SKC Leland Legacy Manual de usuario

Operating Instructions

Leland Legacy

SKC Inc.

863 Valley View Road

Eighty Four, PA 15330

Form #40075 Rev 0606

Table of Contents

Description ..............................................................................................1

Performance Profile ................................................................................ 2

Pump Setup ............................................................................................ 4

Keypad Basics.............................................................................................................4

Turning the Pump On/Off ............................................................................................4

Entering and Navigating Setup ...................................................................................4

Setup Options..............................................................................................................4

Resetting Run Time Data............................................................................................6

Setting a Sampling Time .............................................................................................6

Setting a DataTrac Program .......................................................................................6

Setting a Delayed Start ...............................................................................................7

Calibration............................................................................................... 8

Resetting Run Time Data............................................................................................8

Setting Pump Flow Rate .............................................................................................8

Verifying Flow Rate Using a Primary Standard Calibrator .........................................9

Verifying Flow Rate Using CalChek Automatic Calibration Feature ........................10

Sampling ...............................................................................................16

Scrolling Through Data .............................................................................................16

Resetting Run Time Data..........................................................................................16

Deleting a DataTrac Program or Delayed Start........................................................17

Deleting a Sampling Time .........................................................................................17

Flow Fault ..................................................................................................................17

Battery Operation.................................................................................. 18

Installing Battery Pack...............................................................................................18

Battery Status ............................................................................................................19

Low Battery Fault ......................................................................................................19

Charging the Battery................................................................................................19

Charger Status ..........................................................................................................20

Removing and Replacing the Battery Pack ..............................................................20

Programming the Pump Using a PC .................................................... 22

Optional Accessories ............................................................................23

Service Policy .......................................................................................24

Warranty ...............................................................................................25

Indicates a reminder or note.

Indicates a warning or caution.

Notice: This operating instruction may not address all safety concerns (if any) associated with this

product and its use. The user is responsible for determining and following the appropriate safety and

health practices and regulatory limitations (if any) before using the product. The information contained in

this document should not be construed as legal advice, opinion, or as a final authority on legal or

regulatory procedures.

Leland Legacy Quick Guide

Terms »

Star button

✹

•Scrolls through run time data and Setup options

Up and down arrow buttons

▲ ▼

•Toggle between display choices and increase or decrease sampling parameters in Setup

Button sequence

▼

✹

= press buttons individually

[

▲▼

] = press simultaneously

✹▲▼✹

= security code, always press in sequence

Security code

✹▲▼✹

•Prevents unauthorized changes to the pump’s sampling program.

Programming Sequences »

•To activate pump (e.g., to change pump from Sleep to Hold):

Press any button.

•To change pump from Hold to Run or Run to Hold:

Press [

▲▼

•To reset accumulated data:

Press [

▲▼

] then

✹▲▼✹

. Press

✹

til

CLr

splays then press [

▲▼

];press

✹

until

End

displays then press

[

▲▼

•To set pump flow rate:

Press [

▲▼

], then

✹▲▼✹

. Flow rate and SET flash.Press

▲

▼

to change flow rate.Press

✹

until

End

appears then press [

▲▼

] to save setting and place pump in Hold.

•To calibrate flow rate with standard calibrator:

Press [

▲▼

], then

✹▲▼✹

. Flow rate and SET flash.Press

▲

▼

to change flow rate.Press

✹

once.

ADJ

displays. Press

▲

▼

until desired flow rate is indicated on calibrator.When finished, press

✹

until

End

displays, then press [

▲▼

] to save new setting and place pump in

Hold.For CalChek Calibration, see operating

instructions.

•To change temperature scale from F to C or C to F:

Press [

▲▼

] then

✹▲▼✹

. Press

✹

until temperature displays.Press

▲

▼

to switch units;press

✹

until

End

displays then press [

▲▼

] to save new setting.

•To change atmospheric pressure scale (mm, mb, In):

Press [

▲▼

] then

✹▲▼✹

. Press

✹

until pressure displays then press

▲

▼

to switch units;press

✹

until

End

displays then press [

▲▼

] to save new setting.

•To change time scale (12 Hr/24 Hr/Dela):

Press [

▲▼

] then

✹▲▼✹

. Press

✹

until 12 Hr, 24 Hr, or Dela displays then press

▲

▼

to switch units;press

✹

until

End

displays then press [

▲▼

] to save new setting.

To set delayed start (Dela), see operating instructions.

•To change clock:

Press [

▲▼

] then

✹▲▼✹

. Press

✹

until clock displays then press

▲

▼

to change flashing hour; press

✹

move to minutes and

▲

▼

to change setting.Press

✹

until

End

displays then press [

▲▼

] to save new

setting.

•To change the sampling time function:

Press [

▲▼

] then

✹▲▼✹

. Press

✹

until

ST L/min

displays then press

▲

to change flashing digit; press

✹

until

End

displays then press [

▲▼

] to save new setting.To delete, follow above steps and press

▼

until 0 appears.

Exit Setup.

Note:When in Setup, choosing Esc instead of End will exit Setup without saving new settings.

SKC Inc., 863 Valley View Road, Eighty Four, PA 15330 • www.skcinc.com

Inlet Port

with protective filter

Soft Rubber

Over-molding

protects against

damage

Liquid

Crystal

Display

(LCD)

Keypad

with large

operating

buttons

Flashing LED

Run Indicator

Li-Ion

Battery

Pack

for 24-hour

run times

(included)

Battery

Status

Icon

Not shown:

Beltclip (back)

Battery Charging

Jack (top)

Computer Interface

Port (top)

The Leland Legacy dual diaphragm sample pump is designed specifically to

provide constant airflows from 5 to 15 L/min with minimum power require-

ments and low noise. Diaphragm and valve design minimizes power require-

ments and reduces noise. Incoming and outgoing airflow is pulsation damp-

ened. The lightweight Leland Legacy is housed in a thermoplastic material for

strength and features an over-molding of soft rubber that protects against dam-

age and reduces noise. Powered by a rechargeable battery pack containing 10

Li-Ion cells, the Leland Legacy provides 24-hour run times for 10 L/min at 12

inches water back pressure. The pump’s patented internal flow sensor mea-

sures flow directly and acts as a secondary standard, constantly maintaining

the set flow rate. Built-in sensors automatically correct flow for variations in

temperature and atmospheric pressure. Advanced programming features are

available when used with a PC and DataTrac Software.

Leland Legacy Sample Pump

Description

FlowFlow Range: 5 to 15 L/min

Flow Control System: Closed loop with patented* internal flow sensor

Compensation Range: 15 L/min at 5 inches water back pressure

10 L/min at 12 inches water back pressure

5 L/min at 20 inches water back pressure

Accuracy: ±3% of set-point after calibration to desired flow

Flow Fault: If flow drops by more than 5%, pump stops and

holds historical data. Auto-restart will attempt restart

every 20 sec up to 10 times.

Adjustable with DataTrac

Software. See p. 16.

Operation

Display: LCD, displays pump serial number, pump software

revision level, flow rate, volume, temperature, atmo-

spheric pressure, time of day, run time, and pump status,

i.e., hold and run as well as Setup information.

Volume Display: Continually updated, based on corrected flow rate

multiplied by sampling time

Time Display: Time of day in hours and minutes (12- or 24-hour clock)

with AM and PM indicators

Timer Display Range: 1 to 99999 minutes (69 days). If the run time exceeds 69

days, the timer display rolls over.

Timing Accuracy: 1 min/month @ 25 C

Atmospheric Pressure

Accuracy: ±0.3 inches Hg

OperatingTemp. Range: 32 to 113 F (0 to 45 C)

Protectsamplepumpfromweatherwhenin

use outdoors.

Typical Run Time†:Sioutas Impactor (13 in water bp): 24 hrs at 9 L/min

PEM with 37-mm, 2.0 µm PTFE filter #225-1709‡: 24 hrs

at 10 L/min

Low Volume PUF Tube: 24 hrs at 5 L/min

DPS Sampler: 24 hrs at 10 L/min

MCE filter, 37 mm, 0.8 µm: >10 hrs at 9 L/min

Noise Level: 64.1 dBA - pump without case

55.7 dBA - pump housed in noise-reducing case

(optional accessory Cat. No. 224-89, see p. 20)

Measured 3 ft (1m) distance from pump operating at

10 L/min and 12 inches water back pressure

User-adjustable Values: Sample run time, calibration, clock display, flow rate,

time of day, delayed start, and temperature and

atmospheric pressure display

Recorded Values: Start date and time, stop date and time, total sample

time, flow rate, sample volume, temperature, atmo-

spheric pressure, and pump mode transitions

Performance Profile

Adjustable Logging: Records pump history from 3 seconds (15.4 min. of

data)

Interval: up to 8 hours (over 102 days of data) depending on

setting.

Option available when using DataTrac

Software.

Power

Power Supply: Removable, rechargeable lithium-ion (Li-Ion) battery

pack (

See Li-Ion Battery Shipment below

), 7.2 V x 10 Ah

Charger/AC adapter: input voltage 100 to 240 V AC

Battery RechargeTime: 15 hours

ChargingTemp. Range: 32 to 113 F (0 to 45 C)

StorageTemp. Range: -4 to 113 F (-20 to 45 C)

Physical

Size: 8 x 3.9 x 2.6 inches (20 x 10 x 7 cm)

Weight: 36 oz (1 kg)

Case: Thermoplastic with soft rubber over-molding

Approvals CE marked, UL and cUL (pending),

ATEX (pending)

* U.S. Patent No. 5,892,160

† Results when tested with a new pump and new fully charged battery.Pump performance may vary.

‡ Back pressure on Teflon filters can vary within the same lot.

Li-Ion Battery Shipment

Rechargeable, lithium-Ion batteries for use with SKC sampling pumps have been

tested in accordance with the UN manual of Tests and Criteria and are designated

as UN3091.

For air shipments:

Rechargeable lithium-Ion batteries in SKC pumps are subject to the A-45 exemption

to the IATA regulations and are not regulated for air shipments.This information must

be written on the shipping document when shipping by air.

For ground shipments:

US DOT regulations specify a limit of 24 or fewer battery cells in one shipping box. If

you exceed 2 Leland Legacy pumps with battery packs in one shipping box, specific

shipping requirements must be followed. Contact SKC for more information or refer

to the regulatory authority in your area.

Intrinsic safety and other approvals are void if SKC pumps are not

repaired by SKC or authorized SKC repair centers. Use only SKC-

approvedparts toensurereliable performanceandintrinsic safetyand

to maintain the SKC warranty.

Performance Profile

Keypad Basics

✹Scrolls through run time data

and Setup options.

▲Increases values such as flow

rate.

▼Decreases values such as

flow rate.

[▲▼]When pressed simulta-

neously, displayed item is

selected or entered.

✹▲▼✹ Security code that must be

pressed in sequence to enter

Setup.

Turning the Pump On/Off

•Press any button to turn on the power.

•Press [▲▼] to run the pump or to place a running pump in Hold.

•Manual Off: from Hold, press and hold ✹.

•Auto Off turns off the pump after 5 minutes in Hold.

Entering and Navigating Setup

Entering: Press [▲▼], then press the security code in

sequence ✹▲▼✹. Setup should appear

briefly on the LCD.

Navigating: Press ✹to scroll through parameters. Once

the LCD shows End, parameters will repeat

until the user exits Setup.

Exiting: Press ✹ until End appears on the LCD. Press

[▲▼]. The pump is now in Hold.

Setup Options

After entering Setup, go to:

1. Flow Set: Press ▲or ▼to increase or decrease pump

flow rate. Pump will start running. Press ✹to move to

next parameter.

2. ADJ: Used during calibration with primary standard

calibrator (not for use with CalChek feature). Press ▲or

▼to increase or decrease flow adjustment until desired

flow is indicated on calibrator. Press ✹until End

appears. Press [▲▼] to save new flow and adjustment

settings and exit Setup.

▼Down

arrow

button

✹

Button

▲Up

arrow

button

Pump Setup

If changing other parameters, continue pressing ✹after End

appears and the remainder of the menu items will appear. Once all

changes are entered, press ✹until End appears, then press [▲▼] to

save new settings and exit Setup. Pressing [▲▼] when Esc appears

will exit Setup without saving new settings.

3. CALCh: Use for CalChek calibration feature only.

Pressing [▲▼] initiates single-point calibration.

Pressing ▲seven times initiates a full calibration. See

CalChek Calibration instructions on pp. 9 to 14.

4. 12 Hr/24 Hr Clock and Delayed Start (factory

default is 12 Hr clock): Press ▲or ▼to move

between standard (12 hour), military (24 hour), and

Dela (delayed start). Press ✹to select. If Dela (delayed

start) is selected, follow instructions on p. 7.

5. Time of day: Press ▲or ▼to increase or decrease

flashing hour. Press ✹to move from hours to

minutes. Press ▲or ▼to increase or decrease

flashing minutes. Press ✹to move to next parameter.

6. ST (Sampling Time): Allows the user to program a

specific run time. Press ▲or ▼to increase or

decrease the time in minutes (up to 99999 minutes).

Press ✹to move to next parameter. See pp. 6 and 16 for

Setting and Deleting a Sampling Time.

7. Temperature (factory default is Celsius): Press ▲

or ▼to toggle between Fahrenheit (F) and Celsius

(C). Press ✹to move to next parameter.

8. Atmospheric Pressure (factory default is mm): Press

▲or ▼to toggle between inches of mercury (In),

millibars (mb), and millimeters of mercury (mm).

Press ✹to move to next parameter.

9. CLr: Press [▲▼] to clear accumulated run time and

volume data to zero (see Resetting Run Time Data on

p. 6).

Pump Setup

10. ESC: Press [▲▼] to exit Setup without saving new

settings.

11. End: Press [▲▼] to save new settings and exit Setup.

PrOFF: Appears only when a program is loaded into pump memory. See

DataTrac Software Operating Instructions (Form #40085) for setting a

program. See p. 16 for Deleting a DataTrac Program or Delayed Start.

Resetting Run Time Data

To reset accumulated volume and run time data to zero:

1. Press [▲▼], then press the security code in sequence ✹▲▼✹. Setup

will display briefly.

2. Press ✹until Clr appears, then press [▲▼].

3. Press ✹until End appears, then press [▲▼] to exit Setup. The pump is

now in Hold.

CLr does not clear previously set sampling time (ST). See Deleting a

Sampling Time on p. 16.

Setting a SamplingTime (ST)

Program the Leland Legacy from the integral keypad or a PC using DataTrac

software to sample from 1 to 99999 minutes.

1. Press [▲▼], then press the security code in sequence

✹▲▼✹. Setup will display briefly.

2. Repeatedly press ✹until ST L/min and a flashing time

and Set appear on the display.

3. Set the sampling time by pressing ▲ or ▼to increase

or decrease it to the desired time in minutes.

4. Press ✹repeatedly until End appears.

5. Press [▲▼] to save the new sampling time and exit

Setup.

6. Press [▲▼] to begin sampling. The time display will

count down in seconds and the pump will go to Hold.

The total sampling time will display.

7. To delete a set sampling time, see Deleting a Sampling

Time on p. 16.

Setting a DataTrac Program

See DataTrac for Leland Legacy Software Operating Instructions (included on

software CD).

Pump Setup

Setting a Delayed Start

A delayed start can be programmed using the pump

keypad or from a PC using DataTrac Software. The

following instructions are for keypad only. See DataTrac

Operating Instructions (included on software CD) for

programming from a PC.

When setting the pump for sampling from 1 to 99999

minutes to begin within the next 12-hour period, follow

this procedure:

1. Press [▲▼], then press the security code in sequence

✹▲▼✹. Setup will display briefly.

2. Press ✹until the display reaches the 12 Hr/24 Hr clock. If delayed

start is already programmed, the display will show Dela (delayed

start) in place of 12 Hr. If no delay is programmed, press ▲ or ▼ until

the display shows a flashing Dela (delayed start).

3. Press ✹until the time of day (flashing hours) displays. Select the hour

(time of day) that the pump is to begin sampling (within the next 12

hours) by pressing ▲ or ▼ until the desired hour displays. Press ✹and

the minutes will flash. Press ▲ or ▼ until the desired minutes display.

The time of day entered will be the next occurrence of this time

within the next 12-hr period after the delayed start is entered.

There is no a.m. or p.m. designation.

4. Press ✹until the ST displays. Press ▲ or ▼ to set the

desired run time in minutes. A delayed start cannot

be run unless a sampling time (ST) is programmed.

5. Press ✹until End appears.

6. Press [▲▼] to save settings and exit Setup.

7. Prog and a flashing Hold will appear in the upper

left corner of the display. The pump is now set for

delayed start.

Once a program is set in the pump, the pump cannot be run

manually. To return to manual pump operation, let the program

run its course or delete the program (see Deleting a DataTrac

Program or Delayed Start on p. 16).

Display for

delayed start

Pump Setup

Otros manuales para Leland Legacy

Tabla de contenidos

Otros manuales de Bomba de agua de SKC

SKC

SKC Leland Legacy Manual de usuario

SKC

SKC TOUCH Instrucciones de funcionamiento

SKC

SKC 224-50MH Manual de usuario

SKC

SKC AirLite 110-100 Manual de usuario

SKC

SKC AirChek 3000 Manual de usuario

SKC

SKC AirChek TOUCH 220 Series Manual de usuario

SKC

SKC AirChek 52 Manual de usuario

SKC

SKC AirChek 52 Manual de usuario

SKC

SKC 224-44XR Manual de usuario

SKC

SKC AirChek2000 Manual de usuario

SKC

SKC AirChek Connect Manual de usuario

SKC

SKC AirChek XR5000 Manual de usuario

SKC

SKC AirChek XR5000 Manual de usuario

SKC

SKC 220 Series Manual de usuario

SKC

SKC AirLite 110-100-T Manual de usuario

SKC

SKC 224-44XR Manual de usuario

SKC

SKC BioLite Plus 228-9620 Manual de usuario

SKC

SKC 224-PCXR4 Manual de usuario

SKC

SKC QuickTake 30 Manual de usuario

SKC

SKC AirChek XR5000 Manual de usuario

SKC

SKC Leland Legacy Manual de usuario

SKC

SKC 224-PCMTX8 Manual de usuario

SKC

SKC AirChek 220-3100 Manual de usuario

SKC

SKC 210-1000 Series Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario