Silicon Laboratories C8051F91 Series Manual de usuario

C8051F91x/90x

C8051F912 DEVELOPMENT KIT USER’SGUIDE

1. Relevant Devices

The C8051F912 Development Kit is intended as a development platform for the microcontrollers in the

C8051F91x-C8051F90x MCU family. The members of this MCU family are C8051F912, C8051F911, C8051F902,

and C8051F901.

Notes:

1. The target board included in this kit is provided with a pre-soldered C8051F912 MCU (QSOP24 package).

2. Code developed on the C8051F912 can be easily ported to the other members of this MCU family.

3. Refer to the C8051F91x-C8051F90x data sheet for the differences between the members of this MCU

family.

2. Kit Contents

The C8051F912 Development Kit contains the following items:

C8051F912 Target Board

C8051Fxxx Development Kit Quick-Start Guide

AC to DC Power Adapter

USB Debug Adapter (USB to Debug Interface)

2 USB Cables

2 AAA Batteries

CD-ROM

Figure 1. C8051F912 Target Board

C8051F91x/90x

2 Rev. 0.2

3. Hardware Setup Using a USB Debug Adapter

The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown

in Figure 2.

1. Connect the USB Debug Adapter to the DEBUG connector on the target board with the 10-pin ribbon

cable.

2. Connect one end of the USB cable to the USB connector on the USB Debug Adapter.

3. Verify that a shorting block is installed on J17 and that SW5 is in the ON position.

4. Connect the other end of the USB cable to a USB Port on the PC.

5. Connect the ac/dc power adapter to power jack P2 on the target board (Optional).

Notes:

Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter.

Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the

ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power

can damage the device and/or the USB Debug Adapter.

Figure 2. Hardware Setup Using a USB Debug Adapter

USB

Cable

AC/DC

Adapter

Target Board

P0.2 P0.3

2103

DEBUG

USB POWER

RESET

P1.6

P1.5

POWER OFF BEFORE

SW4

SWITCHING MODE

2 CELL 1 CELL

J17

IMEASURE

SILICON LABS

www.silabs.com

J6 VDD/DC+

J7 J13

F912

J14

J11

J10

VBAT

WALL_PWR

AAA_BAT

COIN_CELL

TOUCH SENSE SWITCH

P2.0 TOUCH SENSE SWITCH

P2.1

J15

J16

R15

J12J8

+3VD

+1VD

VBAT

SW5

OFF

Silicon Laboratories

USB DEBUG ADAPTER

Run

Stop Power

USB Debug

Adapter

C8051F91x/90x

Rev. 0.2 3

4. Software Setup

Simplicity Studio greatly reduces development time and complexity with Silicon Labs EFM32 and 8051 MCU

products by providing a high-powered IDE, tools for hardware configuration, and links to helpful resources, all in

one place.

Once Simplicity Studio is installed, the application itself can be used to install additional software and

documentation components to aid in the development and evaluation process.

Figure 3. Simplicity Studio

The following Simplicity Studio components are required for the C8051F912 Development Kit:

8051 Products Part Support

Simplicity Developer Platform

Download and install Simplicity Studio from www.silabs.com/8bit-software or www.silabs.com/simplicity-studio.

Once installed, run Simplicity Studio by selecting StartSilicon LabsSimplicity StudioSimplicity Studio

from the start menu or clicking the Simplicity Studio shortcut on the desktop. Follow the instructions to install the

software and click Simplicity IDE to launch the IDE.

The first time the project creation wizard runs, the Setup Environment wizard will guide the user through the

process of configuring the build tools and SDK selection.

In the Part Selection step of the wizard, select from the list of installed parts only the parts to use during

development. Choosing parts and families in this step affects the displayed or filtered parts in the later device

selection menus. Choose the C8051F91x family by checking the C8051F91x/90x check box. Modify the part

selection at any time by accessing the Part Management dialog from the WindowPreferencesSimplicity

StudioPart Management menu item.

Simplicity Studio can detect if certain toolchains are not activated. If the Licensing Helper is displayed after

completing the Setup Environment wizard, follow the instructions to activate the toolchain.

C8051F91x/90x

4 Rev. 0.2

4.1. Running Blinky

Each project has its own source files, target configuration, SDK configuration, and build configurations such as the

Debug and Release build configurations. The IDE can be used to manage multiple projects in a collection called a

workspace. Workspace settings are applied globally to all projects within the workspace. This can include settings

such as key bindings, window preferences, and code style and formatting options. Project actions, such as build

and debug are context sensitive. For example, the user must select a project in the Project Explorer view in order

to build that project.

To create a project based on the Blinky example:

1. Click the Simplicity IDE tile from the Simplicity Studio home screen.

2. Click the Create new project link from the welcome screen or go to FileNewSilicon Labs MCU

Project.

3. In the Kit drop-down, select C8051F912 Development Kit, in the Part drop-down, select C8051F912, and

in the SDK drop-down, select the desired SDK. Click Next.

4. Select Example and click Next.

5. Under C8051F912 Development Kit in the Blinky folder, select F912-902 Blinky and click Finish.

6. Click on the project in the Project Explorer and click Build, the hammer icon in the top bar. Alternatively,

go to ProjectBuild Project.

7. Click Debug to download the project to the hardware and start a debug session.

8. Press the Resume button to start the code running. The LED should blink.

9. Press the Suspend button to stop the code.

10. Press the Reset the device button to reset the target MCU.

11. Press the Disconnect button to return to the development perspective.

4.2. Simplicity Studio Help

Simplicity Studio includes detailed help information and device documentation within the tool. The help contains

descriptions for each dialog window. To view the documentation for a dialog, click the question mark icon in the

window:

This will open a pane specific to the dialog with additional details.

The documentation within the tool can also be viewed by going to HelpHelp Contents or HelpSearch.

C8051F91x/90x

Rev. 0.2 5

4.3. Legacy 8-bit IDE

Note: Using the Simplicity Studio tools with the C8051F912 Development Kit is recommended. See section 4. "Software

Setup‚" on page 3 for more information.

Download the 8-bit software from the website (www.silabs.com/8bit-software) or use the provided installer on the

CD-ROM to install the software tools for the C8051F91x/90x devices. After installation, examples can be found in

...\Examples\C8051F91x_90x in the installation directory. At a minimum, the C8051F912 DK requires:

Silicon Labs IDE—Software enabling initial evaluation, development, and debugging.

Configuration Wizard 2—Initialization code generation software for the C8051F91x/90x devices.

Keil C51 Tools—Keil 8051 Compiler/Assembler/Linker toolchain.

CP210x Drivers—Virtual COM Port (VCP) drivers for the CP210x COM interface. More information on this

installation process can be found in Section 4.4.

Other software available includes:

Keil µVision Driver—Driver for the Keil µVision IDE that enables development and debugging on

C8051Fxxx MCUs.

Flash Programming Utilities and MCU Production Programmer—Programming utilities for the

production line. More information on the available programming options can be found on the website:

http://www.silabs.com/products/mcu/Pages/ProgrammingOptions.aspx.

ToolStick Development Tools—Software and examples for the ToolStick development platform. More

information on this platform can be found at www.silabs.com/toolstick.

Also available on the 8-bit software webpage is the Battery Life Estimator, which gives designers a quick and easy

way to understand the discharge characteristics of different system configurations to help optimize low-power

applications.

The development kit includes the latest version of the C51 Keil 8051 toolset. This toolset is initially limited to a code

size of 2 kB and programs start at code address 0x0800. After registration, the code size limit is removed entirely

and programs will start at code address 0x0000.

To register the Keil toolset:

1. Find the Product Serial Number printed on the CD-ROM. If you no longer have this serial number,

2. Open the Keil µVision4 IDE from the installation directory with administrative privileges.

3. Select FileLicense Management to open the License Management window.

Figure 4. Keil µVision4 IDE License Management Window

C8051F91x/90x

6 Rev. 0.2

4. Click on the Get LIC via Internet... button to open the Obtaining a License IDE Code (LIC) window.

5. Press OK to open a browser window to the Keil website. If the window doesn’t open, navigate to

www.keil.com/license/install.htm.

6. Enter the Silicon Labs Product Serial Number printed on the CD-ROM, along with any additional required

information.

7. Once the form is complete, click the Submit button. An email will be sent to the provided email address

with the license activation code.

8. Copy the License ID Code (LIC) from the email.

9. Paste the LIC into the New License ID Code (LIC) text box at the bottom of the License Management

window in µVision4.

10. Press the Add LIC button. The window should now list the PK51 Prof. Developers Kit for Silabs as a

licensed product.

11. Click the Close button.

4.4. CP210x USB to UART VCP Driver Installation

The MCU Card includes a Silicon Labs CP210x USB-to-UART Bridge Controller. Device drivers for the CP210x

need to be installed before the PC software can communicate with the MCU through the UART interface. Use the

drivers included CD-ROM or download the latest drivers from the website (www.silabs.com/interface-software).

1. If using the CD-ROM, the CP210x Drivers option will launch the appropriate driver installer. If downloading

the driver package from the website, unzip the files to a location and run the appropriate installer for the

system (x86 or x64).

2. Accept the license agreement and follow the steps to install the driver on the system. The installer will let

you know when your system is up to date. The driver files included in this installation have been certified by

Microsoft.

3. To complete the installation process, connect the included USB cable between the host computer and the

COM PORT USB connector (J5) on the MCU Card. Windows will automatically finish the driver installation.

Information windows will pop up from the taskbar to show the installation progress.

4. If needed, the driver files can be uninstalled by selecting Windows Driver Package—Silicon

Laboratories... option in the Programs and Features window.

C8051F91x/90x

Rev. 0.2 7

4.5. Silicon Labs Battery Life Estimator

The Battery Life Estimator is a system design tool for battery operated devices. It allows the user to select the type

of battery they are using in the system and enter the supply current profile of their application. Using this

information, it performs a simulation and provides an estimated system operating time. The Battery Life Estimator

is shown in Figure 5.

Figure 5. Battery Life Estimator Utility

From Figure 5, the two inputs to the Battery Life Estimator are battery type and discharge profile. The utility

includes battery profiles for common battery types such as AAA, AA, A76 Button Cell, and CR2032 coin cell. The

discharge profile is application-specific and describes the supply current requirements of the system under various

supply voltages and battery configurations. The discharge profile is independent of the selected power source.

Several read-only discharge profiles for common applications are included in the pulldown menu. The user may

also create a new profile for their own applications.

To create a new profile:

1. Select the profile that most closely matches the target application or choose the "Custom Profile".

2. Click Manage

3. Click Duplicate

4. Click Edit

Profiles may be edited with the easy-to-use GUI (shown in Figure 6).

C8051F91x/90x

8 Rev. 0.2

Figure 6. Battery Life Estimator Discharge Profile Editor

The Discharge Profile Editor allows the user to modify the profile name and description. The four text entry boxes

on the left hand side of the form allow the user to specify the amount of time the system spends in each power

mode. On the right hand side, the user may specify the supply current of the system in each power mode.

Since supply current is typically dependent on supply voltage, the discharge profile editor provides two columns for

supply current. The V2 and V1 voltages at the top of the two columns specify the voltages at which the current

measurements were taken. The Battery Life Estimator creates a linear approximation based on the input data and

is able to feed the simulation engine with an approximate supply current demand for every input voltage.

The minimum system operating voltage input field allows the system operating time to stop increasing when the

simulated battery voltage drops below a certain threshold. This is primarily to allow operating time estimates for

systems that cannot operate down to 1.8 V, which is the voltage of two fully drained single-cell batteries placed in

series.

C8051F91x/90x

Rev. 0.2 9

The wakeup frequency box calculates the period of a single iteration through the four power modes and displays

the system wake up frequency. This is typically the "sample rate" in low power analog sensors.

Once the battery type and discharge profile is specified, the user can click the "Simulate" button to start a new

simulation. The simulation engine calculates the estimated battery life when using one single-cell battery, two

single-cell batteries in series, and two single-cell batteries in parallel. Figure 7 shows the simulation output window.

Figure 7. Battery Life Estimator Utility Simulation Results Form

The primary outputs of the Battery Life Estimator are an estimated system operating time and a simulated graph of

battery voltage vs. time. Additional outputs include estimated battery capacity, average current, self-discharge

current, and the ability to export graph data to a comma delimited text file for plotting in an external graphing

application.

C8051F91x/90x

10 Rev. 0.2

5. Target Board

The C8051F912 Development Kit includes a target board with a C8051F912 device pre-installed for evaluation and

preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping

using the target board. Refer to Figure 8 for the locations of the various I/O connectors. Figure 10 on page 12

shows the factory default shorting block positions.

P1 Expansion connector (96-pin)

P2 Power connector (accepts input from 7 to 15 VDC unregulated power adapter)

P3 USB connector (connects to PC for serial communication)

J1 Enable/Disable VBAT Power LED

J2, J3 Port I/O headers (provide access to Port I/O pins)

J5 Enable/Disable VDD/DC+ Power LED

J6 Provides an easily accessible ground clip

J7 Connects pin P0.7 (IREF0 Output) to resistor R14 and capacitor C19

J8 Connects P0.2 and P0.3 to switches and P1.5 and P1.6 to LEDs

J9 DEBUG connector for Debug Adapter interface

J10, J11 Selects the power supply source (Wall Power, AAA Battery, or Coin Cell)

J12 Connects Port I/O to UART0 interface

J13 Connects external VREF capacitor to the P0.0/VREF

J14 Connects the PCB ground plane to P0.1/AGND

J15 Connects negative potentiometer (R14) terminal to pin P1.4 or to GND

J16 Connects the potentiometer (R14) wiper to P0.6/CNVSTR

J17 Creates an open in the power supply path to allow supply current measurement

H1 Analog I/O terminal block

H2 Provides terminal block access to the input and output nodes of J17

SW4 Switches the device between one-cell (0.9–1.8 V supply) or two-cell (1.8–3.6 V) mode

SW5 Turns power to the MCU on or off

Figure 8. C8051F912 Target Board

P0.2 P0.3

Pin 1

Pin 2

2103

DEBUG

USB POWER

RESET

P1.6

P1.5

POWER OFF BEFORE

SW4

SWITCHING MODE

2 CELL 1 CELL

J17

IMEASURE

SILICON LABS

www.silabs.com

Pin 1

J6 VDD/DC+

J7 J13

J14

J11

J10

VBAT

WALL_PWR

AAA_BAT

COIN_CELL

TOUCH SENSE SWITCH

P1.0 TOUCH SENSE SWITCH

P1.1

P1.4

J15

GND

J16

R15

J12J8

+3VD

+1VD

VBAT

SW5

OFF

SW2 SW3

PORT1 SW1

PORT0

F912

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microcontrolador de Silicon Laboratories

Silicon Laboratories

Silicon Laboratories C8051F970 Manual de usuario

Silicon Laboratories

Silicon Laboratories ZIGBEE ETRX357 Manual de usuario

Silicon Laboratories

Silicon Laboratories AN1342 Manual de usuario

Silicon Laboratories

Silicon Laboratories EM34 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F912 Manual de usuario

Silicon Laboratories

Silicon Laboratories EFM8 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F530A Manual de usuario

Silicon Laboratories

Silicon Laboratories EFM8SB2 Manual de usuario

Silicon Laboratories

Silicon Laboratories EFR32xG21 Wireless Gecko Manual de usuario

Silicon Laboratories

Silicon Laboratories Z-Wave 800 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F38 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051T620 Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F53 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F360x-DK Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F35x Manual de usuario

Silicon Laboratories

Silicon Laboratories BRD4258B Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F02x-DK Manual de usuario

Silicon Laboratories

Silicon Laboratories UG338 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1010 Manual de usuario

Silicon Laboratories

Silicon Laboratories Giant Gecko EFM32GG Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F930 Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F41 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F36 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Telegesis ETRX357DVK Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario