SKAARHOJ Atem TCP Link Manual de usuario

SKAARHOJ DEVICE CORES

SKAARHOJ Atem TCP Link

The ATEM TCP Link establishes a connection to an ATEM switcher for programs and devices without

native ATEM protocol support.

SKAARHOJ DEVICE CORES
Introduction 3
Update December 2020 3
Update May 2020 3
Update January 2020 3
Known Limitations 3
Port Information 3
Set Up 4
Firmware Updater 4
Shipping Conﬁguration 4
Changing IP Information 5
Conﬁrm Connection 5
Establishing a Telnet Connection 6
Controlling You ATEM 7
Extract of ATEM-TCP Link Commands 7
Command Structure Examples 10
Updating Firmware 12
Finding the Latest Firmware 12
Load Firmware from File 12
Change Log 13
Troubleshooting 14
Error on Check: Your controller is not yet registered 14
Controller does not show up under Port in Firmware Application 14
Network Recommendations 16
Facts 16
Power over Ethernet (PoE) Speciﬁcations 16
Troubleshooting 16
WEEE Information 17
2

SKAARHOJ DEVICE CORES

Introduction

A larger number of functions on the ATEM series of switchers can be controlled from a SKAARHOJ ATEM

TCP Link and we have integrated with the ATEM switchers for a long time.

When using the ATEM TCP Link one can connect to the ATEM Switcher directly without the need of

running ATEM Software Control Panel on your computer. But you can, and any change made either way

will be reﬂected on each device.

You can connect to a single ATEM Switcher from a single SKAARHOJ ATEM TCP Link but limitations apply.

The different ATEM Switchers varies in how many clients can be connected at the same time. For details

see https://www.youtube.com/watch?v=ApYouYfX5G4

Theoretically, up to 7 clients can be connected to the ATEM TCP Link simultaneously.

Please notice the ATEM Switchers are very picky as to latency for connected clients. Ensure a stable and

fast network. If using VPN or other long distance network solutions latency may be too high and

connection will not be established.

Update December 2020

With the release of ATEM2TCP Firmware v1.5.5 we now support recording and streaming for the Atem

Mini and Atem Mini Pro.

Update May 2020

After the release of the ATEM Mini and ATEM Mini Pro, we can conﬁrm that our current ATEM2TCP Link

ﬁrmware is able to control the base functions of the ATEM Mini series but we have not yet implemented

full support for the ATEM Mini series with our ATEM TCP Link.

Update January 2020

With release of ATEM2TCP Firmware v1.5 we now have support for ATEM 8.1 and the ATEM Constellation.

Known Limitations

- Audio control has not yet been fully implemented on the Atem TCP Link.

- Atem Mini and Atem Mini Pro support has not yet been fully implemented.

- For the ATEM-TCP Link on AVR control of ME3 and ME4 is not possible due to memory restrictions. On

the Due it works.

- Please note that not all commands are meant to change a parameter on an Atem switcher, some are for

the return of the current status.

Port Information

Protocol

Listening Port

Destination Port

TCP

8899

9910

SKAARHOJ DEVICE CORES

Set Up

Firmware Updater

You won’t get far without the SKAARHOJ Firmware Updater application. Download it www.skaarhoj.com/

support/ﬁrmware-updater/. Install, run it and connect your controller. Please notice the USB cable is only

to be used for conﬁguration and ﬁrmware upgrade. The USB plug is not designed to be connected during

normal operation. More details are found in the “Firmware Updater Application” section of Installation and

Operations Manual at “https://www.skaarhoj.com/support/manuals/".

Shipping Conﬁguration

The ATEM-TCP Link ships with the following IP settings

•ATEM-TCP Link IP: 192.168.10.99

•Subnet: 255.255.255.0

•Gateway: 192.168.10.1

•ATEM IP: 192.168.10.240

These settings can be conﬁrmed and changed by the use of our!Firmware Updater Application!via the

commands listed in the section “Changing IP Information”. Do!not!use any features from the Firmware

Updater!besides!the Serial Monitor. Pressing “Update Firmware" will render the ﬁrmware on the ATEM-

TCP Link unusable and require reloading the ﬁrmware. Please see the “Troubleshooting” section of this

manual for more information if you pressed “Update Firmware”.

Commands to/from the ATEM-TCP Link are not done from the Serial Monitor but by establishing a telnet

connection to the device. Please see the section "Establishing Telnet Connection”.

Connect the SKAARHOJ controller to your

computer with the included USB cable. The device

shows up in the Port list. Only connect one

SKAARHOJ controller at a time.

SKAARHOJ DEVICE CORES

Changing IP Information

The IP information for the ATEM-TCP Link can be changed by entering the following commands in the

Serial Monitor. You will need to restart the device for changes to take effect.

Device IP Address

•ip=A.B.C.D

ATEM IP Address

•atem=A.B.C.D

Gateway and Subnet

•subnet=A.B.C.D

•gateway=A.B.C.D

Conﬁrm Connection

When a SKAARHOJ controller have successfully connected to the ATEM the serial monitor will report:

ATEM has initialized

Connection to ATEM Switcher established!

If the SKAARHOJ controller is unable to locate the ATEM the network the serial monitor will report:

.Connection to ATEM Switcher has timed out - reconnecting!

Continuously connecting to ATEM switcher on IP 192.168.10.240

SKAARHOJ DEVICE CORES

Establishing a Telnet Connection

A Telnet connection can be established from Terminal on a Mac or Command Prompt on a Windows

computer.

In order to establish a Telnet connection use the port 8899 and the IP address of the ATEM-TCP Link

entered into Terminal or Command

•telnet 192.168.10.99 8899

•nc 192.168.10.99 8899 (some versions of Mac OS do not have telnet, us “nc” instead)

!Check the connection by making a CUT or similar action on the ATEM in order to verify you receive state

changes.

On the ATEM-TCP Link Auto negotiation is turned off and default interface is set to 100 mbit full duplex.

Enabling Telnet on Windows Computers

Please note, Telnet is not enable by default on windows computers. If when trying to establish a Telnet

connection from Command Prompt you receive the error “Telnet is not recognized as an internal or

external command, operable program or batch ﬁle.” you will need to enable Telnet under “Turn Windows

Features On or Off”.

Establish Connection

Test Connection

Windows- Command Prompt

Establish Connection

Test Connection

Mac-Terminal

SKAARHOJ DEVICE CORES

Controlling You ATEM

Extract of ATEM-TCP Link Commands

This list is only of the base command, you will need to test using your Atem to discover the individual

parameters of each command.

Items marked in Blue only feedback the current state of the ATEM.

Item marked in Red are currently not working or feedback incorrectly.

AtemConnected,

!InputLongName,

!InputShortName,

!InputAvailability,

!InputMEAvailability,

!MultiViewerInputVideoSource,

!ProgramInputVideoSource,

!PreviewInputVideoSource,

!TransitionStyle,

!TransitionNextTransition,

!TransitionStyleNext,

!TransitionNextTransitionNext,

!TransitionInTransition,

!TransitionFramesRemaining,

!TransitionPosition,

!TransitionMixRate,

!TransitionDipRate,

!TransitionDipInput,

!TransitionWipeRate,

!TransitionWipePattern,

!TransitionWipeWidth,

!TransitionWipeFillSource,

!TransitionWipeSymmetry,

!TransitionWipeSoftness,

!TransitionWipePositionX,

!TransitionWipePositionY,

!TransitionWipeReverse,

!TransitionWipeFlipFlop,

!TransitionDVERate,

!TransitionDVEStyle,

!TransitionDVEFillSource,

!TransitionDVEKeySource,

!TransitionDVEEnableKey,

!TransitionDVEPreMultiplied,

!TransitionDVEClip,

!TransitionDVEGain,

!TransitionDVEInvertKey,

!TransitionDVEReverse,

!TransitionDVEFlipFlop,

!KeyerOnAirEnabled,

!KeyerType,

!KeyerFlyEnabled,

!KeyerFillSource,

!KeyerKeySource,

!KeyerMasked,

!KeyerTop,

!KeyerBottom,

!KeyerLeft,

!KeyerRight,

!KeyDVESizeX,

!KeyDVESizeY,

!KeyDVEPositionX,

!KeyDVEPositionY,

!KeyDVERotation,

!KeyDVEBorderEnabled,

!KeyDVEShadow,

!KeyDVEBorderBevel,

!KeyDVEBorderOuterWidth,

!KeyDVEBorderInnerWidth,

!KeyDVEBorderOuterSoftness,

!KeyDVEBorderInnerSoftness,

!KeyDVEBorderBevelSoftness,

SKAARHOJ DEVICE CORES

!KeyDVEBorderBevelPosition,

!KeyDVEBorderOpacity,

!KeyDVEBorderHue,

!KeyDVEBorderSaturation,

!KeyDVEBorderLuma,

!KeyDVELightSourceDirection,

!KeyDVELightSourceAltitude,

!KeyDVEMasked,

!KeyDVETop,

!KeyDVEBottom,

!KeyDVELeft,

!KeyDVERight,

!KeyDVERate,

!DownstreamKeyerFillSource,

!DownstreamKeyerKeySource,

!DownstreamKeyerTie,

!DownstreamKeyerRate,

!DownstreamKeyerPreMultiplied,

!DownstreamKeyerClip,

!DownstreamKeyerGain,

!DownstreamKeyerInvertKey,

!DownstreamKeyerMasked,

!DownstreamKeyerTop,

!DownstreamKeyerBottom,

!DownstreamKeyerLeft,

!DownstreamKeyerRight,

!DownstreamKeyerOnAir,

!DownstreamKeyerInTransition,

!DownstreamKeyerIsAutoTransitioning,

!DownstreamKeyerFramesRemaining,

!FadeToBlackRate,

!FadeToBlackStateFullyBlack,

!FadeToBlackStateInTransition,

!FadeToBlackStateFramesRemaining,

!AuxSourceInput,

!CameraControlIris,

!CameraControlIrisf,

!CameraControlFocus,

!CameraControlGain,

!CameraControlWhiteBalance,

!CameraControlSharpeningLevel,

!CameraControlZoomNormalized,

!CameraControlZoomSpeed,

!CameraControlColorbars,

!CameraControlLiftR,

!CameraControlGammaR,

!CameraControlGainR,

!CameraControlLumMix,

!CameraControlHue,

!CameraControlShutter,

!CameraControlLiftG,

!CameraControlGammaG,

!CameraControlGainG,

!CameraControlContrast,

!CameraControlSaturation,

!CameraControlLiftB,

!CameraControlGammaB,

!CameraControlGainB,

!CameraControlLiftY,

!CameraControlGammaY,

!CameraControlGainY,

!MediaPlayerSourceType,

!MediaPlayerSourceStillIndex,

!MediaPlayerSourceClipIndex,

!MediaPlayerStillFilesIsUsed,

!MediaPlayerStillFilesFileName,

!MacroRunStatusState,

!MacroRunStatusIsLooping,

!MacroRunStatusIndex,

!MacroPropertiesIsUsed,

!MacroPropertiesName,

!SuperSourceFillSource,

SKAARHOJ DEVICE CORES

!SuperSourceKeySource,

!SuperSourceForeground,

!SuperSourcePreMultiplied,

!SuperSourceClip,

!SuperSourceGain,

!SuperSourceInvertKey,

!SuperSourceBorderEnabled,

!SuperSourceBorderBevel,

!SuperSourceBorderOuterWidth,

!SuperSourceBorderInnerWidth,

!SuperSourceBorderOuterSoftness,

!SuperSourceBorderInnerSoftness,

!SuperSourceBorderBevelSoftness,

!SuperSourceBorderBevelPosition,

!SuperSourceBorderHue,

!SuperSourceBorderSaturation,

!SuperSourceBorderLuma,

!SuperSourceLightSourceDirection,

!SuperSourceLightSourceAltitude,

!SuperSourceBoxParametersEnabled,

!SuperSourceBoxParametersInputSource,

!SuperSourceBoxParametersPositionX,

!SuperSourceBoxParametersPositionY,

!SuperSourceBoxParametersSize,

!SuperSourceBoxParametersCropped,

!SuperSourceBoxParametersCropTop,

!SuperSourceBoxParametersCropBottom,

!SuperSourceBoxParametersCropLeft,

!SuperSourceBoxParametersCropRight,

!AudioMixerInputMixOption,

!AudioMixerInputVolume,

!AudioMixerInputBalance,

!AudioMixerMasterVolume,

!AudioMixerMonitorMonitorAudio,

!AudioMixerMonitorVolume,

!AudioMixerMonitorMute,

!AudioMixerMonitorSolo,

!AudioMixerMonitorSoloInput,

!AudioMixerMonitorDim,

!AudioMixerLevelsSources,

!AudioMixerLevelsMasterLeft,

!AudioMixerLevelsMasterRight,

!AudioMixerLevelsMasterPeakLeft,

!AudioMixerLevelsMasterPeakRight,

!AudioMixerLevelsMonitor,

!AudioMixerLevelsSourceOrder,

!AudioMixerLevelsSourceLeft,

!AudioMixerLevelsSourceRight,

!AudioMixerLevelsSourcePeakLeft,

!AudioMixerLevelsSourcePeakRight,

!AudioMixerTallySources,

!AudioMixerTallyAudioSource,

!AudioMixerTallyIsMixedIn,

!TallyBySourceSources,

!TallyBySourceVideoSource,

!TallyBySourceTallyFlags,

!performCutME,

!performAutoME,

!performDownstreamKeyerAutoKeyer,

!performFadeToBlackME,

!CameraControlAutoFocus,

!CameraControlAutoIris,

!CameraControlResetAll,

!MacroAction,

!MacroRunChangePropertiesLooping,

!AudioLevelsEnable,

RecordingStatus,

StreamingStatus,

dumpState,

SKAARHOJ DEVICE CORES

Command Structure Examples

For detailed reference please see: https://www.skaarhoj.com/ﬁleadmin/BMDPROTOCOL.html

The correct syntax for a Cut on 1 M/E is:

•performCutME:0=1

The correct syntax for a Cut on 2 M/E is:

•performCutME:1=1

The correct syntax for a Auto Transition on 1 M/E is:

•performAutoME:0=1

The correct syntax for a Auto Transition on 2 M/E is:

•performAutoME:1=1

The correct syntax for starting macro playback is:

•MacroAction:1=0

Where 1 in this case is macro number 2, as the numbering starts from 0. The number 0 is a parameter

meaning ”Run Macro", where the following different parameters are available for this particular command.

If you wanted to stop macro playback, you would send 1 as the parameter, and hexadecimal 0xFFFF as

the index, which is 65535 in decimal, so that the command would be

•MacroAction:65535=1

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario