Skeye. NANO DRONE Manual de usuario

SKEYE

USER GUIDE

Nano Drone

Idencaon des pièces

SKEYE Nano Drone Remplacer les pales du rotor

Controller

USB Charging Cable

Throle /

Rotate

Direcon Forward/

Backward Sideways

Forward/Backward

Trimmer

Sideways Le/Right

Trimmer

Power Switch (ON/OFF)

Controller Funcons

1. Open the controller

baery cover.

4. Connect the USB charging cable to a USB port. The LED on the USB charging cable

lights red indicang that the baery is charging. When the baery is fully charged,

the LED on the USB charging cable turns o. It takes about 60 minutes to recharge

a discharged baery.

Pushing the throle/rotate sck forward will cause the main rotors to spin. The

farther you push the sck, the faster the rotors will spin, causing the drone to li o

and gain altude.

If you noce that the drone moves forwards or to the side without your touching the

control scks, please adjust the trim of the drone as described in “Trimming”.

Make sure you only charge the rechargeable baery with the supplied

USB charging cable. If you try to charge the rechargeable baery with a

dierent baery charger, this might cause serious damage.

2. Install 2x 1.5V AAA

baeries into the

controller.

3. Lock the baery cover.

WARNING

Baery Installaon

Charging

Flight Controls

Geng Started

Flying Your Drone

Throle Control

Direcon Control

To start or to y higher, push the throle/rotate sck cauously forwards. To land or

y lower, push the throle/rotate sck cauously backwards.

To y the drone forwards or backwards, push the direcon sck cauously to

forwards or backwards.

To y the drone to the le or the right, push the direcon sck cauously to the le

or the right

1. Move the throle/rotate sck to the full down posion.

2. Slide the power switch of the drone. Immediately aer switching the drone

on, place the drone on a at and level surface. The gyro-system will then set itself

automacally.

Advanced Flight: Performing 360° Flips

Sensivity Control

3. Slide the power switch to the ON posion. The controller will emit a tone to

indicate that binding is complete. At the same me, two LED lights on the drone will

start to ash slowly.

4. The controller needs to be calibrated aer successful binding: move the throle/

rotate sck to the full up posion and then push the throle/rotate sck to the full

down posion. When the LED on the controller and the LEDs on the model are all

solid (not blinking), the drone is ready to y.

The drone has three sensivity sengs: low, middle and high.

Press the throle/rotate sck in order to change the sensivity:

1.When the controller emits 1 tone = low sensivity mode.

(sensivity of up to 30%)

2. When the controller emits 2 tones = middle sensivity mode.

(sensivity of up to 50%)

3. When the controller emits 3 tones= high sensivity mode.

(sensivity of up to 70%)

A higher sensivity makes the drone faster and more responsive

The drone can perform 360° front ips, back ips and side ips. Press the direcon

sck to enter ip mode. The controller will emit a tone.

Le Side 360° Flip

Right Side 360° Flip

Forward 360° Flip

Backward 360° Flip

Press the direcon sck and push it to the le once you’ve heard the tone.

Press the direcon sck and push it to the right once you’ve heard the tone.

Press the direcon sckand push it forward once you’ve heard the tone.

Press the direcon sck and push it backward once you’ve heard the tone.

Do not aempt these stunts unl you are able to y condently. Choose

an area that will provide a so landing (carpet or grass) and maintain an

altude of at least 10 feet/3 meter to allow room to recover control as you

pracce ipping the model.

WARNING

Press the direcon sck and push it to the le once you’ve heard the tone.

When hovering, if the drone ies forwards or backwards without you moving the

direcon sck, please proceed as follows:

If the drone moves on its own forwards, press the backward trimmer in steps.

If the drone moves on its own backwards, press the forward trimmer in steps.

When hovering, if the drone ies to the le or right without you moving the direcon

sck, please proceed as follows:

If the drone moves on its own sideways to the le, press the right trimmer in steps.

If the drone moves on its own sideways to the right, press the le trimmer in steps.

Trimming

Direcon Trim

Calibraon

Replacing Rotor Blades

The drone needs to be calibrated if it ies unstable.

1. Place the drone on a at surface and calibrate throle

(See 4 under “Flying Your Drone”)

2. Set the sensivity to high. Keep the throle in the minimum posion.

3. Move the direcon sck to the upper le corner, the throle/rotate sck into

the lower le corner. Two LED lights will start to ash meaning that the calibraon

is successful.

Gently pull the rotor to be replaced from the motor axis. Each rotor is marked with a

“B” or “A”, followed by a number at the underside. Be sure to note the marking and the

lt angle of the rotor blades.

Front le: marking “B”

Front right: marking “A”

Rear le: marking “A”

Rear right: marking “B”

Problem: Controller does

not work.

Cause: The power switch is

turned “OFF”.

Soluon: Turn the power

switch “ON”.

Cause: The baeries have

been wrongly inserted.

Soluon: Check if the

baeries have been

correctly inserted.

Cause: The baeries do

not have enough power.

Soluon: Insert new

baeries.

Problem: The drone cannot

be controlled with the

controller

Cause: The power switch on

the controller is turned “OFF”.

Soluon: First turn the power

switch on the controller “ON”.

Cause: The controller

is possibly not correctly

frequency bound with the

receiver on the drone.

Soluon: Please carry

out the binding procedure

as described in “Flying

Your Drone”.

Problem: The drone does

not li.

Cause: The rotor blades

rotate too slowly.

Soluon: Push the

throle up.

Cause: The baery’s power

is not sucient.

Soluon: Charge the baery

(see chapter “Geng

Started / Charging”).

Problem: During ight, the

Drone loses speed and height

without any obvious reason.

Cause: The baery is

too weak.

Soluon: Charge the baery

(see chapter “Geng

Started / Charging”).

Problem: The drone only

ies in a circle or turns over

on starng.

Cause: Rotor blades

incorrectly ed or damaged.

Soluon: Fit rotor blades /

replace rotor blades

Troubleshoong

Safety Precauons

• Carefully follow the direcons and warnings for this drone and any oponal

support equipment you may use.

• Never operate your drone with low controller baeries.

• The drone has rotang blades that move at high speed, posing danger of damage

and injury. Pilots are responsible for any acons that result in damage or injury

from the improper operaon of the drone. Choose an adequate ying space

without obstacles. Do not operate the drone near buildings, crowds of people,

high voltage power lines, or trees to ensure the safety of yourself, others, and your

drone. Wear eye protecon when operang your drone and keep your hands, face,

hair, loose clothing, and foreign objects away from the rotang blades.

• This drone has small parts that may pose a choking hazard. Keep all small parts and

electrical devices out of the reach of children and animals.

• Pets can become excited by radio-controlled drones. Keep pets away from your

drone at all mes.

• Keep the drone in sight at all mes during operaon and ight. Disconnue

operaon immediately if the drone ies out of your eld of view.

• Because your drone is controlled by radio, it is subject to radio interference

from many sources that are beyond your control. Radio interference can cause

momentary losses of radio control; always allow a safety margin in all direcons

around the drone to prevent collisions.

• When ying indoors, avoid locaons with ceiling fans, hanging light xtures,

heang or air condioning vents, or any other obstacles that may interfere with or

damage your drone.

• Keep hands, hair and loose clothing away from the rotors when the power switch

is turned on.

• Parental guidance is required for younger users.

• The controller and charger are specically designed to charge this drone. Never

use other charging equipment.

• The drone is NOT intended for use by children under fourteen (14) years old,

unless directly supervised by competent adult at all mes.

• Regularly examine the drone and controller for any damage to the plugs,

enclosure, rotors, baery covers and other parts. In the event of any damage,

neither the drone nor the controller should be used.

Tabla de contenidos

Manuales populares de Zumbido de otras marcas

Ryze

Ryze Tello Manual de usuario

PowerVision

PowerVision PowerRay Manual de usuario

Force1

Force1 rogue F72 Manual de usuario

Zerotech

Zerotech DOBBY Manual de usuario

Protocol

Protocol VIDEODRONE AP Manual de usuario

dji

dji Matrice M210 Manual de usuario

MAKE

MAKE Terry Kilby Manual de usuario

SYMA

SYMA X440 Manual de usuario

RUKO

RUKO F11 Manual de usuario

SYMA

SYMA X5UW(720P) Manual de usuario

Dynali

Dynali 25 H Guía

dji

dji PHANTOM 4 Manual de usuario

Atlas

Atlas AtlasPRO Manual de usuario

Twodots

Twodots TVVIN BOARD Manual de usuario

GDU

GDU SAGA Manual de usuario

Ares

Ares ETHOS QX 130 Manual de usuario

Walkera

Walkera ZHUN Manual de usuario

dji

dji WIND-4 Manual de usuario

skeye. NANO DRONE Manual de usuario

Manuales populares de Zumbido de otras marcas