Siklu EtherHaul 1200 Manual de usuario

EtherHaul 1200™

Gigabit Ethernet Wireless Solution

Installation and User Manual

EH-INST-02, Issue 4.0

December 2012

Installation and User Manual EtherHaul 1200™

Page 2 EH-INST-02, Issue 4.0

Trademarks

Siklu, the Siklu logo, and EtherHaul are all trademarks of Siklu Communication Ltd.

All other product names and trademarks mentioned in this document are trademarks or

registered trademarks of their respective companies.

Copyrights

No part of this publication may be reproduced or distributed in any form or by any

means, or stored in a database or retrieval system, without the prior written consent of

Siklu.

Disclaimers

The information contained in this document is subject to change without notice.

Siklu assumes no responsibility for any errors that may appear. Siklu makes no

warranties, expressed or implied, by operation of law or otherwise, relating to this

document, the products or the computer software programs described herein.

This document was originally written in English. Please refer to the English language

version for a full and accurate description of all products and services described herein.

Installation and User Manual EtherHaul 1200™

EH-INST-02, Issue 4.0 Page 3

Safety and Regulatory Notices

The following are mandatory notices for installation and operation of EtherHaul 1200™

70GHz Wireless Backhaul Link. Indications appearing here are required by the

designated government and regulatory agencies for purposes of safety and compliance.

General

Do not install or operate this System in the presence of flammable gases or fumes. Operating

any electrical instrument in such an environment is a safety hazard.

European Commission

This product has been designed to comply with CE markings in accordance with the

requirements of European Directive 1995/5/EC.

This product has been designed to comply with the requirements of European Directives.

This equipment must be permanently earthed for protection and functional purposes. To make a

protective earth connection, use the grounding point located on the System ODU using a

minimum amount of 16AWG grounding cable or according to local electrical code.

This apparatus is intended to be accessible only to authorized personnel. Failure to prevent

access by unauthorized personnel will invalidate any approval given to this apparatus.

This product is in full compliance with the following standards:

RF EN 302 217-3 1.3.1

EMC EN 301 489-4

Safety IEC 60950

Operation EN 300 019-1-4 Class 4.1E

Storage EN 300 019-1-1 Class 1.2

Transportation EN 300 019-1-2 Class 2.2

Installation and User Manual EtherHaul 1200™

Page 4 EH-INST-02, Issue 4.0

About this Document

This document is the Installation and User Manual for the EtherHaul 1200™ 70GHz

Wireless Link.

Audience

This document assumes a working knowledge of wireless backhaul platforms and their

operating environments.

This document is intended for use by all persons who are involved in planning, installing,

configuring, and using the EtherHaul system.

Conventions

The following conventions are used in this document in order to make locating, reading,

and using information easier.

Special Attention

Hint:

Informs you of a helpful optional activity that may be performed at the current

operating stage.

Note:

Provides important and useful information.

Caution:

Describes an activity or situation that may or will interrupt normal operation of the

EtherHaul system, one of its components, or the network.

Text Conventions

Document References

Italicized text is used to reference sections or chapters in this

document. In many cases, references use clickable hypertext links

that enable immediate access to referenced objects.

Command Input

Monospace text is used to help delineate command line user input

or text displayed in a command window.

Installation and User Manual EtherHaul 1200™

EH-INST-02, Issue 4.0 Page 5

TABLE OF CONTENTS

1Introduction to the EtherHaul™1200 System ............................................14

1.1 System Applications .................................................................................................15

1.2 Main Features ...........................................................................................................17

1.3 Functional Description..............................................................................................19

1.4 Licensing..................................................................................................................19

1.5 Management .............................................................................................................20

1.6 Technical Specifications............................................................................................21

2Installing the EtherHaul 1200......................................................................22

2.1 Preparing the Site......................................................................................................22

2.1.1 Physical and Environmental Requirements....................................................22

2.1.2 Cabling Requirements...................................................................................23

2.2 EtherHaul 1200 Package Contents.............................................................................23

2.3 Unpacking the EtherHaul 1200..................................................................................24

2.4 Required Tools..........................................................................................................24

2.5 Preparing for Installation...........................................................................................24

2.6 Mounting the EtherHaul 1200 ...................................................................................26

2.7 Connecting the Cables...............................................................................................28

2.7.1 Grounding the EtherHaul 1200 .....................................................................29

2.7.2 Power Supply Notes .....................................................................................29

2.7.3 Preparing the Cables.....................................................................................30

2.7.4 Removing Connectors from the EtherHaul ODU...........................................31

2.7.5 Connecting the Power...................................................................................31

2.7.6 Connecting Other Interfaces..........................................................................32

2.8 Aligning the Antenna................................................................................................32

2.8.1 Setting the ODU to Alignment Mode............................................................33

2.8.2 Performing the Alignment ............................................................................33

2.9 Performing Initial System Setup................................................................................35

3Performing Basic Configuration Using the Web EMS ..............................36

3.1 Connecting to the ODU Using the Web EMS ............................................................37

3.2 Saving Configuration Changes and Resetting the System Using the Web EMS..........37

3.3 Quick Configuration .................................................................................................38

3.4 Configuring and Displaying Basic System Information Using the Web EMS.............38

3.5 Configuring System IP Addresses Using the Web EMS.............................................39

3.6 Configuring Radio Parameters Using the Web EMS..................................................42

3.7 Viewing Modulation Profiles Using the Web EMS....................................................44

EtherHaul 1200™ Installation and User Manual

Page 6 EH-INST-02, Issue 4.0

3.8 Configuring Ethernet Interfaces Using the Web EMS................................................44

3.9 Configuring SNMP Settings......................................................................................46

3.10 Default VLAN Setting ..............................................................................................47

4Performing Basic Configuration using the CLI .........................................48

4.1 Establishing a CLI Session with the ODU .................................................................48

4.2 Saving Configuration Changes and Resetting the System Using the CLI....................49

4.3 Configuring and Displaying Basic System Information Using the CLI.......................49

4.4 Configuring System IP Addresses Using the CLI.......................................................50

4.5 Configuring Radio Parameters Using the CLI............................................................51

4.5.1 Displaying Radio Parameters and Status Using the CLI ................................52

4.5.2 Configuring the Radio Parameters Using the CLI..........................................52

4.5.3 Viewing Modulation Profiles Using the CLI .................................................53

4.6 Configuring Ethernet Interfaces Using the CLI..........................................................54

4.6.1 Configuring Interface Parameters..................................................................54

4.6.2 Displaying Interface Status...........................................................................54

4.7 Default VLAN Setting ..............................................................................................55

5Commissioning and Acceptance Procedure.............................................56

5.1 Installation Verification and Testing..........................................................................56

5.1.1 Physical Installation Verification ..................................................................56

5.1.2 RF Link Test ................................................................................................56

5.1.3 Link Errors Test............................................................................................57

5.1.4 Ethernet Services Test ..................................................................................57

5.1.5 Management Verification .............................................................................57

5.1.6 Recording ODU Configuration .....................................................................57

5.2 EtherHaul Commissioning and Acceptance Form......................................................58

6EtherHaul Networking Configuration.........................................................62

6.1 Provider Bridge.........................................................................................................62

6.2 EtherHaul Bridging Model........................................................................................63

6.3 Configuring VLANs .................................................................................................64

6.3.1 Transparent Bridge Mode .............................................................................64

6.3.2 Configuring VLANs Using the Web EMS ....................................................66

6.3.3 Configuring VLANs Using the CLI ..............................................................67

6.4 Configuring Bridge Ports ..........................................................................................70

6.4.1 Configuring Bridge Ports Using the Web EMS .............................................70

6.4.2 Configuring Bridge Ports Using the CLI .......................................................71

6.4.3 Configuring the Bridging Port.......................................................................72

6.5 Configuring Provider Bridge and Advanced VLAN Settings .....................................73

6.5.1 Configuring PEP Virtual Ports......................................................................73

6.5.2 S-VID Translation Table...............................................................................74

Installation and User Manual EtherHaul 1200™

EH-INST-02, Issue 4.0 Page 7

6.5.3 C-VLAN Registration Table.........................................................................75

6.5.4 VLAN-to-SNMP ifTable ..............................................................................76

6.5.5 SNMP ifTable Attributes ..............................................................................76

6.5.6 Forwarding Data Base (FDB)........................................................................76

6.5.7 FDB Address Table ......................................................................................76

7Performing Advanced Configuration.........................................................78

7.1 Configuring Quality-of-Service.................................................................................78

7.1.1 QoS Classification........................................................................................79

7.1.2 Metering and Coloring..................................................................................82

7.1.3 QoS Scheduling............................................................................................83

7.2 Configuring CFM (Connectivity Fault Management).................................................86

7.2.1 CFM Overview.............................................................................................87

7.2.2 Working with Maintenance Domains............................................................88

7.2.3 Working with Maintenance Associations ......................................................89

7.2.4 Working with Component Maintenance Associations....................................89

7.2.5 Working with Maintenance End Points (MEPS)............................................90

7.2.6 Working with Peer MEPs .............................................................................92

7.2.7 Working with CCM Messages ......................................................................93

7.2.8 Working with Linktrace Messages................................................................94

7.2.9 Sample CFM Configuration..........................................................................95

7.3 Configuring Link OAM...........................................................................................103

7.3.1 Enabling Link OAM...................................................................................103

7.3.2 Link OAM Discovery.................................................................................104

7.3.3 Link OAM Loopback .................................................................................104

7.4 Configuring Synchronous Ethernet (SyncE) ............................................................106

7.4.1 SyncE Overview.........................................................................................106

7.4.2 SyncE Configuration ..................................................................................107

7.4.3 Typical SyncE Scenario..............................................................................109

7.4.4 SyncE Alarms.............................................................................................113

7.5 Configuring Ethernet Ring Protection (ERP)...........................................................114

7.5.1 Supported ERP Features .............................................................................114

7.5.2 ERP Ring Commands.................................................................................115

7.5.3 ERP Administrative Commands..................................................................116

7.5.4 ERP Timers................................................................................................117

7.5.5 ERP Configuration Example.......................................................................117

8Monitoring the System ..............................................................................119

8.1 Viewing Active Alarms...........................................................................................119

8.2 Viewing Alarm History and System Events.............................................................120

8.3 Events Configuration (Masking)..............................................................................120

8.4 Viewing Radio Statistics .........................................................................................122

EtherHaul 1200™ Installation and User Manual

Page 8 EH-INST-02, Issue 4.0

8.4.1 Viewing Radio Statistics Using the Web EMS ............................................122

8.4.2 Viewing a Statistics Summary Using the Web EMS....................................123

8.4.3 Viewing Radio Statistics Using the CLI......................................................124

8.4.4 Viewing Radio Statistics Summary Using the CLI ......................................125

8.5 Viewing VLAN Statistics........................................................................................125

8.6 Viewing Queue Statistics ........................................................................................126

8.6.1 Viewing Outgoing Queue Statistics.............................................................126

8.6.2 Incoming Queues Commands .....................................................................127

8.7 Viewing Ethernet Statistics .....................................................................................127

8.7.1 Viewing Ethernet Statistics Using the Web EMS ........................................127

8.7.2 Viewing Ethernet Statistics Using the CLI ..................................................128

8.8 Viewing Bandwidth Utilization Statistics ................................................................128

9Performing System Administration..........................................................130

9.1 Configuring Encryption...........................................................................................131

9.1.1 Loading Encryption License Key................................................................131

9.1.2 Setting up a Static Key................................................................................131

9.2 Working with Configuration Files ...........................................................................132

9.2.1 Saving Configurations ................................................................................132

9.2.2 Viewing Configurations..............................................................................132

9.2.3 Restoring the Default Configuration............................................................132

9.2.4 Rollback Operations ...................................................................................133

9.3 Configuring Users...................................................................................................133

9.4 Upgrading the ODU Software .................................................................................135

9.4.1 Upgrading the ODU Software Using the Web EMS ....................................136

9.4.2 Upgrading the ODU Software Using the CLI..............................................137

9.5 Monitoring CLI Sessions.........................................................................................138

9.6 Viewing System Inventory......................................................................................138

9.6.1 Viewing System Inventory Using the Web EMS.........................................139

9.6.2 Viewing System Inventory Using the CLI...................................................139

9.7 Upgrading the License Key.....................................................................................140

9.8 Performing Address Translation..............................................................................141

9.9 Siklu File System (SFS)..........................................................................................142

9.9.1 Understanding SFS.....................................................................................142

9.9.2 Specifying Files Using URLs......................................................................142

9.9.3 File System Commands ..............................................................................143

9.9.4 SFS Examples ............................................................................................144

9.10 Command Line Scripts............................................................................................144

9.10.1 Displaying Scripts ......................................................................................144

9.10.2 Running Scripts..........................................................................................145

9.10.3 Adding Scripts............................................................................................145

9.10.4 Viewing Script Content...............................................................................146

Installation and User Manual EtherHaul 1200™

EH-INST-02, Issue 4.0 Page 9

9.10.5 Command Line Scripts using the CLI .........................................................147

9.11 Configuring NTP ....................................................................................................147

9.11.1 NTP Configuration .....................................................................................147

9.12 Viewing User Activity Log .....................................................................................148

9.13 Managing SNMP ....................................................................................................150

9.13.1 SNMP Managers ........................................................................................150

9.13.2 SNMP Agent Communities.........................................................................151

9.13.3 SNMPv3 Users Settings..............................................................................151

10 EtherHaul Diagnostics...............................................................................153

10.1 The Troubleshooting and Diagnostics Process.........................................................153

10.2 EtherHaul ODU LEDs ............................................................................................155

10.3 EtherHaul System Alarms and Events .....................................................................156

10.4 EtherHaul System Statistics.....................................................................................159

10.4.1 RF Statistics ...............................................................................................159

10.4.2 VLAN Statistics .........................................................................................160

10.4.3 Ethernet Statistics.......................................................................................160

10.5 EtherHaul System Loopbacks..................................................................................161

10.5.1 Loopback Diagrams....................................................................................161

11 Using the EtherHaul CLI............................................................................164

11.1 Invoking the CLI.....................................................................................................164

11.2 CLI Command Syntax.............................................................................................165

11.2.1 Basic Conventions......................................................................................165

11.2.2 Common Syntax Rules ...............................................................................166

11.2.3 Repeatedly Used Identifiers ........................................................................166

11.2.4 CLI Command Types .................................................................................167

11.2.5 Designating Objects in CLI Commands ......................................................170

11.2.6 Designating Named Objects........................................................................171

11.3 Viewing the CLI Command History........................................................................174

11.4 Invoking CLI Help and Autocompletion..................................................................174

11.5 CLI Error Messages ................................................................................................176

11.6 Viewing the EtherHaul Statistics History.................................................................177

11.6.1 Using Statistics Intervals.............................................................................177

11.7 CLI Managed Object Reference ..............................................................................178

11.8 Management Object Attributes................................................................................179

11.8.1 System Object Attributes ............................................................................179

11.8.2 Physical Inventory Object Attributes...........................................................181

11.8.3 Physical Inventory Entities .........................................................................187

11.9 Radio Object Attributes...........................................................................................192

11.9.1 RF Object Attributes...................................................................................192

11.9.2 Radio Statistics...........................................................................................194

EtherHaul 1200™ Installation and User Manual

Page 10 EH-INST-02, Issue 4.0

11.10 Encryption Object Attributes...................................................................................195

11.11 Connectivity Fault Management (CFM) Object Attributes.......................................196

11.11.1 Maintenance Domain (MD) Object Attributes.............................................196

11.11.2 Maintenance Association (MA) Object Attributes.......................................197

11.11.3 Component MA Object Attributes...............................................................197

11.11.4 Maintenance End Point (MEP) Object Attributes ........................................199

11.11.5 CCM Message Object Attributes.................................................................204

11.11.6 Peer MEP Object Attributes........................................................................205

11.11.7 Peer MEP Database Attributes....................................................................205

11.11.8 LTR Object Attributes ................................................................................208

11.12 Network Object Attributes ......................................................................................211

11.12.1 Ethernet Interface Attributes .......................................................................211

11.12.2 Ethernet Statistic Descriptions ....................................................................217

11.12.3 Bridge Object Attributes.............................................................................218

11.12.4 Bridging Port Object Attributes...................................................................218

11.12.5 Outgoing Queue Object Attributes..............................................................221

11.12.6 Incoming Queue Object Attributes..............................................................221

11.12.7 IP Object Attributes ....................................................................................222

11.12.8 VLAN Common Table Attributes ...............................................................222

11.12.9 VLAN Table Attributes ..............................................................................223

11.12.10 C-LAN Registration Table Attributes.....................................................224

11.12.11 PEP Virtual Port Table Attributes...........................................................225

11.12.12 S-VID Translation Table Attributes........................................................226

11.12.13 SNMP ifTable Attributes........................................................................227

11.12.14 Forwarding Data Base (FDB) Object Attributes .....................................229

11.12.15 FDB Address Table Attributes ...............................................................230

11.12.16 ARP Table Attributes.............................................................................232

Appendix A: Installing the ODU with a Two Foot Antenna.............................233

Otros manuales para EtherHaul 1200

Tabla de contenidos

Otros manuales de Enrutador de red de Siklu

Siklu

Siklu EtherHaul-1200TX Manual de usuario

Siklu

Siklu EtherHaul-5500FD Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad