Sinclair KJRP-75A Manual de funcionamiento
KJRP-75A
USER AND INSTALLATION MANUAL
IJ&%+)&##)
AIR CONDITIONING
This manual gives detailed description of the precautions
that should be brought to your attention during operation.
In order to ensure correct service of the wired controller
please read this manual carefully before using the unit.
For convenience of future reference, keep this manual after
reading it.
CONTENTS
1
Operation precautions
Operation conditions
Main functions
User interface
Instructions for use
Further details
1.2
1.1 01
02
1.3 02
OPERATION
2
06
07
08
Safety precautions
Installation accessories
Installation dimensions
2.2
2.1
2.3
INSTALLATION
1.4
1.5
1.6
03
04
05
09
16
Installation method
Schematic drawing of installation
2.5
2.4
01
1 OPERATION
WARNING
Means improper handling may lead to personal death
or severe injury.
CAUTION
Means improper handling may lead to personal injury
or property loss.
Read the safety precautions carefully before installing, and
must be obeyed.
This manual uses the following icons:
Prohibit Follow the guide lines
Please entrust the distributor or professionals to install the unit.
Before cleaning or maintenance, please cut off the power, and
prohibit to use water for washing, to prevent electrical shock.
1.1 Operation precautions
Do not operate by wet hand, to prevent electrical shock.
Do not use pesticide, disinfectant and flammability spray
materials to spray directly, otherwise will cause fire or
deformation.
Do not peel off the button and the cover by hand, to prevent
electrical shock.
1.2 Operation conditions
Voltage input
Ambient temperature range
(Stable operating environment)
Ambient humidity range
DC 5V
-10~43°C
≤ RH90%
02
1.3 Main functions
1. Connected to IDU main control board via 5-core shielded
cable;
2. Setting IDU operating status by tapping touch keys;
3. LED display.
03
1.4 User interface
On/Off Button
Mode Button
Backlight Button
Fan Speed
Button
Temp. Setting
Button
Cooling Heating Auto
Automatic Fan Speed
Dry
Display Area Of the
Wired Controller
Remote Signal
Receiving Area
Temperature
Fan Speed
Running Indicator
04
1.5 Instructions for use
1.5.1 Basic setting
2345
1
Tap Mode button
The operating mode changes in the
following order:
Cooling Heating AutoDry
1
Tap Fan Speed button
Seven fan speeds and Auto available.
3
Adjust temperature
Temperature range 17°C~30°C
2
Tap On/Off button
To start the unit and send all the configured
parameters.
4
Tap Backlight button
Backlight is on by default. Tap Backlight button
to turn it off.
5
Fan Speed button :
Fan speed cannot be set in Dry/Auto mode (Auto displayed).
Backlight mode:
1）Steady On: means backlight is normally on.
Tapping to start the unit can enter the backlight steady
on mode.
If backlight is off, tapping can switch to steady on mode.
2）Auto Off: means backlight is automatically off after 4s.
If backlight is off, tapping any button (except backlight and
On/Off) can switch to Auto Off mode.
1.6 Further details
1.6.1 Supplementary instructions
Applies to specific models only.
1.6.2 Remote control receiving function
Do not peel off the buttons and liquid crystal cover, to
prevent electric shock!
CAUTION
05
2 INSTALLATION
WARNING
Please entrust the distributor or professionals to
install the unit, do not install the unit by the user.
Do not uninstall the unit randomly.
The wiring should adapt to the wired controller
current.
The specified cables shall be applied in the wiring.
No external force may be applied to the terminal.
The circuit of wire controller is low voltage circuit,
do not contact to the high voltage circuit, and can
not be arranged in the same wiring pipe with the
high circuit, the distance between the wiring
pipes
should at least more than 300~500mm.
Read the safety precautions carefully before installing the
unit.
Stated below are important safety issues that must be
obeyed.
2.1 Safety precautions
06
07
Do not connect transition or extended connection
in the middle of the wirings of the wire controller.
Please confirm that all the following parts have been
supplied.
2.2 Installation accessory
Remarks
Wire controller
NameNo.
1
Qty
M4×20 Philips head screw
2Used to install the wired controller onto
the wall.
Used to control the IDU main unit.
Used to guide the operation and
installation of wired controller.
Installation and operation
manual
3
Plastic bolt
Connection cable set
4
5
1
2
1
1
2Used to install the wired controller onto
the wall.
Used to connect the IDU main control
board and the wired controller.
Tabla de contenidos
Otros manuales de Controladores de Sinclair
Sinclair
Sinclair KJR-29B Manual de usuario
Sinclair
Sinclair SDV 6 SWC-61 Guía
Sinclair
Sinclair SCC-16 Instrucciones de funcionamiento
Sinclair
Sinclair SWC-05W Manual de usuario
Sinclair
Sinclair XK60 Manual de usuario
Sinclair
Sinclair XK117 Manual de usuario
Sinclair
Sinclair XK19 Manual de usuario
Sinclair
Sinclair XK64 Manual de usuario
Sinclair
Sinclair SDV KJR-12B Manual de usuario
Sinclair
Sinclair SWC-03 Manual de usuario
Sinclair
Sinclair KJR-18B Manual de funcionamiento
Sinclair
Sinclair KJR- 90D Manual de usuario
Sinclair
Sinclair SWC-04 Manual de usuario
Sinclair
Sinclair KJR-120G Manual de usuario
Sinclair
Sinclair NIM09 Manual de usuario
Sinclair
Sinclair SCC-36 Manual de usuario
Sinclair
Sinclair SWC-86E Instrucciones de funcionamiento
Sinclair
Sinclair ZJ4011A Manual de usuario
Sinclair
Sinclair SWC-02 Manual de usuario
Sinclair
Sinclair SWC-86A Manual de funcionamiento
