SilverStone ST400 STRIDER Manual de usuario

ST400

STRIDER

Effortless power on demand

Dual +12V rails for newest systems

6 pin PCI express connector

Silent running 120mm fan

Four serial ATA connectors

Components designed for reliability

Support ATX 12V 2.2

SilverStone STRIDER ST400

ATX12V 2.2 Switching Power Supply

PS/2 400W

SPECIFICATION

1. GENERAL REQUIREMENTS

2. INPUT REQUIREMENTS

This specification describes a 400 watts power supply. With+ 5V stand-by , remote

ON/OFF control for ATX system and passive PFC(Power Factor Correction) (option)

circuit at 230 Vac.

The power supply shall operate in 115Vrms±10% or 230Vrms ±10%. The power

supply shall operate from an AC mains frequency of 47 through 63 Hz. Maximum

inrush current from power-on (with power on at any point on the AC sine) and

including, but not limited to, three line cycles, shall be limited to a level below the

surge rating of the input line cord, AC switch if present, bridge rectifier, fuse, and EMI

filter components. Repetitive ON/OFF cycling of the AC input voltage should not

damage the power supply or cause the input fuse to blow.

The AC mains steady-state RMS input current shall be:

8.5 amps maximum / 115 Vrms, 60 Hz.

5 amps maximum / 230 Vrms, 50 Hz.

3.1 OUTPUT VOLTAGE AND CURRENT

3. OUTPUT REQUIREMENTS

+12V1DC

+3.3V

+5V

+12V2DC

-12V

+5Vsb

1.0A

0.5A

0.3A

1.0A

0.0A

MINIMUM

LOAD

7.0A

10.0A

7.0A

8.5A

0.4A

1.25A

NORMAL

LOAD

18A

28A

30A

18A

0.5A

2.5A

±5%

±10%

±5%

±1%

±2%

±1%

120mV P-P

50mV P-P

120mV P-P

50mV P-P

120mV P-P

50mV P-P

120mV P-P

50mV P-P

MAXIMUM

LOAD

REG.

LINE

REG.

RIPPLE NOISE

(1) +3.3V &+5V total output not exceed 180W.

When +3.3V is load to 28A,the +5V maximum load is 17.52A.

When +3.3V is load to 9.0A,the +5V maximum load is 30A.

(2) +12V1DC & +12V2DC total output not exceed 348W.

(3) +3.3V &+5V & +12V1DC & +12V2DC total output not exceed 385W.

(4) All outputs shall be safety-isolated from the AC mains and share a common return.

This common return must be connected to supply chassis.

(5) Voltages and ripple are measured at the load side of mating connectors with a 0.1 uF

monolithic ceramic capacitor paralleled by a 10 uF electrolytic capacitor across the

measuring terminals.

STRIDER ST400

3.2 REMOTE ON/OFF CONTROL

3.3 OUTPUT VOLTAGE HOLD-UP TIME

3.4 OPERATION AT NO LOAD

The power supply shall accept a logic open collector level which will disable / enable

all the output voltage (exclude + 5V standby ).

As logic level is low, outputs voltage were enable.

As logic level is high, outputs voltage were disable.

Note: 1. Logic high level :3.50-5.25V while sourcing 0.4mA maximum.

2. Logic low level : 0-0.5V while sinking 1.5mA maximum.

3. Rise Time : 2ms maximum (10%-90%).

17.0 mS minimum : at 115V / 60 Hz. (COND.6)

17.0 mS minimum : at 230V / 50 Hz. (COND.6)

The power supply shall be capable of being operated with no load on any or all

outputs without damage. For no load on +3.3V&+5V, the output shall not exceed

+4.5 & +6.5Vdc and the power supply may shutdown and require by remote-control

or remove AC power restart.

COND.1

CONDITION

COND.2

COND.3

COND.4

COND.5

COND.6

COND.7

COND.8

COND.9

LOAD

11A

0.5A

3.0A

20A

28A

10A

12A

0.3A

3.0A

14A

10A

2.0A

1.0A

2.0A

5.0A

8.0A

13.0A

1.5A

1.0A

2.0A

4.0A

6.0A

12.0A

0.15A

0.3A

+3.3V +5V +12V1DC +12V2DC -12V

7.2A

16A

1.0A

10A

11.2A

2.0A

10.0A

11.2A

5.0A

15.0A

12.0A

4.0A

0.5A

0.3A

0.5A

1.0A

1.5A

2.0A

2.5A

1.0A

OUTPUT LOAD

NO.

LOAD REGULATION CHARACTERISTICS

+5Vsb

3.5.3 Short-Current Protection

A short circuit at any output shall cause no damage to the power supply nor blow the

primary fuse. The supply may shut down in the event of a short circuit and require

power-on restart. A short circuit consists of application of a test resistance of less

than 0.05 ohms at each output with maximum load on all outputs.

3.6 OUTPUT RISETIME

The cold-start enable output voltage risetime of all outputs shall be measured with

maximum load on all outputs.

risetime : +3.3V 20mS (maximum)

(10-95%) +5V 20mS (maximum)

+12 V1DC 20mS (maximum)

+12 V2DC 20mS (maximum)

-12 V 20mS (maximum)

+5Vsb 20mS (maximum)

3.5 PROTECTION

3.5.1 Over-voltage protection

In the event of an over-voltage condition on +3.3 & +5Vdc &+12V the power supply

shall

shutdown and require remote control or remove the AC mains input to reset the system.

+5V : 6.5V (maximum)

+3.3V : 4.6V (maximum)

+12V1DC : 15.5V (maximum)

+12V2DC : 15.5V (maximum)

3.5.2 Over-LOAD protection

There shall be protection from an output over-current event. The supply may shutdown

form such an event and require power-on restart. Testing consists of application of the

listed over-current value with maximum load on all other outputs.

Over-current test values: (maximum load)

+3.3V : 90A maximum

+5V : 68A maximum

+12V1DC : 32A maximum

+12V2DC : 32A maximum

STRIDER ST400

3.10 POWER ON TIME

115/230V (FULL LOAD) : 500mS minimum.

Figure 1

T2 : RISETIME < 20mS

T3 : POWER GOOD DELAY TIME 100mS-500mS

T4 : POWER GOOD RISETIMEɷ10mS

3.7 OUTPUT OVERSHOOT

No output voltage shall overshoot or generate spikes at turn-on or turn-off, during

momentary power loss, output short, or realistic input voltage or output load changes,

Overshoot is defined as any output that exceeds the voltage tolerance plus or minus

an additional 5%.

3.8 EFFICIENCY

Overall efficiency must be 70% minimum measured at normal AC mains voltage and

frequency with maximum loads on all outputs.

3.9 POWER GOOD SIGNAL

115/230V (FULL LOAD) : 100-500mS

4.3 SHOCK AND VIBRATION

The power supply will withstand the following imposed conditions without experiencing

non-recoverable failure or deviation form specified output characteristics. Storage -40G,

11mSec. half-sine wave pulse in both directions on three mutually perpendicular axes.

Operating -10G, 11mSec. half-sine wave pulse in both directions on three mutually

perpendicular axes.Vibration Operation-Sine wave excited, 0.25G maximum acceleration.

10-250 Hz, swept at one octave/min. Fifteen minute dwell at all resonant points, where

resonance is defined as those exciting frequencies at which the device under test

experiences excursions two times large than non-resonant excursions.

4. PHYSICAL ENVIRONMENT

4.1 OPERATING CONDITIONS

The power supply shall be capable of continuous operation and meet all electrical

specification without need for adjustment when subjected to the following

environmental conditions:

4.1.1 AMBIENT TEMPERATURE : 0 TO 50ʨ

The maximum continuous power rating of supply is 400W at 25ʨ. De-rate 2W / ʨ

from 25ʨto 50ʨ.

4.1.2 RELATIVE HUMIDITY : 90%

4.2 STORAGE AND SHIPPING CONDITIONS

No degradation of the power supply shall occur during shipping or storage at the

specified conditions.

4.2.1 AMBIENT TEMPERATURE : -20 TO +65ʨ

4.2.2 RELATIVE HUMIDITY : 95%

STRIDER ST400

6 OTHER REQUIREMENTS

6.1 COOLING

With the fan voltage set to around 12 volts, the fan will deliver greater than 38.2 CFM

with the power supply in open air.

6.2 INPUT CONNECTIONS

Refer to Mechanical Specifications for placement. The AC mains input are through a

three-circuit IEC type connector mounted on the rear of the power supply chassis.

5. REGULATORY COMPLIANCE

5.1 SAFETY REQUIREMENTS

-TUV EN60950

-UL 60950

5.2 DIELECTRIC STRENGTH

Primary to Frame Ground : 1800 Vac for 1 sec.

Primary to Secondary : 1800 Vac for 1 sec.

5.3 INSULATION RESISTANCE

Primary to Secondary : 20 Meg. ohms Minimum.

Primary to FRAME GROUND : 20 Meg. ohms Minimum.

5.4 GROUND LEAKAGE CURRENT

The power supply ground leakage current shall be less than 3.5mA.

5.5 EMISSION REQUIREMENTS

When testing the power supply must operate within the listed requirements.

6.4 PIN DEFINITION

M/B 24PIN connector

ATX 12V 4PIN connector

+3.3V

COM

+5VDC

COM

+5VDC

COM

PWRGOOD

+5Vsb

+12V

+3.3V

Orange

Black

Red

Black

Red

Black

Grey (24AWG)

Purple(18AWG)

Yellow

Orange

+3.3V

+3.3Vsense

-12VDC

COM

PS-ON

COM

N/C

+5VDC

COM

Orange (20AWG)

Brown (24AWG)

Blue (24AWG)

Black (18AWG)

Green (24AWG)

Black

N/C

Red

Black

18AWG wire Signal Pin Pin Signal 18AWG wire

Yellow / Black

18AWG wire Signal Pin Pin Signal 18AWG wire

+12V

Black

COM

6.3 RELIABILITY

The power supply reliability, when calculated by MIL-HDBK-217; latest revision, are

exceed 100,000 hours with all output at maximum load and an ambient temperature of 25ʨ.

STRIDER ST400

6PIN PCI Express Connector

Yellow

18AWG wire Signal Pin Pin Signal 18AWG wire

+12V

Black

GND

GND sense

GND

Fan voltage varies with the ambient temperature or output power.

7. FAN SPEED CONTROL

SATA connector

+3.3V

GND

+5V

GND

+12V

Orange

Black

Red

Black

Yellow

18AWG wire Signal Pin

4PIN peripheral connector (HDD) 4PIN floppy connector (FDD)

Yellow

Black

Red

18AWG wire Signal Pin Pin Signal 22AWG wire

+12V

COM

+5VDC

Red

Black

Yellow

+5VDC

COM

+12V

AIR FLOW

150.0

140.0

86.0

8. Power Supply Dimension : 150mm(W) ×86mm(H) ×140mm(D)

Tabla de contenidos

Otros manuales de Fuente de alimentación de SilverStone

SilverStone

SilverStone PSU Manual de usuario

SilverStone

SilverStone Lascala Series Manual de usuario

SilverStone

SilverStone SST-SX500-LG Manual de usuario

SilverStone

SilverStone GEMINI Series Manual de usuario

SilverStone

SilverStone GEMINI GM600-G Manual de usuario

SilverStone

SilverStone SFX Series Manual de usuario

SilverStone

SilverStone GEMINI Series Manual de usuario

SilverStone

SilverStone GEMINI Series Manual de usuario

SilverStone

SilverStone SST-ST1200-G Manual de usuario

SilverStone

SilverStone STRIDER TITANIUM SERIES Manual de usuario

SilverStone

SilverStone STRIDER PLATINUM SERIES Manual de usuario

SilverStone

SilverStone Gemini GM500-G Manual de usuario

SilverStone

SilverStone ST50F-ES Manual de usuario

SilverStone

SilverStone ST50NF Manual de usuario

SilverStone

SilverStone ST45SF Manual de usuario

SilverStone

SilverStone STRIDER SST-ST60F Manual de usuario

SilverStone

SilverStone ST70F-ES Manual de usuario

SilverStone

SilverStone STRIDER ESSENTIAL Series Manual de usuario

SilverStone

SilverStone STRIDER GOLD S Series Manual de usuario

SilverStone

SilverStone Decathlon Series Manual de usuario

SilverStone

SilverStone ST55F-G Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario