SIMARINE SDI01 Manual de usuario

S I M A R I N E ®

SDI01 Inclinometer

USERS MANUAL

V1.0

USER MANUAL- V 1.0 DE

SDI01 Inclinometer

1. Introduction .......................................................................... 3

2. Safety .................................................................................... 3

3. Overview .............................................................................. 4

4. Instalation ............................................................................. 4

4.1 Cables ................................................................................................................. 4

5. Connecting a Digital Inclinometer Module to a

SIMARINE system ................................................................. 5

5.1 Directly to the splitter ....................................................................................... 5

5.2 Through another module to the splitter ......................................................... 6

6. After connecting the module ................................................ 6

7. Calibration of the module ..................................................... 7

7.1 Calibration using the CAL button on the SDI01 module ................................. 7

7.2 Calibration through the monitor ...................................................................... 8

8. Configuring SDI01 inclinometer module ............................... 9

8.1 Name .................................................................................................................. 9

8.2 Nonlinear ........................................................................................................... 9

8.3 Display ................................................................................................................ 9

8.4 Reverse ............................................................................................................... 9

9. Technical specifications ...................................................... 10

10. Troubleshooting ................................................................. 10

10.1 Inclinometer not showing up on screen ........................................................ 10

SDI01 Inclinometer

1. Introduction

SDI01 is a high-resolution digital inclinometer for pitch and roll with manual

calibration. It is fully compatible with existing SIMARINE monitoring systems. The

module was designed so that configuration and calibration of the inclinometer is

quick and user friendly.

The SDI01 digital inclinometer has the following connections:

1 CURRENT INPUT UP TO 300A

2 VOLTAGE INPUTS

1 TEMPERATURE INPUT

NOTE: Please make sure you are running a firmware version higher than version

3.000.

2. Safety

Only qualified electricians with proper safety equipment should make installation

of Simarine electronics. When working with batteries, you should wear protective

clothing and eye protection.

CAUTION: Batteries contain acid, a corrosive, colorless liquid that can burn your

eyes, skin, and clothing. If the acid comes into contact with eyes or skin, wash out

with lukewarm water and immediately seek medical support.

CAUTION: Do NOT connect anything to a damaged battery. It could heat up,

catch fire, or explode.

CAUTION: Lead-acid batteries can generate explosive gases during operation.

Never smoke, allow flames, or sparks near the battery. Make sure to keep

sufficient ventilation around the battery.

SDI01 Inclinometer

3. Overview

A - Calibration button

B - 2x SICOM port

4. Instalation

CAUTION: Install the shunt module in a clean and dry place protected from

accidental spilling of liquids.

Place the inclinometer on a firm and stable surface.

4.1 Cables

For the SiCOM connection, use the supplied cable. If not possible, use the

following table to determinate the correct cable type.

CABLES

Cable length

Cable type

< 5m

No limitations

>= 5m

2x2x0.25 mm2 twisted pair (recommended)

SDI01 Inclinometer

5. Connecting a Digital Inclinometer Module to a

SIMARINE system

Like any other SIMARINE modules, the SDI01 also communicates with the

SIMARINE monitoring system through a SiCOM data cable, which is included with

the inclinometer.

You can either connect the module directly to the SPLITTER or you can

connect it to another module which is already connected to the SPLITTER and

thus forming a so called “daisy chain” (indirect wiring).

5.1 Directly to the splitter

Connecting a digital inclinometer directly to the splitter port.

STANDARD WIRING – DIRECTLY TO THE SPLITTER

SDI01 Inclinometer

5.2 Through another module to the splitter

Connecting the inclinometer to another module to the splitter.

INDIRECT WIRING – THROUGH ANOTHER MODULE TO THE SPLITTER

6. After connecting the module

After connecting the module, your monitor will automatically recognize it and

configure two new inclinometer devices, which you can see in the list of

inclinometers MENU > DEVICES > INCLINOMETERS

On the main screen, after scrolling down (using arrow-down button), past the

first screen, you will reach a new »Inclinometers« screen, which shows you the

current readings of your inclinometer module. Please note that at this step, due

to the lack of calibration, it is expected that the angle values are incorrect. The

process of calibrating your sensor is explained in the next section.

SDI01 Inclinometer

7. Calibration of the module

Before calibrating the module, you must make sure that the module is mounted in

its final position and the vehicle is parked on a level surface.

The calibration procedure can be executed in two ways. Either through the

monitor or by using a CAL button on the inclinometer module itself.

The result of the calibration is 0° angles for both PITCH and ROLL inclinometers

at the current position of the module.

7.1 Calibration using the CAL button on the SDI01

module

To calibrate the module using the CAL button, please press and hold the CAL

button which is located on the top right corner of the module. Hold the button

until the LED light on the module starts flashing red.

SDI01 Inclinometer

7.2 Calibration through the monitor

To calibrate the module through the monitor, please navigate to the

inclinometers screen. Press and hold both up-arrow and down-arrow buttons

at the same time until the confirmation screen appears.

After the conformation screen appears, long press the

button to confirm.

SDI01 Inclinometer

8. Configuring SDI01 inclinometer module

Although the module is designed so that is works more or less out of the box

(requiring only calibration), there is a variety of settings available for user to

configure.

8.1 Name

The display name of your inclinometer. You can select either PITCH or ROLL.

8.2 Nonlinear

This parameter is for display purposes. By configuring NONLINEAR setting to

OFF, the inclination line will follow the angle values read by the sensor more

closely. This means that at the lower angles (1°–10°) the drawn offset may not be

as apparent.

The default value is ON.

8.3 Display

The parameter determines if the inclinometer is to be displayed on the

inclinometers screen.

The default value is ON.

8.4 Reverse

Reverses the display, which means that at the 5° angle the angle will be

presented as –5°. This gives the user more options when first mounting the

module to its location.

SDI01 Inclinometer

9. Technical specifications

SDI01

Operating

Voltage range

6 – 35 V

Resolution

0,1°

Output format

SiCOM

Range (putch&roll)

+-89°

Power consumption

Power consumption at 12V

1mA

10. Troubleshooting

10.1 Inclinometer not showing up on screen

Make sure that the inclinometer module is connected to the SICOM input.

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de SIMARINE

SIMARINE

SIMARINE PICO Manual de instalación y operación

SIMARINE

SIMARINE SC303 Manual de usuario

SIMARINE

SIMARINE PICO Manual de usuario

SIMARINE

SIMARINE SC303 Manual de usuario

SIMARINE

SIMARINE PICO Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario