

the EDID learn funcon will be skipped unless the force learn EDID process is used. To force learn

the EDID, hold down the First and Last CAC buons of Front Panel for 3 seconds to force Learn

Advanced 4/8 DVI-I Matrix KVM 8

System operation

There are three ways to control the SM-DVN: Keyboard Hotkeys, RS-232 Serial Commands, and

Front Panel Buons. All modes of control will allow the user the set their desired conguraons.

front panel control

To switch to an input port for a given console, push the UP or DOWN buons as many mes as

needed to navigate to the desired channel. The channel number indicator will display to selected

channel for each console.

By default, the unit will start in View Mode, indicated by a red LED above the CAC buon on the

front panel. In View Mode, keyboard and mouse funconality are disabled. Control Mode enables full

keyboard and mouse funconality.

hotkey and rs232 serial control

The SM-DVN may also be controlled via RS-232 commands. To use these commands, you must use

HyperTerminal or an alternave terminal applicaon. The sengs for the connecon are as follows:

Baudrate 115200; Data Bits 8; Parity None; Stop Bits 1; Flow Control None.

Once you have connected to the SM-DVN via Serial, you will see the SM-DVN informaon when the

device starts up.

The following commands can be used for RS-232 with available keyboard hotkeys:

Command Descripon HotKey RS-232 Command

Switch all USB devices and

Main video

[CTRL][CTRL] c [port #]

[ENTER]

//c[user #] [port #]

[ENTER]

Switch Channel View Only [CTRL][CTRL] v [port #]

[ENTER]

//v[user #] [port #]

[ENTER]

Learn EDID [CTRL][CTRL] e [ENTER] //e[ENTER]

Trigger Hotplug [CTRL][CTRL] h [ENTER] //h[ENTER]

Reset Soware [CTRL][CTRL] r [ENTER] //r[ENTER]

View Current Hotkey N/A //hk [ENTER]

Advanced 4/8 DVI-I Matrix KVM 9

Custom hotkey triggers

Users are able to customize the keys that trigger Hotkeys. The default trigger for hot key funcon on

the Keyboard is Ctrl +Ctrl. The trigger funcon can be used to change to double Ctrl, Shi, or Scroll

Lock.

To view hotkey trigger seng:

Type on Keyboard: Alt + Alt + Alt + k + 0 + [Enter]

The LED Light on the user’s keyboard will Flash indicang which trigger is currently acve

Num Lock LED ash indicates CTRL

Caps Lock LED ash indicates Shi

Scroll Lock LED ash indicates Scroll Lock

To change the hotkey trigger seng:

Hotkey trigger twice + k + [1 | 2 | 3]

1 - Ctrl

2 - Shi

3 - Scroll Lock

Example: If the hotkey trigger is Shi and would like to change to Scroll Lock,

Type: Shi + Shi + k + 3

Advanced 4/8 DVI-I Matrix KVM 10

User Console Interface – Display LED:

Front Panel – Port Selecon LED’s:

EDID Learn - Front Panel LED’s:

All LED’s are turned on for 1 second. Then:

 Port 1 LED’s will ash unl the end of the process.

#Status Descripon

1O Monitor is not connected

2On Monitor is connected

3Flashing (back panel) EDID problem – Learn EDID to x the problem

#Status Descripon

1Red View Mode

2Green Control Mode

Led’s behavior

Otros manuales para SM-DVN Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de SMART-AVI

SMART-AVI

SMART-AVI SM-UHO Series Manual de usuario

SMART-AVI

SMART-AVI UHDN-4P-DUO Manual de usuario

SMART-AVI

SMART-AVI SM-DPN Series Manual de usuario

SMART-AVI

SMART-AVI DV-SW4 Manual de usuario

SMART-AVI

SMART-AVI DVN-4DUO-DL Manual de usuario

SMART-AVI

SMART-AVI DPN-4DUO Manual de usuario

SMART-AVI

SMART-AVI DVN-4QUAD Manual de usuario

SMART-AVI

SMART-AVI HDR-4X4-PLUS-V2 Manual de usuario

SMART-AVI

SMART-AVI CATSWITCH Manual de usuario

SMART-AVI

SMART-AVI DPN-4P Manual de usuario

SMART-AVI

SMART-AVI HDR32X32 Plus Manual de usuario

SMART-AVI

SMART-AVI SM-DVN-4Q Manual de usuario

SMART-AVI

SMART-AVI HDN-4QUAD Manual de usuario

SMART-AVI

SMART-AVI SM3-UHX-2D Manual de usuario

SMART-AVI

SMART-AVI QuadKVM Manual de usuario

SMART-AVI

SMART-AVI SM-HDN-4S-S Manual de usuario

SMART-AVI

SMART-AVI DVN-8P Manual de usuario

SMART-AVI

SMART-AVI DPN-4 Quad Manual de usuario

SMART-AVI

SMART-AVI DV-SW2S Manual de usuario

SMART-AVI

SMART-AVI SKM-04-PRO Manual de usuario

SMART-AVI

SMART-AVI DPN-4QUAD Manual de usuario

SMART-AVI

SMART-AVI DVN-16Pro Manual de usuario

SMART-AVI

SMART-AVI QKVMPro Manual de usuario

SMART-AVI

SMART-AVI DVN-16Pro Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario