SIRS-E Pilotino CRMX PCB Manual de usuario
E518483
INDEX
1. Introduction
2. Safety Information
3. Specification Characteristics
4. Onboard Features (Nomenclature)
5. Mechanical Details
6. Installation
6.1 Rx Mode Installation
6.1.1 Basic Connections
6.1.2 Daisy Chain
6.2 Tx Mode Installation
6.2.1 Basic Connections
6.2.2 Daisy Chain
6.3 Stand Alone Mode Installation
6.3.1 Basic Connection (Rx Mode)
6.3.2 Daisy Chain (Rx Mode)
6.3.3 Basic Connection (Tx Mode)
6.3.4 Daisy Chain (Tx Mode)
7. Rx or Tx Mode Selection
7.1 By Ios or Android App
7.2 By Pairing Button
8. Connecting Device (Rx) to Timo Two
9. Connecting Device (Tx) to other P CRMX™ PCB
ILOTINO
10. Mode LEDs Indicator
10.1 Rx Mode
10.2 Tx Mode
11. Antenna Specifications
UL Certificate
2
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
Pg. 3
Pg. 4
Pg. 4
Pg. 5
Pg. 6
Pg. 7
Pg. 8
Pg. 8
Pg. 9
Pg. 10
Pg. 10
Pg. 11
Pg. 12
Pg. 12
Pg. 13
Pg. 14
Pg. 15
Pg. 16
Pg. 16
Pg. 16
Pg. 17
Pg. 17
Pg. 18
Pg. 18
Pg. 18
Pg. 19
Pg. 20
1. Introduction
One of the most important features of this product involves the onboard IO socket. This socket is
meant to be used with the P ™ PCB
ILOTINO with onboard CRMX (wireless DMX) capabilities. With
the CRMX modules, you instantly convert P ™ PCB into a Wireless DMX RDM.
ILOTINO
Allowing the user to easily integrate it into any project
Key Features: P CRMX™ PCB
ILOTINO
Compatible with any CRMX Device
Robust Wireless Signal
RDM Compatible
Onboard IO socket for quick integration
Wire to Board Quick Connectors
Plug and Play with Onboard IO Socket
5 Year Limited Warranty
Made in Italy
UL Recognized
Check our YouTube Video!
The P CRMX™ PCB
ILOTINO is the newest addition to the LED CV DMX decoder family for SIRS-E. Control any
kind of CV LED Strip, COB, and other constant voltage LED products. This version of the P ™ comes
ILOTINO
in a bare PCB format. This product is intended to be embedded into custom fixtures and lighting control
systems in which component size is critical. Equipped with four mounting holes, the P CRMX™ PCB is
ILOTINO
ready to be installed with M2.5 X 5mm stand-offs into any sort of enclosure.
R
P CRMX™ PCB
ILOTINO
3
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved
E518483
Package Contents
+ PILOTINO™ CRMX PCB - : Pilotino-CRMXSKU
+ u.FL to Female SMA Coax Cable (10 cm)
+ Dipole Tilt Swivel Antenna
P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
Check our page
2. Safety Information
Safety Information
3 Specification Characteristics .
The exposed CRMX design of this product results in a major reduction in its foot print. With a slim and narrow design, this
configuration is intended to be used in applications that would benefit from this feature. Some examples of applications
include: fixture integration, custom control enclosures, and others. The exposed design comes with few precautions to
take notice of.
The is a non-waterproof device with an IP 20 rating. Keep the unit dry at all times and away from P CRMX™ PCB
ILOTINO
liquids and humid environments. Make all connections to the LEDs and driver prior to powering on the circuit. All lead
voltage connections to the drivers must be performed by a licensed electrician. Do not touch any of the surfaces of the
device once the unit is powered on. Ensure that all connections are secure and eliminate all possibilities of shorting the
unit. Use the proper wire gauge for the wire to board connections. We recommend using 18 awg stranded wire for the
power input, and the DMX daisy chain connection. Do not mount the unit where vibrations or shock are present.
Power Consumption: 40mA in receiver mode
Power Consumption: 250mA in transmitter mode
DMX window funtionality
Working Humidity: 0% - 90% non-condensing
IP Rating: IP 20 Non-waterproof (Keep dry)
Ventilation: Do not install in airtight spaces
Bluetooth Supported
Key Features
Working Voltage: 5V DC
Input Control Protocol: DMX512-A
RDM: Yes
CRMX: Lumen Radio with Timo Module
Hardware Specifications
Working Ambient Temp: - + 4
10 °C 5 °C
Antenna: RP-TNC male
Dimensions mm (L W H): 68 22.3 11.4
4
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
4. Onboard Features
1
44
442
3
6
5
7
1. I/O Connection Socket + DMX out (For PILOTINO™ PCB)
2. wire to board quick connectorsI/O
3. Dip Switches to set the DMX termination line
4. Mounting holes for Standoffs M2.5 (metric)
5. Pairing button for bluetooth connections
6. Mode Indicator LED
7. to connect a Antennau.FL connector receiving or transmitting
5
5
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
5. Mechanical Details
15.84mm
Top ViewP CRMX™ PCB
ILOTINO
22.2 mm5
68.00mm
16.00mm
49 50. mm
16 25. mm
Side ViewP CRMX™ PCB
ILOTINO
6
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
6 Installation.
Standoffs
Four 2.5M x 5mm standoffs should be used to properly mount the unit onto a smooth and level surface. It is recommended
that the included factory 2.5M stand offs be used. To fasten the onto a surface, first screw the four P CRMX™ PCB
ILOTINO
screws in a crisscross pattern. To tighten the screws, torqued them down to ¼ turn past hand tight, again in a crisscross
pattern. Always tighten the screw opposite to the last screw that was torqued down. Do not over tighten the screws as doing so
will result in damage to the device.
Clearance
Due to the exposed contact points on the , the risk of shorting the unit should be considered. A minimum P CRMX™ PCB
ILOTINO
of 10mm of clearance space is recommended. Never install the within an enclosed space in which the P CRMX™ PCBILOTINO
Pilotino CRMX does not have sufficient space away from other components.
Connections
The comes equipped with wire to board quick connectors, and a socket connector to connect to the P CRMX™ PCB
ILOTINO
P ™ PCB P CRMX™ PCB P ™ PCB
ILOTINO ILOTINO ILOTINO
. Properly connect the to the with the boards facing the same direction.
All wire connections should fit securely into the connectors. Be sure to insert each wire into the connectors deep enough so that
no bare wire is exposed. A good rule of thumb is to strip the wires so that only about 3mm of insulation is removed.
To have the best connection, place the in a location where the antenna has a clear line of sight from the P CRMX™ PCB
ILOTINO
device connected to.
7
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
6.1 Rx Mode Installation
6.1.1 Basic Connections
Make sure the P CRMX™ PCB and antenna are connected to the P ™ PCB
ILOTINO ILOTINO
Power on the P ™ PCB board once proper wiring connections are done to eliminate short circuiting the board.
ILOTINO
Connect any DMX/RDM Controller to a DMX/RDM transmitter (see transmitter manual for connection)
On the transmitter, press the “Link Button” until the indicator LED on the P CRMX™ PCB changes
ILOTINO
color. (Mode color indicator LED is addressed on chapter 10)
8
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
6.1 Rx Mode Installation (cont.)
6.1.2 Daisy Chain
Make sure the P CRMX™ PCB and antenna are connected to the P ™ PCB
ILOTINO ILOTINO
Connect the DMX IN/OUT wires to each of the P ™ PCB boards in a sequence, similar to a daisy flower ring,
ILOTINO
to each corresponding connector.
Power on the P ™ PCB board once proper wiring connections are done to eliminate short circuiting the board.
ILOTINO
Connect any DMX/RDM Controller to a DMX/RDM transmitter (see transmitter manual for connection)
On the transmitter, press the “Link Button” until the indicator LED on the P CRMX™ PCB changes
ILOTINO
color. (Mode color indicator LED is addressed on chapter 10)
9
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
6.2 Tx Mode Installation
6.2.1 Basic Connections
Make sure each P CRMX™ PCB and antennas are connected to a corresponding P ™ PCB.
ILOTINO ILOTINO
Connect any DMX/RDM Controller to one of the P ™ PCB.
ILOTINO
Power on the P ™ PCB board once proper wiring connections are done to each to eliminate short circuiting
ILOTINO
the board.
For the P ™ PCB with the connected controller, using the bluetooth App (CRMX Toolbox) or the pairing button,
ILOTINO
change the P CRMX™ PCB mode from receiver to transmitter, Rx to Tx respectively.
ILOTINO
One P CRMX™ PCB will act as a transmitter and the other will act as a receiver. (Mode color indicator LED is
ILOTINO
addressed on chapter 10)
10
3307 West Street Rosenberg, TX 77471 USA - (281) 324-0908
Copyright © 2006-2021 SIRS Electronics Inc. All Rights Reserved P CRMX™ PCB
ILOTINO Instruction Manual
Updated 12/2021. Rev 2.4
Tabla de contenidos
Otros manuales de Convertidor de medios de SIRS-E
