Simply Automated URD27 Manual de usuario

Getting Started

Controlled Receptacle Accessory

(Top Outlet Controlled Bottom Always On)

For Models URD27 and URD28

Model URD27 Model URD28

Simply Automated Pre-Configured SimplySmartTM Series

Utilizes SimplySmartTM technology to make installation a breeze.

No computer programming required!

Simple-n-easy, ready to use lighting control.

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

Simply Automated Pre-Configured SimplySmartTM Series

Utilizes SimplySmartTM technology to make installation a breeze.

No computer programming required! Simple-n-easy, ready to use lighting control.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic safety precautions should always be followed, including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

2. Installation should be performed by a qualified electrician.

3. Keep away from water. If product comes into contact with water or other liquid, disconnect immediately.

4. Never use products that have been dropped or damaged.

5. Do not use this product outdoors, unless protected by a weatherproof enclosure.

6. Do not use this product for other than its intended use.

7. Do not connect multiple appliances / loads that, when combined, exceed the maximum load rating of the product.

8. To avoid risk of fire, burns, personal injury and electric shock, install this product out of reach of small children.

9. Do not install in areas that can exceed 120°F (e.g., in an attic).

10. Do not cover the product with any material when in use.

11. This product uses polarized plugs and sockets (one blade is wider than the other) to reduce the risk of electric shock. These plugs and

sockets fit only one way. If they do not fit, consult a technician. Do not use with an extension cord unless plugs can be fully inserted.

Do not alter plugs.

12. SAVE THESE INSTRUCTIONS

Section 1: Very Important Pre-Installation Notes

•Simply Automated devices require both a neutral (white) and hot (black) connection.

•Your home should be no more than 2500 square feet and have only one breaker panel. A phase

coupler is required in some home installations; especially homes > 2500 square feet or homes with

more than 1 breaker panel. See Section 5 for more information.

•Not intended for use in multi-dwelling (condo, apartment) buildings with 3-phase power.

•Do not reset to factory default configuration, pre-configured settings will be lost.

•UPStart software and a computer interface module or Scheduler-Timer can be used with a PC for

customizing pre-configured units and checking performance.

Section 2: Installation of Controlled Receptacle

Locate an electrical load you would like to turn ON/OFF (e.g. such as an appliance, a low-voltage landscape

lighting transformer, lamp or fan/pump/motor) with the Controlled Receptacle Accessory. To install the

Controlled Receptacle please refer to the User Guide enclosed in the receptacle product box, or see

http://www.simply-automated.com/documents/452-0014-0101_RevG_URD_%20UserGuide_090512.pdf

Test the Controlled Receptacle using a 4-button scene controller. Button 3 of the Tabletop Controller with

4- or 8-buttons (and Deluxe Dimmer with 4-buttons) is programmed from the factory to turn on each device

(dimmers, receptacles and modules) at a 100% dim level. Button 4 is programmed from the factory to turn off

each device (dimmers, receptacles and modules).

•Button 3 turns on/off each controlled receptacle (top outlet): Press (tap) button 3 one time to turn on each

controlled receptacle, press (quickly tap) two times to turn off each controlled receptacle.

•Button 4 turns off each controlled receptacle (top outlet): Press (tap) button 4 one time to turn off each

controlled receptacle.

Helpful Hint: If tapping a button does not turn on a connected load, make sure the load is connected to the top

receptacle (not the bottom). Make sure the electrical load’s ON/OFF switch is turned ON. Tapping should be

done quickly ensuring contact is made from the button to the base sensor.

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

Test Controlled Receptacle and Load Manually. If a Scheduler-Timer or scene controller with 4- or 8-buttons

is not available then you can manually turn ON/OFF the top, controlled receptacle using the program switch (i.e.

the blue/green indicator light is the program switch button):

•Go to the location of the receptacle, press (quickly tap) the program switch 9 times. The indicator will

continuously blink blue to confirm the controlled receptacle is in the manual control mode.

•While the indicator is flashing blue, press the program button once to toggle ON and a second time to

toggle OFF. Repeat as desired to ensure the load is connected and functioning properly. The connected

electrical load should turn ON and OFF as the program button is toggled.

•When done testing the receptacle and electrical load, press the program button two times quickly. The

indicator will stop flashing (or wait 5 minutes and the indicator will time out and stop flashing). The relay

module and load are now tested and ready to be controlled by the scheduler-timer, or other pre-configured

scene controllers.

•Repeat as necessary for additional controlled receptacles.

Helpful Hint: If the electrical load does not turn ON/OFF, make sure it is plugged into the top receptacle (not the

bottom). Make sure the electrical load’s ON/OFF switch is turned ON. Tapping should be done quickly

ensuring contact is made from the button to the base sensor.

Important Note: Each controlled receptacle has a unique ID number. You can find the ID number on the

front of the receptacle. The controlled receptacle accessories addressed in this guide will have ID #27

or ID #28. This is important information to note as it relates to operation with the Scheduler-Timer

accessory.

Section 3: Editing Buttons (Scenes) on Tabletop Controller (or Deluxe Dimmer) with 4-

or 8-Buttons

Each button on the Tabletop Controller with 4- or 8-Buttons (or Deluxe Dimmer with 4-buttons) controls a

SCENE that can easily be edited from the factory pre-sets. You can change the dimmers’ level or number of

receptacles controlled by each button to create your own custom scenes!

Section 3.a. Adding an Controlled Receptacle

Button 1. To add a controlled receptacle to button 1:

•Go to the Tabletop Controller (or Deluxe Dimmer), press button 1 to activate the scene. If any other

devices were previously set to be controlled by button 1, check to make sure they are ON.

•Go to the controlled receptacle to be added. Press (quickly tap) the program switch (i.e. blue/green

indicator button) 9 times. The indicator will continuously blink blue to confirm the controlled receptacle is in

the manual control mode.

•Press the program switch one time to toggle ON the controlled receptacle and the connected electrical load.

The load plugged into the top of the controlled receptacle should be ON.

•Press the program switch 2 times to turn off the flashing blue indicator (or wait 5 minutes for the indicator to

time out and turn off).

•Go to the controlled receptacle to be added, press (quickly tap) the program switch 5 times to place in the

program mode. The indicator will continuously blink green to confirm the controlled receptacle is in the

program mode.

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

•Go to the Tabletop Controller (or Deluxe Dimmer), press (quickly tap) button 1 seven times. You have

created a new scene!

Helpful Hint: If tapping button 1 does not turn ON the controlled receptacle, the electrical load's switch may be

in the OFF position. Go to the electrical load and turn ON using the load's ON/OFF switch, repeat the steps

outlined above. Tapping should be done quickly ensuring contact is made from the button to the base sensor.

Button 2. To add a controlled receptacle to button 2, follow the instructions outlined above in Section 3.a.

noting you will need to press (tap) button 2 seven times to program the new scene.

Helpful Hint: After tapping five times, controlled receptacle will stay in the program mode for approximately 5

minutes. You can always confirm if the controlled receptacle is in the program mode by checking for the

blinking green light of the program switch. If the indicator is not flashing green, to place in the program mode,

quickly tap the program switch five times. To exit the program mode, quickly tap the program switch two times.

Helpful Hint: The Tabletop Controller (or Deluxe Dimmer) can inadvertently be placed in the program mode by

tapping a button five times. The indicator above button 1 will continuously blink green for five minutes. To exit

the programming mode, quickly tap the button two times.

Section 3.b. Deleting a Controlled Receptacle

If you would like to edit a scene and delete a controlled receptacle from any button:

•Go to controlled receptacle you would like to delete, press (quickly tap) the program switch 5 times to place

in the program mode. The indicator will continuously blink green to confirm the controlled receptacle is in

the program mode.

•Go to the Tabletop Controller (or Deluxe Dimmer), press (quickly tap) the button you would like to delete the

controlled receptacle from eight times.

Helpful Hint: If you press (tap) a button and the controlled receptacle you deleted still turns on, repeat the two

steps outlined above. Tapping should be done quickly ensuring contact is made from the button to the base

sensor.

Helpful Hint: You may add or delete as many devices as you like at one time by putting them in the program

mode at the same time. Note when adding devices to a scene or changing dim level in a scene make sure the

scene is activated first (i.e. press the button 1 time), before changing dimmer levels or adding a device.

Section 3.c. Editing Buttons 3 or 4

Buttons 3 or 4. Button 3 is programmed to turn on all controlled receptacle. Button 4 is programmed to turn

off all controlled receptacle. We recommend not editing these buttons since all devices (up to ten dimmers,

receptacles and modules) in the Pre-Configured SimplySmartTM Series have similar settings -- one tap of button

3 turns all the devices on, one tap of button 4 turns all devices off. This pre-programming is a very powerful and

convenient feature using both the Tabletop Controller with 4- or 8-buttons and Deluxe Dimmer with 4-buttons.

Examples include entering a home (button 3 for ALL ON), leaving a home (button 4 for ALL OFF), bedside for

security and nighttime convenience (button 3 for ALL ON or button 4 for ALL OFF).

Important Note: Buttons 1 and 2 operate independently for the Tabletop Scene Controller Accessories

(models USQT22, US2TP11 and US28OTP23) and the Tabletop Controller included with the Lamp Starter

Kit (model DKIT-02) allowing one touch button control of more than 14 unique custom scenes. Create

one scene for button 1 of the Tabletop Controller Accessory (model USQT22) and a second scene for

button 1 of the Tabletop Controller from the Lamp Starter Kit (model DKIT-02). Create a third scene for

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

button 2 of the Tabletop Controller Accessory (model USQT22) and a fourth scene for button 2 of the

Tabletop Controller from the Lamp Starter Kit (model DKIT-02). And, the 8-button Tabletop Controller

(model US28OTP23) has 6 independent buttons available for custom scene control.

Editing Buttons 3 and 4. Button 3 is programmed from the factory to turn ON all controlled receptacle,

dimmers, modules and accessories. Button 4 is programmed from the factory to turn OFF all devices. To edit

these buttons for controlled receptacles follow the procedures in Section 3.a and 3.b.

To make button 3 available for an independent scene and edit button 4 so that it turns all devices ON/OFF

(instead of just off):

•Go to the Tabletop Controller (or Deluxe Dimmer), press button 3 to activate the ‘All ON’ scene. Any

modules or dimmers configured for this scene button should be ON.

oIf any dimmers are not ON, press the top rocker to turn ON the dimmer.

oIf any lamp module’s load is not ON, turn the lamp’s ON/OFF switch ON.

oIf any appliance module’s load is not ON, turn the load’s ON/OFF switch ON. And, if necessary,

turn ON the appliance module by pressing and holding the program switch until the indicator

flashes red, then press (quickly tap) the program switch to toggle the appliance module ON. Press

(quickly tap) the program switch two times to turn off the flashing red indicator.

oIf any controlled receptacle’s load is not ON, turn the load’s ON/OFF switch ON. And, if necessary,

turn ON the controlled receptacle by pressing (quickly tapping) the program switch 9 times. The

indicator will continuously flash blue, and then press the program switch to toggle the controlled

receptacle ON. Press (quickly tap) the program switch two times to turn off the flashing blue

indicator.

•Go to the Tabletop Controller (or Deluxe Dimmer), press (quickly tap) button 4 seven times to store the ‘All

ON’ levels. The controlled receptacle, modules and dimmers will turn off and back on indicating the level

was stored.

•To test, press (quickly tap) button 4 two times to turn off all controlled receptacles, modules and dimmers,

then press button 4 one time to turn on all devices. Congratulations you have created a new scene! Button

3 is now available to edit for another scene and you can still turn all devices on/off with button 4.

Helpful Hint: The Tabletop Controller can inadvertently be placed in the program mode by tapping button 1 five

times. The indicator above button 1 will continuously blink green for five minutes. To exit the programming

mode, quickly tap the lamp module’s program switch two times.

Section 4: Simple-n-Easy Expansion for SimplySmartTM Series. Fully Compatible.

All Starter Kits and Accessories -- Dimmers, Tabletop Controllers, Controlled

Receptacles, Lamp, Appliance and Fixture Modules, plus Scheduler-Timer.

Simply Automated Pre-Configured SimplySmartTM Series offers simple-n-easy expansion capability. Begin with

the Dimmer or Lamp Starter Kit, add other starter kits, additional standard dimmers, additional Deluxe Dimmers

with 4-buttons, additional modules, Tabletop Controllers with 4 or 8-buttons or any of the other pre-configured

kits or accessories. All the pre-configured kits and accessories can be edited and added to scenes as

previously described – only limitation being not more than one of each model number or kit number per

installation. One touch button convenience to turn ON/OFF up to ten or more Simply Automated devices –

custom scenes you create!

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

Dimmer Starter Kit Lamp Starter Kit Landscape Relay

Includes 2 dimmers and deluxe Starter Kit Includes 2 lamp Starter Kit Includes 2 relay

dimmer with 4-button modules and tabletop controller modules and scheduler-timer

scene control (model: DKIT-01) with 4-buttons (model: DKIT-02) (model: DKIT-05)

Landscape Dimmer Lamp (Dimmer) Modules Dimmers

Starter Kit Includes 2 standard

dimmers and scheduler-timer

(model: DKIT-06)

UML7 UML8 US1W9 US1W10

Tabletop Controllers Controlled Receptacles Deluxe Dimmer

(with 4-button, 4-button with LEDs (top outlet controlled, bottom (with 4-button scene

or 8–button scene control) outlet always on) control)

US2TP11 USQT22 US2O8TP23 URD27 URD28 US2W12 US2W24

Important Note: only one of each pre-configured accessory model number can be ordered per home

installation.

Add a Scheduler-Timer (model: UCS-01) to automatically turn ON/OFF indoor or outdoor security lighting. Or to

create night time convenience pathway lighting. Energy savings dimming feature (from 10%, 20%, 30%, 40%,

to 90% dimming levels). Random 'vacation mode' setting gives a home the lived in look. Built-in celestial clock

computes sunrise and sunset. Calculates daylight savings time.

Getting Started

Controlled Receptacle Accessory

For Models URD27 and URD28

Simply Automated, Incorporated

6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA

Technical Support: www.simply-automated.com or 800-630-9234

452-0014-0025 Rev. A Revised: September 23, 2011

The Scheduler-Timer is easily and quickly programmed -- no PC connection is necessary. Just

set the time, your location (using your zip code), the Network ID # (250), and you’re ready to

input on/off events using the ID # for each dimmer (each dimmer has a unique ID number). You

can find the ID number on the front of each dimmer or the back of each module. For the

Accessories (E.g. UML7, UMA25, US1W9, US2W12, etc...), the number digits at the end of the

model number indicate the device ID#. For example the accessories listed above have device

ID#s 7, 25, 9, and 12, respectively.

Section 5: In Case of a Problem

Phone: 760-431-2100 Ext. 138 Monday-Friday 8AM-5PM (Pacific Time) for assistance, or write

[email protected].

Phase Coupler: Your home should be no more than 2500 square feet and have only one breaker panel. A

phase coupler is required in some home installations; especially homes > 2500 square feet or homes with more

than 1 breaker panel. If you have tested the buttons for each lamp module, but one or more of the lamp

modules do not turn on, the circuits in your home may need phase coupling or phase alignment. All homes

have a 240V feed to the main breaker panel box, where the 240V is separated into 120V in two phases, an A

and B. You will need to install a phase coupler, or use dimmers and modules on one phase (align or move

lighting circuits, at the breaker, that have these dimmers and modules to either phase A or B, not both) see

http://simply-automated.com/products/cats/phase_couplers.php for options.

Model # Description

ZPCI-P30A Plug-In Inverting Phase Coupler, fits a standard (NEMA 10-30) 240VAC / 30 Amp

clothes dryer type outlet

ZPCI-P50A Plug-In Inverting Phase Coupler, fits a standard (NEMA 10-50) 240VAC / 50Amp

clothes dryer type outlet

ZPCI-W Wire-in Inverting Phase Coupler

ZPCI-B Breaker Panel Inverting Phase Coupler

Network ID #: The default Network ID #setting for the Pre-Configured Series is 250. This information is

needed when using the Scheduler-Timer.

Section 6: Simply Automated Custom Expansion Series

Powerful Custom Expansion Capability – up to 250 devices – using your PC and UPStart software! Devices

include single rocker dimmers, deluxe dimmers with different faceplates (up to 8 buttons), lamp or appliance

modules, tabletop pedestal with 8 buttons, wall receptacle, fixture relay, fixture dimmer or scheduler-timer.

Control lighting and 120VAC appliances, heaters, fans, motors or pumps. Programmable dimming rates (1

second, 5 second, up to 4 hours). Energy saving countdown timer function. Lighting control for your entire

home! Visit http://www.simply-automated.com/products/products.php

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Automatización del hogar de Simply Automated

Simply Automated

Simply Automated SimplySmart Series Manual de usuario

Simply Automated

Simply Automated SimplySmart Series Manual de usuario

Simply Automated

Simply Automated DKIT-02 Manual de usuario

Simply Automated

Simply Automated SimplySmart Series Manual de usuario

Manuales populares de Automatización del hogar de otras marcas

Truth Hardware

Truth Hardware Sentry II Manual de usuario

FIBARO

FIBARO FGWPA-111 Manual de usuario

Hezborg

Hezborg BGR8016B Manual de usuario

MYDLINK

MYDLINK Pro Series Manual de usuario

Panasonic

Panasonic KX-HNA101FX Manual de usuario

GamaBit

GamaBit Houseper Manual de usuario

nedis

nedis WIFILRF10C37 Manual de usuario

Veho

Veho TA45 Manual de usuario

Nexa

Nexa ZPR-111 Manual de usuario

Vimar

Vimar 00801 Manual de usuario

Leviton

Leviton 47604-F6 Manual de usuario

EVERSPRING

EVERSPRING AN180 Manual de usuario

Coltech

Coltech 18-1339 Manual de usuario

IDS

IDS NXT vegas Guía

Vimar

Vimar 03975 Manual de usuario

iNels

iNels RFIM-20B Manual de usuario

EVA Logik

EVA Logik ZW30 Manual de usuario

Leviton

Leviton ODCØP-S0W Manual de usuario