SilverNet MICRO TG60 Manual de usuario
V1.0 www.silvernet.com
SIL MICRO TG60 QUICK SETUP GUIDE
This guide will cover all the necessary steps to quickly configure, install and troubleshoot the
SilverNet MICRO TG60. It will be split into 3 sections: Installation, Configuration and
Common Problems.
FIRST GLANCE
Before beginning to install a link, you must ensure all the necessary equipment is in the box.
Please see below for package contents:
The box should contain the following: 1x Radio, 1x PoE Injector, 1x IEC C5 Power Cable, 1x
Steel-Band Clamps for Pole Mounting (3” Diameter Max), 2x Screws with Nylon Expansion
Plugs for Wall Mounting, 2x Cable Glands, 1x Quick Start Guide.
SIL MICRO TG60 Quick Setup Guide 2
OVERVIEW
#
Name
Description
1
Integrated Pole and
Wall Mounting Plate
Mounting plate containing 4x screw holes and 2x strap holes for
versatile mounting.
2
System LED Indicators
LAN: On (LAN Port Connection), Blinking: (Activity).
Uplink(PoE): On (Uplink PoE Port Active), Blinking (Activity). Slow Blink
during system boot up.
60G: On (60GHz Wireless Link Established), Blinking (Activity).
3
Grounding Screw
For ground wire connection.
4
LAN Port
Provides LAN Connectivity only.
5
Uplink PoE Port
Receives PoE Input from PoE Device and LAN Connectivity.
5
4
1
2
3
SIL MICRO TG60 Quick Setup Guide 3
INSTALLATION
Warning: For a safe and reliable installation, only use the provided accessories and screws.
Use of other accessories and screws could result in damage to the unit. Any damages
incurred by using unapproved accessories are not covered under warranty.
STEP 1: GROUND THE MICRO TG60
Ground the SIL TD60G by connecting a ground wire to the grounding point as shown above
to a nearby earth ground.
SIL MICRO TG60 Quick Setup Guide 4
STEP 2: ESTABLISH CONNECTIONS
Connect your outdoor-rated Cat5e or higher cable to the 1000BaseT RJ45 Uplink PoE port.
This port is capable of receiving PoE Input and LAN Traffic. Be sure to also install the included
weatherproof cable gland as shown above.
Optional: Using the LAN port, connect to a local LAN host. Be sure to also install the included
cable gland on this port as well.
SIL MICRO TG60 Quick Setup Guide 5
STEP 3: MOUNTING THE MICRO TG60 (POLE MOUNT)
Firstly, feed the steel-band clamp through the pole mount bracket points on the back of the
MICRO TG60 as shown above and lightly fasten them around the pole.
Next, align your MICRO TG60 with its partner radio. Once a good signal has been established,
tighten the clamps securely.
SIL MICRO TG60 Quick Setup Guide 6
MOUNTING THE MICRO TG60 (WALL MOUNT)
Begin by drilling two holes in the wall for the included expansion plugs. Insert the expansion
and both screws into the holes.
Align the MICRO TG60 mounting plate with the screws and then slide the radio down until it
snaps into its secured position.
SIL MICRO TG60 Quick Setup Guide 7
PRECISION BRACKET MOUNTING (OPTIONAL)
Two optional extra precision brackets (ordered separately) are designed for wall and pole
mounting and provide additional degrees of movement for antenna alignment.
SIL MICRO TG60 Quick Setup Guide 8
POWER
To begin, power up your device. Connect the other end of your Ethernet cable from the
Uplink PoE port to the PoE Injector (passive) which was provided in the box.
After you have connected your radio to the PoE Injector, verify that the power is On by
checking the LEDs on the back of the radio.
The Uplink (PoE) LED should blink
slowly during boot-up. Once the radio
is fully powered and idling, the LED
will remain static or intermittently
blink on traffic.
SIL MICRO TG60 Quick Setup Guide 9
CONFIGURATION
To first connect to your device, ensure you configure your network adapter to be within the
same subnet as the radio. For example, if using the radio’s LAN port, the radio is on IP
address 192.168.2.1 with a subnet mask of 255.255.255.0, you will need to configure your
adapter with an address of 192.168.2.X (where X can be 2-254) and a subnet mask of
255.255.255.0. If you are using the PoE Injector for connectivity, the radio will be on IP
address 192.168.1.20 with a subnet mask of 255.255.255.0, therefore you will need to
configure your adapter with an address of 192.168.1.X and a subnet mask of 255.255.255.0.
(Please note if using the PoE Port, the radio is configured as a DHCP client and will receive an
address from a DHCP server where applicable).
Once you have got this configured, enter the specified port IP address into your Web
Browser of choice URL bar. The default login details are as follows:
•Username: admin
•Password: password
Once logged in, you will need to configure your link. Please note that you only need to
configure the Link settings in one end of the link. The partner radio will automatically
connect.
SIL MICRO TG60 Quick Setup Guide
10
Step 1: If your radio has not been configured, login to your radio on 192.168.1.1 with the
above details.
Step 2: Navigate to “Network > Interfaces”. If configuring the client radio, simply leave the
radio on “Client Mode” and input your designated IP address then click “Save and Apply”.
Once this has been set, your client radio is fully configured.
Otros manuales para MICRO TG60
1
Tabla de contenidos
Otros manuales de Hardware de red de SilverNet
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
