SIIG Low Profile PCI-1P Manual de usuario

Low Profile PCI-1P

Quick Installation Guide

04-0332A

Introducing the Low Profile PCI-1P

TheLowProfilePCI-1PconformstothenewPCIcardform

factor standard made for space constrained system

designs. It provides 1 ECP/EPP parallel port which

supports data transfer rates up to 1.5 MB/sec.

FeaturesandBenefits

•Conforms to PCI v2.2 Plug and Play

•Can be installed in 32-/64-bit, 3.3v/5v PCI and

PCI-X slots

•Full support for DOS and Windows based software

•PCI IRQ sharing feature reduces IRQ conflicts

• Compliant with IEEE 1284-1994 parallel port

standard

• Supports ECP/EPP, Bi-directional (PS2) and

Standard Parallel Port (SPP) modes

• Works with various types of parallel devices

including printers, removable drives, scanners,

CD-R/RWs, and more...

• Dimensions:

-PCB:119.91mm(L) x 64.41mm(H)

- Bracket:18.42mm(W) x 79.20mm(H)

SystemRequirements

•Pentium or equivalent computer with an available

PCI slot

•DOS, Windows 95/98/98 SE/ME/NT 4.0/2000/

XP/Server 2003

PackageContents

• (1) Low Profile PCI-1P board

• (1) Driver CD

• This quick installation guide

Layout

Figure 1. Low Profile PCI-1P Layout

Hardware Installation

General instructions for installing the card are provided

below, since the design of computer cases and

motherboards vary. Refer to your computer’s reference

manual for further information, if needed.

Caution: Static Electricity Discharge may permanently

damage your system. To avoid possible static electricity

discharge during the installation, please follow the

guidelines below:

•Discharge any static electricity build up in your

bodybytouchingalargegroundedmetalsurfaceor

thecomputer’scase(ifpluggedin),forafewseconds.

Parallel Port

•During the installation, avoid any contact with

internal parts. Handle cards only by their external

edges.

1. Turn OFF the power to your computer.

2. Unplugthepowercordandremoveyourcomputer's

cover.

3. Remove the slot bracket from an available PCI slot.

4. CarefullyalignthecardtotheselectedPCIslotpush

the board down firmly, but gently, until it is well

seated.

Figure 2. Inserting the PCI Board

5. Replace the slot bracket's holding screw to secure

the card.

6. Replacethecomputercoverandreconnectthepower

cord.

Software Installation

This section provides the steps on how to install the

Low Profile PCI-1P drivers. Please make sure the board is

installed before proceeding with the driver installation.

Windows95DriverInstallation

1. At the Update Device Driver Wizard, click Next.

2. Insert the driver CD and click Other Locations.

3. Type in X:\1P\95, click OK, then click Finish.

(Change X: to match your CD-ROM drive letter)

4. From the Insert Disk window, click OK. When the

CopyingFilesdialogboxappears,typeinX:\1P\95,

then click OK. (Change X: to match your CD-ROM

drive letter)

5. RestartWindowstocompletethedriverinstallation.

Windows98/98SEDriverInstallation

1. At the Add New Hardware Wizard, click Next.

2. Select Search for the best driver for your device

(Recommended), then click Next.

3. Select Specify a location, uncheck the other boxes,

insert the driver CD, type in X:\1P\98, then click

Next. (Change X: to match your CD-ROM drive

letter)

4. Click Next, then Finish.

5. RestartWindowstocompletethedriverinstallation.

WindowsMEDriverInstallation

1. AttheAddNewHardwareWizard,chooseSpecify

the location of the driver (Advanced), then click

Next.

2. Check Specify a location, uncheck the other box,

insert the driver CD, type in X:\1P\ME, then click

Next. (Change X: to match your CD-ROM drive

letter)

3. Click Next, then Finish.

4. RestartWindowstocompletethedriverinstallation.

WindowsNT4.0DriverInstallation

1 From the desktop, click Start,then Run.

2. Insert the driver CD, type X:\1P\NT4\setup.exe,

then click OK. (Change X: to match your CD-ROM

drive letter)

3. At the Welcome window, click Continue.

4. Atthe Multi-IODriversSetupwindow,clickNext.

5. SelectYesandclickFinishtorestartNTtocomplete

the driver installation.

Windows2000DriverInstallation

1. At the Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(Recommended), then click Next.

3. SelectSpecifythelocation,unchecktheotherboxes,

then click Next.

4. Insert the driver CD, type in X:\1P\2000, then click

OK. (Change X: to match your CD-ROM drive

letter)

5. Click Next, then click Finish to complete the driver

installation.

WindowsXPDriverInstallation

1. AttheFoundNewHardwareWizard,chooseInstall

from a list or specific location (Advanced), then

click Next.

2. Insert the driver CD, check Include this location in

thesearch,unchecktheotherbox,typeinX:\1P\XP,

thenclickNext. (ChangeX:tomatchyourCD-ROM

drive letter)

3. At the Hardware Installation window, click

Continue Anyway, then click Finish.

Note:OurdriverhasbeenthoroughlytestedinWindows

forstabilityandcompatibility.

4. Repeat steps 1-3.

5. Restart your system for the new setup to take effect.

WindowsServer2003DriverInstallation

1. AttheFoundNewHardwareWizard,chooseInstall

from a list or specific location (Advanced), then

click Next.

2. Insert the driver CD, check Include this location in

the search, uncheck the other box, type in

X:\1P\2003, then click Next. (Change X: to match

your CD-ROM drive letter)

3. At the Hardware Installation window, click

Continue Anyway, then click Finish.

Note:OurdriverhasbeenthoroughlytestedinWindows

forstabilityandcompatibility.

4. Repeat steps 1-3.

5. Restart your system for the new setup to take effect.

DOSDriverInstallation

1. Insert the driver CD. From the C:\> prompt, type

copy X:\1P\dos\*.*,and press <Enter>. (Change

X: to match your CD-ROM drive letter)

2. Type edit autoexec.bat, and press <Enter>.

3. Add C:\nmdosin.exe -a at the bottom of the

autoexec.bat file.

4. Go to File, save the changes and exit.

5. Restart your system for the new setup to take effect.

VerifyProperWindowsDriverInstallation

For Windows 95/98/98 SE/ME:

1. Right click My Computer, click Properties, click

Device Manager.

2. Double click Multi-function adapters or

NetMosMultiFunction, NetMos PCI...Controller

should be listed.

3. Double click Ports (COM & LPT), a NetMos PCI

Parallel Port should be listed.

For Windows NT 4.0:

1. Click Start, Settings, Control Panel.

2. Double click NetMos Multi-I/O Ports icon, click

Parallel Port tab, a parallel port should be listed

under Ports.

For Windows 2000/XP/Server 2003:

1. Right click My Computer, click Manage, then click

Device Manger.

2. Double click Multifunction adapters, NetMos...

Parallel Port should be listed.

3. Double click Ports (COM & LPT), a NetMos PCI

Parallel Port should be listed.

Troubleshooting

Problem:Iaminstallingaparallelport(s)and my system

freezes up when Windows tries to install the driver for

my printer port.

Solution:Enteryoursystembios,settheonboardparallel

port I/O address to 278h, save and exit. In certain

systems, the address 278h is reserved for ISA boards. So

when the PCI parallel port tries to capture this address,

your system gets confused and freezes up.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers!

Simply visit our Web site at www.siig.com and click on

Support. Our online support database is updated daily with

new drivers and solutions. The answers to your problems

could be just a few clicks away.

If you can't find answers or solutions to your questions, you

have an option to submit the problems online to one of our

technical support analysts and we will promptly respond to

you with answers or solutions.

The5-yearmanufacturerwarrantysuppliedwiththisproduct

is offered by SIIG, Inc. If you should happen to encounter

anyproblems with this product, please follow theprocedures

below.

1. If it is within the store's return policy period, please

return the product to the store where you purchased

from.

2. If your purchase has passed the store's return policy

period, please contact SIIG. See SIIG's Limited 5-year

Warranty card for more information.

Online Store

SIIG offers all of our products online at our company

store. Visit us at http://onlinestore.siig.com to find

our complete line of products, including hard to find

itemsandaccessories(poweradapters,cables,upgrade

kits, etc.).

LowProfilePCI-1PisatrademarkofSIIG,Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. DOS, Windows and Windows NT are

registeredtrademarksofMicrosoftCorporation. PentiumisaregisteredtrademarkofIntelCorporation.

Othernamesusedinpublicationareforidentificationonlyandmaybetrademarksoftheirrespective

companies.

PRODUCT NAME MODEL NUMBER

Low Profile PCI-1P LP0404

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

About SIIG, Inc.

Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer

ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel

ports,USB,SerialATA&UltraATAcontrollers,FireWire(1394a/b),

Networking,SoundCards,andotheraccessories. SIIGisthepremier

one-stopsourceofupgrades.

SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly

features, and all products are backed by a 5-year manufacturer

warranty. High-qualitycontrolstandardsareevidentbytheoverall

easeofinstallationandcompatibilityofourproducts,as well as one

ofthelowestdefectivereturnratesintheindustry. SIIGproductscan

be found in most computer retail stores, mail order catalogs, and e-

commercesitesintheAmericasandtheUK,aswellasthroughmajor

distributors,systemintegrators,andVARs.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Tarjeta PCI de SIIG

SIIG

SIIG RS232 Serial Manual de usuario

SIIG

SIIG Cyber 1S1P PCI Manual de usuario

SIIG

SIIG JJ-P49012-S6 Manual de usuario

SIIG

SIIG VV-CV0012-S1 Manual de usuario

SIIG

SIIG 4-Port RS232 Serial PCI with 16550 UART Manual de usuario

SIIG

SIIG SC-SA2012-S1 Manual de usuario

SIIG

SIIG PCI Express Serial Cards Manual de usuario

SIIG

SIIG Universal PCI Serial Cards Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Manual de usuario

SIIG

SIIG Cyber 2S1P 950 PCI Manual de usuario

SIIG

SIIG Serial ATA 4-Channel PCI Manual de usuario

SIIG

SIIG SC-SA4M12 Manual de usuario

SIIG

SIIG NN-830012-S2 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Manual de usuario

SIIG

SIIG SC-SAE412-S3 Manual de usuario

SIIG

SIIG 1394 PCI Adapter Manual de usuario

SIIG

SIIG SC-SA3012-S1 Manual de usuario

SIIG

SIIG DP CyberSerial 4S PCIe Manual de usuario

SIIG

SIIG NN-83M012-S2 Manual de usuario

SIIG

SIIG CyberPro PCI 4S Manual de usuario

SIIG

SIIG 1394 PCI Adapter Manual de usuario

SIIG

SIIG CyberPro PCI 1S Manual de usuario

SIIG

SIIG JJ-P02012 Manual de usuario

SIIG

SIIG USB 2.0 Video Capture Device Manual de usuario

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario

Pyle

Pyle Gamelink PLINK1 Manual de usuario

Alpha Networks

Alpha Networks WMP-A13V Manual de usuario