Smappee Infinity Manual de usuario

English –Version 1.2 –January 2021

Smappee Infinity

and EVBox

Install guide

English –Version 1.2 –January 2021

Table of contents

1. Compatibility............................................................................................ 3

2. Smappee Smart EV charging.................................................................... 5

3. Installation Procedure ............................................................................. 6

4. Physical installation ................................................................................... 7

5. Configuration .......................................................................................... 12

6. Validation of the installation.................................................................... 18

7. Set up smart EV charging......................................................................... 19

English –Version 1.2 –January 2021

1. Compatibility

Smappee hardware

EVBox car charging stations are only compatible with Smappee Smart EV charging if one of the

available preconfigured Smart Charging kits is used or when a Smappee Infinity setup with Genius as

gateway is used. In the latter case, Smart Charging Connectors must be purchased separately.

Compatible Smart Charging kits:

Article number

Commercial name

SMARTC-1P50A-2

Smart Charging 1-Phase (50A)

SMARTCPLUS-1P50A-2

Smart Charging Plus 1-Phase (50A)

SMARTC-1P100A-2

Smart Charging 1-Phase (100A)

SMARTCPLUS-1P100A-2

Smart Charging Plus 1-Phase (100A)

SMARTC-3P50A-2

Smart Charging 3-Phase (50A)

SMARTCPLUS-3P50A-2

Smart Charging Plus 3-Phase (50A)

SMARTC-3P100A-2

Smart Charging 3-Phase (100A)

SMARTCPLUS-3P100A-2

Smart Charging Plus 3-Phase (100A)

Smappee Smart Charging kits use a Smappee Connect as gateway, whereas Smappee Smart Charging

Plus kits use a Smappee Genius. All kits are available in a 50A version and a 100A version for the UK

market.

If the Smappee Genius gateway is purchased separately and not as part of a Smart Charging (Plus) kit,

a set of Smart Charging Connectors is required:

IMPORTANT: Smappee Smart EV charging won’t work with a Smappee Connect

unless this gateway is part of a Smart Charging kit.

IMPORTANT: The components in the kit (Power Box, CT hub(s) and Connect or

Genius unit) are pre-configured and are specific to one kit. These components

cannot be used with a different kit.

English –Version 1.2 –January 2021

Article number

Commercial name

SMARTC-CONX

Smart Charging Connectors

(1x RJ10 connector, 1x RJ10 splitter, 1x EVBox Charge Point

connector)

EVBox hardware

The following EVBox car charging stations support Smappee Smart EV charging:

Product

Smart Charging compatibility

BusinessLine

Supported from G3 onwards

HomeLine

Supported

Elvi

Supported from Q4 2019 onwards

English –Version 1.2 –January 2021

2. Smappee Smart EV charging

Smappee Infinity ensures autonomous overload protection and optimal charging of the electric vehicle

while it cleverly manages the energy flows so users can live, work, and relax without compromising on

comfort.

Smappee optimises the energy available from solar and other renewable energy sources to ensure it

is maximised throughout the day. It does this while making sure your EV always has as much charge

as you want by the time you need it according to unique Smart Charging schedules.

English –Version 1.2 –January 2021

3. Installation Procedure

The installation procedure consists of the following steps:

Physical installation: the physical installation of the car charging station and all

Smappee Infinity components.

Configuration: the connection between car charging station and Smappee system.

Validation of the installation: checking the connection.

Smart EV charging: the configuration of Smart EV Charging schedules.

This procedure is done with the Smappee Energy Monitor mobile app.

English –Version 1.2 –January 2021

4. Physical installation

WARNING: For safety purposes, it is necessary to power offthe installation before

proceeding with the physical installation.

Smappee physical installation

Install the Smappee Infinity according to the installation manual. Download the installation manual at

smappee.com/smappee-manuals. Do not start the configuration via the app yet!

In order to connect with a car charging station, make sure that:

•At least the following loads are measured with a CT (Check how to configure CTs in

section 5 and 8 of the Smappee Infinity manual).

oGrid

oCar charging station –Appliance

oSolar (if present)

•The Smappee Power Box is installed on the same electrical group as the charging station.

•The phase mapping of the Smappee Infinity is the same as the phase mapping of the

EVBox car charger.

•If you have a preconfigured Smart Charging kit, take notice of the stickers on the CTs

which indicate to which load they should be attached.

IMPORTANT: The following steps assume that the Smappee Infinity physical

installation has been completed. If this is not the case, please follow the

installation manual at smappee.com/smappee-manuals.

English –Version 1.2 –January 2021

In order to enable communication with the EVBox car charging station, a communication cable must

be connected between the Smappee Connect or Genius gateway and the charging station. The

required connectors are supplied in the preconfigured Smart Charging kit, or they can be purchased

separately. The cable itself is not supplied by Smappee. It is recommended to use a RS-485 or CAT 5/6

cable.

Install the communication cable along the route from the Connect or Genius unit to

the charging station. Leave enough cable at each end to make the connections.

Install the RJ10 connector (supplied) on the Connect or Genius unit end of the network

cable:

Note: The unused wires of the network cable remain unconnected. When a Genius

unit is used, connect the RJ10 Splitter (supplied) to the unit.

Connect the RJ10 connector to the RJ10 Splitter or to the Smappee Connect.

Continue with connecting the network cable to the charging station in the next

section.

1 –Do not connect

2 –RS485 –A

3 –RS485 –B

4 –Do not connect

English –Version 1.2 –January 2021

EVBox physical installation

Install the EVBox car charging station according to the EVBox installation manual. Download the

installation manual at evbox.com/en/manuals.

The followingsections describe the connection of the RS485 cable to the followingtypes of charging

station:

•

BusinessLine G3

•

BusinessLine G4

•HomeLine

•Elvi

For each type of charging station, refer to the related Installation Manual for instructions about

removing the cover to access the Smart Charging connection points.

IMPORTANT: The following steps assume that the EVBox car charging station

installation has been completed. If this is not the case, please follow the

installation manual at evbox.com/en/manuals .

English –Version 1.2 –January 2021

BusinessLine G3

In the charging station, find the RS485 connection on the modem board PCB. The

figures below will help you find the connection.

Route the network cable into the charging station along the same route as the power

cable. When the cable enters the base of the station, drill a hole and use a cable

gland.

Connect the network cable to the modem board PCB using the gray 2-pole Phoenix

plug (supplied):

•

Green > RS485 pin A

•

Green/White > RS485 pin B

Otros manuales para Infinity

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Smappee

Smappee

Smappee EV Base Manual de usuario

Smappee

Smappee EV Base Ultra Manual de usuario

Smappee

Smappee EV Base Manual de usuario

Smappee

Smappee EV One Home Manual de usuario

Smappee

Smappee EV One Home Manual de usuario

Smappee

Smappee EV Base Manual de usuario

Smappee

Smappee EV Base Ultra Manual de usuario

Smappee

Smappee EVB-2332-B-E Manual de usuario

Smappee

Smappee EV One Home Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario