Simfer S 3100 WT Manual de usuario
Dear Customer,
Thank you for preferring Simfer products. We aim to ensure that you can obtain
utmost efficiency from this product made in accordance with the sense of total quality in a
meticulous working environment at our modern facilities without causing any harm to the
nature.
We recommend you to carefully read the User Manual before using the Simfer quartz
heater and to keep it permanently so that it can maintain its original features for a long time
and serve you as efficiently as possible.
NOTE:
This User Manual has been prepared for several models. Some features specified in
the manual may not be available in your device. These features are market with “*”.
The devices are for domestic use. There are not intended for commercial use.
”PLEASE READ THE INSTRUCTIONS BEFORE ASSEMBLING OR USING
THE DEVICE”
This product has been produced in modern, environmentally friendly facilities without
causing any harm to the nature.
“It complies with the EEE Directive”
1
CONTENTS:
Dear Customer ……………………………………………………………………………... 1
Contents …………………………………………………………………………………….. 2
Safety Instructions ……………………………………………………………………..… 3, 6
Technical Features
Device Equipment …………………………………………………………………… 7
Device Equipment, Foot Assembly .…………………………………………………. 8
Usage of the Humidifier Section, Control Panel ………………..…………………… 9
Control Panel, Usage of the Humidifier ..…………………………………………… 10
Technical Table, Usage of the Heater ………………………………………..………11
Maintenance and Cleaning ……………………………………………….………………. 12
Troubleshooting …………………………………………………………..……………….. 13
Certificate of Warranty ………………………………………………………………….... 14
2
SAFETY INSTRUCTIONS
This device has been produced in accordance with safety regulations. Operation in violation
of the rules may cause harm to people and the device.
Read the user manual carefully before operating the device. You can find important
information about assembly, safety, operation and maintenance in the user manual. This way
you can both protect yourself and prevent the device from getting damaged.
If the Supply Cord is damaged, it must be replaced by the manufacturer or its service agency
or equally qualified personnel in order to prevent a dangerous situation. The heating tube
available on the device must be checked for cracks and deformation. If the glass tubes are
damaged, the heater must not be used and the authorized service must be contacted.
It must be checked whether the main power line is 220-240V AC, 50-60 Hz and connected to
the circuit breaker. Network safety must be checked. The circuit breaker must be 16 amperes.
The device must be certainly used with grounded receptacle and the grounded receptacle must
be away from the heater area and hot surface. Furthermore, looseness and damage check must
be performed on the receptacle. Loose receptacles cause harm to the device and installation.
The device must not be connected to the same electric cable or circuit breaker as other devices.
The power cable must not be left on or near the hot body of the device.
If the device is not to be used for a long time, moved to another place, cleaned or calibrated,
the plug of the device must be disconnected. It must be made sure that the device has cooled
down.
Do not use the device in places very close to any bathroom, shower or swimming pool.
3
SAFETY INSTRUCTIONS
This device is not intended for use by physically, emotionally, and mentally disabled people
(including children) or people with insufficient experience and knowledge unless a person
responsible for safety of the device provides supervision and direction regarding the operation
of the device.
Do not let the device touch water under any circumstances.
The electric connection of the device must be disconnected from the network during assembly
and maintenance or repair works. The device must be unplugged in order to disconnect it
from the network.
Make sure the supply cable and receptacle are clean and dust free before operation.
Do not pull by the cable while unplugging the supply cable.
Make sure to hold properly while plugging or unplugging the device. Do not touch the supply
cord with wet hands.
Do not make any additions to the supply cord. Otherwise it may result in malfunction, electric
shock or fire.
Do not pass the supply cable under heavy objects. Otherwise it may cause electric shock or
fire hazard.
Do not shut down the heater only by unplugging it and deactivating the circuit breaker;
always use the heating element function button.
As covering or misplacement of the heater causes fire hazard, this heater may not be used
together with any automatic programmer, timer or any other mechanism.
The fireguard of this heater aims to prevent direct access to heating elements and it must be in
place while the heater is in operation.
4
SAFETY INSTRUCTIONS
Do not use the device for any other purpose other than the intended use. (Do not use it for
drying clothes or keeping animals or plants warm)
Do not attempt to clean the device using solvents or flammable liquids. (This may cause
electric shock or fire)
Do not use the device while sleeping or when you are away from the device.
Avoid using extension cables as this may cause fire due to overheating. If you have to use an
extension cable, the cable section must be at least 2 mm2(14 AWG).
The device must be used on a flat and smooth ground.
Do not use the device in unstable or insecure places.
Do not attempt to demount or repair the heater. Do not shake the heater under any
circumstances.
A little smoke and smell may be released during the first use. This is normal. Do not touch the
device while it is in operation or immediately after shutting it down.
The device must be unplugged before cleaning. Do not clean the device with steam cleaners.
Children must be watched to ensure that they do not temper with the device. The fireguard
does not provide complete protection for little children and disabled people.
Keep the device in dry and enclosed spaces.
The devices must be used only with the resistances in horizontal position (on the feet).
5
SAFETY INSTRUCTIONS
The distance between the device and ceiling must be minimum 0.75 meters.
There must be minimum 1 meter distance between the device and curtains, wood, cartons,
fabrics and other materials, living organisms and other devices.
No finger or any other object must be put through the protective screen.
The device must not be placed right under any receptacle.
Do not move the device while it is in operation. The resistances may be sensitive and
malfunction when they are hot. Always shut down the device and wait for it to cool down
before touching it.
Do not cover the device in order to prevent overheating. Do not block the ventilation ducts
and the wire area.
Do not operate the device as close as 7.60 meters to inflammable materials (petrol, alcohol
etc.) or place motor vehicles not expected to operate near it. Do not put flammable materials
such as solvents, thinner etc. on or near working surfaces of heating devices or do not place
electrical home appliances near them.
6
TECHNICAL FEATURES
Device Equipment (Slim)
7
Vapor discharge and water
filling point Louvers
Holder
Thermostat
Heating function
Fan and Vapor function
Heating glass tube
Protective screen
Plastic foot
Device Equipment (Tower)
Vapor discharge and water
filling point
Louvers
Heating glass tube
Plastic Holder
Thermostat
Heating function
Fan and Vapor function
Protective screen
Plastic foot
TECHNICAL FEATURES
Device Equipment (Slim, Tower)
The foot assembly must be as indicated in the picture above. Apply pressure with your hand
from the foot to the body after making sure that the protrusion on the foot corresponds to the
duct. A click sound will be heard when the nails fit in their places.
After making sure that the foot is in position, it must be secured with the screw available in
the box as shown in the figure above.
8
Vapor discharge and water filling
point
Plastic holder
Vapor discharge and water filling
point
Plastic holder
Lighted water level
indicator Lighted water level
indicator
Foot assembly
TECHNICAL FEATURES
Control Panel (Slim)
Off
1s
t
level resistances (in the 1s
t
row)
2nd level resistances (in the 1s
t
and 4th rows)
3rd level resistances (in the 1s
t
, 2nd, and 3rd rows)
4th level resistances (all)
Thermostat
Turbo Fan
Humidifier
Control Panel (Tower)
Off
1s
t
level resistances (in the 1s
t
row)
2nd level resistances (in the 1s
t
and 3rd rows)
3rd level resistances (in the 1s
t
, 2nd, and 4th, 5th rows)
4th level resistances (all)
Turbo Fan
Humidifier
9
TECHNICAL FEATURES
Usage of the Humidifier Section (*) Option
1. Open the cover as indicated in the figure.
2. Check the water level and add enough water to the device from the opening. The water
capacity is about 330 ml.
3. Attention! As adding too much water will cause overflow, it may damage the electric
parts of the device and cause electric shock.
Usage of the Humidifier
1. Use the water filling point shown in the picture to fill water.
2. Check the water level and add enough water to the device from the opening. The water
capacity is about 150 ml.
3. Attention! As adding too much water will cause overflow, it may damage the electric
parts of the device and cause electric shock.
4. Watch the water indicator while adding water to the device. The water level must not
exceed the point indicated by the water indicator. Water must be added to the device
when the water amount is reduced to ¼. Water reduced to ¼ will not evaporate.
Operating the device without water and in steam mode may damage the device.
10
Slide in the arrow
direction Slide in the arrow
direction
Water filling
point Water filling
point
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Calentador de Simfer
Manuales populares de Calentador de otras marcas
Empire Heating Systems
Empire Heating Systems WCC65 Manual de usuario
Wetekom
Wetekom 92 86 43 Manual de usuario
Desa
Desa SPC170-F Manual de usuario
Watlow
Watlow Watrod Electric Tubular Heaters Manual de usuario
Haverland
Haverland ECO-DRY GPS Series Manual de lista de piezas
Stelpro
Stelpro ASILVC2060 Series Manual de usuario