Simmons SD1500 Manual de usuario

Otros manuales para SD1500

1

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Tambor de Simmons

Simmons

Simmons SD2000 Manual de usuario

Simmons

Simmons SDS 9 Manual de usuario

Simmons

Simmons SD1500 Manual de usuario

Simmons

Simmons SDXpress2 Manual de usuario

Simmons

Simmons SD7K Manual de usuario

Simmons

Simmons SD550 Manual de usuario

Simmons

Simmons SDMK4 Manual de usuario

Simmons

Simmons TITAN 20 Manual de usuario

Simmons

Simmons SD XPRESS Manual de usuario

Simmons

Simmons SDS 1 Manual de usuario

Simmons

Simmons TITAN 50 Manual de usuario

Simmons

Simmons SDS 9 Manual de usuario

Simmons

Simmons SDMP1 Manual de usuario

Simmons

Simmons SD5Xpress Manual de usuario

Simmons

Simmons SD300KIT Manual de usuario

Simmons

Simmons SD9K Manual de usuario

Simmons

Simmons SD5K Manual de usuario

Simmons

Simmons Five Manual de usuario

Simmons

Simmons SD 100 Manual de usuario

Simmons

Simmons SDHB2 Manual de usuario

Simmons

Simmons SD5X Manual de usuario

Simmons

Simmons SDS 8 Manual de usuario

Simmons

Simmons SD1 Manual de usuario

Simmons

Simmons sd1000 kit Manual de usuario

Manuales populares de Tambor de otras marcas

Yamaha

Yamaha RX-21 Manual de usuario

Roland

Roland TD-9K Manual de usuario

Sudoku

Sudoku LEXUS Manual de usuario

Roland

Roland CR-80 Manual de usuario

V-Drums

V-Drums V-Tour TD-9KX2 Manual de usuario

Yamaha

Yamaha DTXPLORER Manual de usuario

Cherub

Cherub WRW-206 Manual de usuario

Opti-Med

Opti-Med JM-D1 Series Manual de usuario

Roland

Roland CR-80 Manual de usuario

Yamaha

Yamaha DTS70 Manual de usuario

Yamaha

Yamaha DTXPRESS Manual de usuario

Roland

Roland RM-2 Manual de usuario

ATV

ATV aD5 Manual de usuario

Alesis

Alesis DM Pro Kit Manual de usuario

Roland

Roland TR-808 Manual de usuario

Roland

Roland SPD-20 Manual de operación y mantenimiento

Koma Elektronik

Koma Elektronik RH 301 Manual de usuario

Roland

Roland TR-8 Manual de usuario

CAUTION!

While Simmons makes every effort to provide the highest quality products, metal shavings and/or burrs occasionally remain as a by-product

of the manufacturing process. To avoid injury, please use caution when adjusting clamps, or when working with pipe and screw ends.

Drum Rack Components

ASSEMBLY INSTRUCTIONS

The first name in electronic drums.

Before assembly, please check that all the items listed below are present.

Inside this package

rack assembly

1. Remove all preassembled tubing with clamps

from packaging.

2. Each T-Fitting and tube end-ﬁtting is labeled with

a number. Lay the vertical and horizontal tubes

on the ﬂoor with the numbers matching.

L–Rods for Pads x5

Please note the numbers stamped on each

tube-end and tube-ﬁtting

1

2

7

34

56

Left Left Center Right Center Right

Snare Drum

Pad Tube

Sound Module/Hi-Hat Tube

Tom Pad

Tube, Center

Tom Pad

Tube, Right

2

SD1500 ELECTRONIC DRUM KIT ASSEMBLY SHEET

8. If further adjustments of height and angle are required, loosen

the appropriate T-ﬁttings with the 4 Drum Key Fasteners and

rotate, raise, or lower into desired positions. Retighten Drum

Key Fasteners making sure the gaps between the ﬁttings are

close to even.

3. There is a Drum Key Fastener location on the end of each

ﬁtting. Back this fastener out until the pointed end is no longer

protruding inside, but do not remove it. Do this for all the

ﬁttings that have this feature on the vertical leg-ﬁttings .

7. Loosen the Drum Key Fastener on ﬁtting as above. Insert

Snare Drum into ﬁtting and tighten. Loosen T-ﬁtting with

the 4 Drum Key Fasteners and rotate into desired position.

Retighten Drum Key Fasteners making sure the gaps between

the ﬁttings are close to even.

6. After you have the rack assembled, double check the

Drum Key Fastener and make sure they are all snug (do

not over tighten).

rack assembly CONTINUED

Match Numbers

9. Loosen L-rod wing knobs on tom clamps.

Insert black plastic end of L-rod into tom

clamps and tighten wing nuts.

4. Begin with T-ﬁtting/tube end number and insert into the

corresponding left vertical leg. The surfaces of the ﬁtting

should almost touch. Tighten the Drum Key Fastener until

snug (do not over tighten).

1

5. Continue assembling the rack working your way around to

T-ﬁtting/tube end number (to the vertical right leg).

6

7

7

Completed Assembly