Sim-Lab DASH SD43 LED Manual de usuario
DASH SD43 LED
VERSION 1.0
Last updated: 16-03-2022
INSTRUCTION MANUAL
2|2 11
BEFORE YOU START:
Thank you for your purchase. In this manual we will provide you with the means to get started using your
new dash!
Dash SD43 LED
Features:
4.3” 480x272 Pixel color TFT LCD USBD 480
23 full RGB leds
Up to 60 FPS
16 bit Colors
USB Powered
Multiple software options
Drivers included
Mounting the dash is very easy thanks to the included mounting plate. With just 2 bolts (A5) you can
mount it directly to your Fanatec base. For mounting onto a servo motor mount you can use the existing
bolts with which the servo is mounted to a front mount or servo motor holder.
3|3 11
Mounting the dash
To be able to mount the dash on the hardware of your choice, we provide adapter
plates. Which one you have will depend on your purchase and may different from
the following one we show.
A6
A8
OSW/Simucube/VRS
Loosen the existing upper bolts which hold the motor in place. Simply slide the
adapter plate over the exposed thread and tighten the bolts against the plate.
Note: the adapter plate for a Simucube Ultimate is sold separately.
A4
4|4 11
Fanatec DD1/DD2/CSL
Locate the accesory mounting holes on your Fanatec hardware and use the two
bolts (A4) and washers (A6) from our supplied hardware kit.
A5
A7
Fanatec CSW
Although the regular Fanatec adapter plate can be fitted, we prefer this one because
it offsets the dash from the steering wheel.
Note: This plate is sold separately.
A5
A7
A3
5|5 11
Installing drivers
To make the display part of the dash functional, specific drivers are needed. Drivers
can be downloaded from the product page.
> download drivers <
Installation
To install the display drivers, run the downloaded package and follow these steps:
Press ‘Next’.
Specify the location where to install the drivers:
Press ‘Install’.
After the loading bar is full and says ‘Completed’:
Press ‘Close’. Installation of the display drivers is now done.
6|6 11
SimHub installation
To control the LEDs of the dash, Simhub can be used.
Download the lastest version of Simhub from https://simhubdash.com
Installation
Unzip the downloaded file and run the setup file:
Press ‘Next’.
Specify the location where to install the software:
Press ‘Next’.
Make sure all options are checked:
Press ‘Next’.
7|7 11
SimHub configuration
If you haven’t connected the dash with the supplied USB cable to your computer, this
is required from this point forward.
Activation
To use the display with SimHub, it needs to be enabled:
Press ‘Dash Studio’ (1).
Press ‘Install’.
After installation press ‘Finish’.
1
8|8 11
Press ‘USBD480’ (2).
In the ‘Screen #1’ section, check ‘Enable display’ (3). The ‘Connected’ indicator will
appear on its right hand side. When the screen is connected, go back to
‘Dashboards’ (4).
Hover over the dashboard you want to display and select ‘Start’.
A popup will appear, select ‘On USBD480 screen’ (6).
The display will now boot using the selected dash.
NOTE: Importing or changing dash profiles is not part of this document. For more
information on that topic, please see the SimHub documentation.
3
24
6
5
9|9 11
Controlling the LEDs
A sample LED profile can be downloaded from the product page.
> download led profile <
To enable or adjust LEDs, navigate back to the ‘USBD480’ page in ‘Dash Studio’. You
may also refer to Pages 5/6 of this document.
Check the ‘SIMLAB DASH 2.0’ module (1). A ‘Connected’ indicator will appear to
confirm the connection. Press ‘Profiles manager’ (2) to import the profile.
Click on the import profile icon (3).
Browse to the location where you stored the LED profile, select it and press ‘Open’.
The load the profile, make sure it is selected (SD43-LED) and press ‘Load’ (4).
1
2
3
4
10 |10 11
Changing the LEDs’ functions.
To change the LED effects you need to now the LED numbering of the dash. The
numbering starts at the bottom left and continues clockwise to the bottom right.
See the image below for reference:
There should be enough info in the sample profile to be able to adjust to your liking.
Just keep in mind, you mostly need two values. The number of the LED where you
want an effect to start, and the amount of LEDs to use for said effect (in a clockwise
direction).
For further assistance and more information on effects, please see the SimHub
documentation.
1
2
3
4
5
23
22
21
20
19
6 7 8 9 10 11 12 13 14 15 16 17 18
IN THE BOX
#Part QTY Note
A1 Dash SD43-LED 1
A2 USB B Cable 1
A3 Adapter plate Fanatec 1 Fits all Fanatec hardware.
A4 Adapter OSW/SC/VRS 1
A5 Bolt M6 X 12 DIN 912 2
A6 Bolt M5 X 10 DIN 7380 4 To fit adapter plate to dash.
A7 Washer M6 DIN 125-A 4
A8 Washer M5 DIN 125-A 4
Disclaimer: for some entries on this list, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
Bill of materials
Tabla de contenidos
Otros manuales de Rack y soporte de Sim-Lab
Sim-Lab
Sim-Lab GT1-EVO Manual de usuario
Sim-Lab
Sim-Lab X1-PRO Manual de usuario
Sim-Lab
Sim-Lab TR1/GT2 Manual de usuario
Sim-Lab
Sim-Lab FREESTANDING VARIO SINGLE Manual de usuario
Sim-Lab
Sim-Lab FRONT MOUNT EVO Manual de usuario
Sim-Lab
Sim-Lab GT1-PRO Manual de usuario
Sim-Lab
Sim-Lab SLA089 Manual de usuario
Sim-Lab
Sim-Lab VESA 75/100 Manual de usuario
Sim-Lab
Sim-Lab PODIUM BRACKET SET Manual de usuario
Sim-Lab
Sim-Lab GT1-EVO Manual de usuario
