Signet 8860 Manual de usuario

CAUTION!

• Remove power to unit before wiring input and output connections.

• Follow instructions carefully to avoid personal injury.

• This product should only be used for the purposes and in the manner described in this manual.

Signet 8860 Dual Channel Conductivity/Resistivity Controller

Installation

1. Punch out panel and de-burr edges. Recommended clearance on all sides between instruments is 1 inch.

2. Place gasket on instrument, and install in panel.

3. Slide mounting bracket over back of instrument until quick-clips snap into latches on side of instrument.

4. Connect wires to terminals.

5. To remove, secure instrument temporarily with tape from front or grip from rear of instrument. DO NOT RELEASE. Press

quick-clips outward and remove.

6. If cleaning is necessary, wipe the front of the unit with a damp cloth.

7. The live contacts on the back of this unit must be covered to avoid accidental shock hazard.

Speciﬁcations

General

Compatible electrodes: Signet 2819 to 2823 (Standard or

Certiﬁed Cond/Resist Sensors)

Enclosure:

• Rating: NEMA 4X/IP65 front (NEMA 4X Rear cover available)

• Case: PBT

• Panel case gasket: Neoprene

• Window: Polyurethane-coated polycarbonate

• Keypad: Sealed 4-key silicone rubber

• Weight: 8860-AC: 1.28 lb/0.58 kg 8860: 1.2 lb/0.55 kg

Display (Alphanumeric 2 x 16 LCD) :

• Contrast: User selected, 5 levels

• Update rate: 1.5 seconds

Sensor input range:

• Conductivity: 0.01 μS/cm to 400 000 μS/cm

• Resistivity: 10 KΩ•cm to 100 MΩ•cm

• TDS: 0.023 to 200 000 PPM nominal (adjustable μS/PPM)

• Temperature:

-25 to 120°C (-13 to 248°F) PT 1000; 25ºC = 1096Ω

Accuracy:

• Conductivity/Resistivity: ± 2% of reading

• Temperature: ± 0.5ºC (0 to 100ºC)

Electrical

Power requirements:

3-8860-AC: 100 to 240 VAC ± 10% , 50-60 Hz, 20VA or

11 to 24 VDC ±10%, regulated, 0.5 A max

3-8860: 11 to 24 VDC ±10%, regulated, 0.5 A max

Three 4 to 20 mA Outputs:

• Passive, isolated, fully adjustable and reversible

4 to 20 mA outputs are independently source selectable

• Max loop impedance:

150 Ω@ 12 V, 450 Ω@ 18 V, 750 Ω@ 24 V

• Update rate: ~100 mS

• Accuracy: ±0.03 mA @ 25°C, 24 VDC

Open-collector outputs (2 available, optically isolated):

• 50 mA sink or source, 30 VDC max. pull-up voltage

• Programmable for:

• High or Low setpoint with adjustable hysteresis

• Pulse operation (max. rate: 400 pulses/min)

• USP standards

• Time delay: 0 to 6400 s.

Relay outputs (up to 4 SPDT relays available )

• Maximum resistive load: 5 A @ 250 VAC, 5 A @ 30 VDC

• Isolation between open contacts: 500 V minimum

• Programmable for:

• High or Low setpoint with adjustable hysteresis

• Pulse operation (max. rate: 400 pulses/min)

• USP standards

• Time delay: 0 to 6400 s

Environmental

• Ambient operating temperature: -10 to 55°C (14 to 131°F)

• Storage temperature: -15 to 80°C (5 to 176°F)

• Relative humidity: 0 to 95%, non-condensing

• Maximum altitude: 2000 m (6562 ft)

• Insulation category: II

• Pollution degree: 2

Standards and Approvals

• CE

• EN61326: Immunity & Emissions for Control Equipment

• EN61010: Safety

• UL listed

• Manufactured under ISO 9001, ISO 14001

• Chinese RoHS

For detailed information go to www.gfsignet.com

Signet

Conductivity/Resistivity

Transmitter

C1 23.45 µS

C2 8.72 µS

Relay 1 Relay 2

ENTER

102 mm

(4.0 in.)

56 mm

(2.2 in.)

Panel Cutout

92 x 92 mm

(+ 0.8, - 0 mm)

3.6 x 3.6 in.

(+0.031, -0 in.)

Optional

Rear Cover

quick-clip

gasket on

front side

of panel

panel

terminals

mounting

bracket

RELAY1

RELAY2

RELAY3 RELAY4

N/C N/O COM N/C N/O COM N/C N/O COM N/C N/O COM

RELAY3,4

OPEN

COLL 3,4

-OPEN COLL 4

OPEN COLL 3

SHLD

ISOGND

TEMP1

SGNL1

SHLD

ISOGND

TEMP2

SGNL2

POWER

OUTPUTOPTION

96mm (3.8 in.)

96 mm

(3.8 in.)

3-8860.090 Rev. F 2/08 English

*3-8860.090*

English

28860 Dual Channel Conductivity/Resistivity Controller

Electrical Connections

Caution: Failure to fully open terminal jaws before removing wire may permanently damage instrument.

This product must be provided with a means to disconnect all current carrying conductors connected to the main AC line, or,

as part of the building installation.

Wiring Procedure

1. Remove 0.35- 0.47 in. (9-12 mm) of insulation from wire end.

2. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

3. Insert exposed (non-insulated) wire end in terminal hole until it bottoms out.

4. Release orange terminal lever to secure wire in place. Gently pull on each wire to ensure a good connection.

Wiring Removal Procedure

1. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

Wiring Tips:

• Do not route sensor cable in conduit containing AC power wiring - electrical noise may interfere

with sensor signal.

• Routing sensor cabling in grounded metal conduit may prevent moisture damage, electrical

noise, and mechanical damage.

• Seal cable entry points to prevent moisture damage.

• Do not insert two wires into a single terminal. If necessary, splice the wires together before

inserting into the terminal.

RELAY 1

RELAY 2

RELAY 3 RELAY 4

N/C N/O COM N/C N/O COM N/C N/O COM N/C N/O COM

RELAY 3,4

OPEN

COLL 3,4

- OPEN COLL 4

+OPEN COLL 4

- OPEN COLL 3

+OPEN COLL 3

-LOOP 2

+LOOP 2

-LOOP 3

+LOOP 3

-LOOP 1

+LOOP 1

SHLD

ISO GND

TEMP 1

SGNL 1

SHLD

ISO GND

TEMP 2

SGNL 2

POWER

OUTPUT OPTION

11 - 24V

0.5 A

3-8860.610 D

100 - 240V

50-60Hz, 20VA

LISTED

E171559

LR92369

Internal open-collector

output circuit

Outputs

Caution:

Electrical shock hazard exists!

♦

Never connect live AC lines to the

instrument.

♦

Always connect a ground wire to

the ground terminal when using

AC power.

Output Option Switch

• In OPEN COLLECTOR position, relays 3 and 4 are open

collector outputs as shown.

• In RELAY 3, 4 position, relays 3 and 4 are dry contact relays

identical to relays 1 and 2.

• The menu references in the 8860 display will not change.

Outputs 3 and 4 will be identiﬁed as "Relay" regardless of

switch setting.

4 to 20 mA loop Outputs

The current loops in the 8860 are passive circuits.

12-24 VDC must be provided from an external source.

A single loop is illustrated for clarity.

PLC or Recorder

Power

Supply

12-24 VDC

Loop 1

Loop 2

Loop 3

+ + +

- -

Channel 3

4-20 mA in

Channel 1

4-20 mA in

Channel 2

4-20 mA in

8860 4 to 20 mA outputs

38860 Dual Channel Conductivity/Resistivity Controller

Sensor Input Connections

• The 8860 will accept two independent sensor input signals.

The two sensors may be of different cell constant values.

• Do not route sensor cable in any conduit containing AC power

wiring - electrical noise may interfere with the signal.

• Cable shield MUST be maintained through cable splice.

• Use three conductor shielded cable for cable extensions up

to 30 m (100 ft) max. for measurements below 10 MΩ(above

0.10 μS).

• Maximum cable length for resistivity measurements above

10 MΩ is 25 ft, and solution temperatures must be between

20°C and 100°C.

Relay and Open Collector Functions

The 8860 is equipped with 4 SPDT relays that can be conﬁgured

for High alarm, Low alarm, Proportional pulse or USP operation.

• Low: Output triggers when process variable is less than

setpoint.

• High: Output triggers when process variable is higher than

setpoint.

• Off: Disables output pulse.

• Pulse Operation

The output emits a 100 mS pulse at a rate deﬁned by the

Source, Pulse Range and Max PlsRate settings, and by the

process condition. The maximum pulse rate is 400 pulses per

minute.

Example: As the process falls below 10 μS the output will

start pulsing in relation to the process value, the max pulse

endpoint and the programmed pulses/min. Pulse rate

will increase as the process approaches the programmed

endpoint.

SHLD

ISO GND

TEMP 2

SGNL 2

SHLD

ISO GND

TEMP 1

SGNL 1

RED

WHITE

BLACK

SILVER (SHLD) RED

WHITE

BLACK

SILVER (SHLD)

Hysteresis

Time

Low Setpoint

Process

Relay energized

Relay relaxed

Hysteresis

Time

High Setpoint

Process

5Relay 1 Rng: μS

10.00 -->5.00 >

Relay/Open Collector PlsRate:

100 Pulses/min >

10 μS = 0 pulses/min.

7.5 μS = 50 pulses/min.

5 μS = 100 pulses/min.

RANGE defines where the pulsing starts

and where it reaches the maximum rate.

Pulse rate

µS ----->

0 pulses

100 pulses

The Pulse Rate determines what the

maximum rate will be. The 8860 maximum

capability is 400 pulses per minute.

1μS

1MΩ

10μS

100KΩ

1,000μS 10,000μS

50,000μS 200,000μS

100μS

10KΩ

400,000μS

100,000μS

0.054μS

18.3 MΩ

Bottled

Water

Brackish Sea Water

(Salinity)

UPW @ 25°C

USP

Cooling Tower

Waste Waters

Deionization Regen. Chemicals

Alkali Cleaners, Acids/Bases

Rinse

Water

3-2819, 3-2839 (0.01 Cell)

3-2820, 3-2840 ( 0.10 Cell)

3-2821, 3-2841 (1.0 Cell)

3-2822, 3-2842 (10.0 Cell)

3-2823 (20.0 Cell)

0.010μS

100 MΩ

200μS

48860 Dual Channel Conductivity/Resistivity Controller

Monitor C1 Conductivity and C2 Conductivity simultaneously. This is the

permanent display when Channel 2 is ON.

Monitor Channel 1 Conductivity and Channel 1 Temperature. This is the

permanent display when Channel 2 is OFF.

Monitor Channel 2 Conductivity and Channel 2 Temperature. This view is

available only when Channel 2 is ON.

Monitor Percent Reject, Difference, or Ratio

(Channel 1 to Channel 2 or Channel 2 to Channel 1)

Monitor Loop 1 and Loop 2 current output simultaneously.

Monitor Loop 3 and status of Relays 3 and 4 (Open Collector 3 and 4).

Monitor date for scheduled maintenance or date of last calibration.

Signet

Conductivity/Resistivity

Transmitter

C1 23.45 µS

C2 8.72 µS

Relay 1 Relay 2

ENTER

VIEW menu

• During normal operation, the ProcessPro displays the VIEW menu.

• When using the CALIBRATE or OPTIONS menus, the ProcessPro will return to the VIEW

menu if no activity occurs for 10 minutes.

• To select the item you want displayed, press the UP or DOWN arrow keys. The items

will scroll in a continuous loop. Changing the display selection does not interrupt system

operations.

• No keycode is necessary to change display selection.

• Output settings cannot be edited from the VIEW menu.

View Menu

Display Description

The VIEW displays below are temporary. The permanent display will return after 10 minutes

C1 1000.00 μS/cm

C2 30.00 μS/cm

C1 1000.00 μS/cm

25.0 ºC

C2 30.00 μS/cm

25.0 ºC

Reject C1 →C2

97.00

Loop 1 12.03 mA

Loop 2 5.69 mA

Loop 3 13.7 mA

R3 ON R4 PLS

Last Cal

04-20-08

58860 Dual Channel Conductivity/Resistivity Controller

Notes on Steps 5 and 6:

• All output functions remain active during editing.

• Only the ﬂashing element can be edited.

• RIGHT ARROW key advances the ﬂashing element in a continuous loop.

• Edited value is effective immediately after pressing ENTER key.

• If no key is pressed for 10 minutes unit will restore the last saved value and return to step 3.

• Step 6 (pressing ENTER key) always returns you to Step 3.

• Repeat steps 3-6 until all editing is completed.

Notes on Step 2:

If no key is pressed for 5 minutes while display is showing "Enter

Key Code", the display will return to the VIEW menu.

Notes on Steps 3 and 4:

• Refer to pages 6 and 7 for complete listing of menu items and their use.

• From the Step 3 display, pressing the UP and DOWN keys simultaneously will

return the display to the VIEW menu.

• If no key is pressed for 10 minutes, display will also return to the VIEW menu.

ProcessPro Editing Procedure:

Step 1. Press and hold ENTER key:

• 2 seconds to select the CALIBRATE menu.

• 5 seconds to select the OPTIONS menu.

Step 2. The Key Code is UP-UP-UP-DOWN keys in sequence.

• After entering the Key Code, the display will show the ﬁrst item in the selected menu.

Step 3. Scroll menu with UP or DOWN arrow keys.

Step 4. Press RIGHT ARROW key to select menu item to be edited.

• The ﬁrst display element will begin ﬂashing.

Step 5. Press UP or DOWN keys to edit the ﬂashing element.

• RIGHT ARROW key advances the ﬂashing element.

Step 6. Press ENTER key to save the new setting and return to Step 3.

OPTIONS

CALIBRATE

VIEW

2s 5s

Press &

hold for

access:

ENTER

Step 5

Step 6

Notes on Step 1:

• The View Menu is normally displayed.

• The CALIBRATE and OPTIONS menus require a KEY CODE.

Step 4

First item in CALI-

BRATE menu

Step 3

Step 3: Finished Editing?

Press the UP and DOWN keys simultaneously after

saving the last setting to return to normal operation.

Press the UP and DOWN keys simultaneously

while any element is ﬂashing. This will recall the

last saved value of the item being edited and

return you to Step 3.

Step 5: Made an Error?

20.00 u

Relay1 Setpnt:

20.00 uS

Relay1 Setpnt:

10.00 uS

ENTER

Relay1 Setpnt:

10.00 uS

Relay Setpnt:

.00 uS

Relay1 Setpnt:

Saving

Relay1 Setpnt:

19.00 uS >

20.00 us >

Relay 1 Setpnt:

Standard >

Chan 1 Cell:

CALIBRATE:----

EnterKey Code

CALIBRATE:*---

EnterKey Code

CALIBRATE:**--

EnterKey Code

CALIBRATE:***-

EnterKey Code

Standard >

Chan 1 Cell:

68860 Dual Channel Conductivity/Resistivity Controller

Select CUSTOM only if you are connecting a certiﬁed conductivity sensor. Select

STANDARD for all non-certiﬁed sensors.

For STANDARD sensors: Select the nominal cell constant: 0.01, 0.1, 1.0, 10.0 or 20.0.

For CUSTOM sensors: Enter the precise cell constant from the certiﬁcate provided with your

sensor, or from the information label on the sensor.

Adjust the temperature of the system based on an accurate external reference.

This single-point wet calibration procedure requires a test solution of known value.

Enter all zeroes here to restore TEMPERATURE and CONDUCTIVITY to factory calibration.

Select the units of measure: μS/cm, mS/cm, kΩ•cm, MΩ•cm, PPB, PPM

If the Units selection is PPM or PPB, set the ratio of μS to Total Dissolved Solids. The factory

preset value is 2 μS per 1 PPM of TDS. (Always μS/PPM, even if units is PPB).

See page 10 for additional information.

Select a functional relationship between C1 and C 2: • Ratio is (C1:C2) or (C2:C1)

• Percent Reject is 100%(1-C2/C1) or 100%(1-C1/C2) • Difference is (C1-C2) or (C2-C1)

Select the measured value or calculated FUNCTION you want Loop 1 to represent:

Chan 1 Cond, Chan 2 Cond, Chan 1 Temp, Chan 2 Temp, or Function

Set the minimum (4 mA =) and maximum (20 mA =) range for Loop 1.

Make sure that the values are consistent with the units of the source.

Select operating mode for Relay 1: OFF, LOW, HIGH, USP or PULSE.

For USP mode: • Relay 1 SOURCE must be Cond 1 or Cond 2

• Temp Comp (Options menu) must be set to None

Select the INPUT SIGNAL (or FUNCTION) monitored by Relay 1:

• Cond 1 • Cond 2 • Temp 1 • Temp 2 • Function

Set Relay 1 activation point. The maximum value acceptable is 999999.

USP setpoints are high alarms, where the setpoint is a percentage below the USP limit.

Relay 1 will be deactivated at setpoint ± Hysteresis (depending on High or Low selection).

When the relay Mode is USP (deﬁned as a HIGH alarm), Hysteresis is displayed in μS.

Set up to 6400 seconds delay time for relay response.

Relay 1 will be activated only if the source value exceeds the setpoint for this time period.

If Relay 1 is PULSE mode, set the start and end point of the conductivity range and also set

the maximum pulse rate. (The maximum PULSE rate setting is 400 pulses per minute.)

The combined Relay 1 Range and Pulse rate settings shown here indicate:

"Start pulsing when the conductivity value is 10 μS and increase the pulse rate up to the

maximum of 120 pulses per minute when the conductivity value reaches 40 μS"

Use this "notepad" to record important dates, such as annual recertiﬁcation or scheduled

maintenance.

Chan 1 Cell:

Standard >

Chan 1 Cell:

1.0 >

Cell: Custom

1.0000 >

Chan 1 Set:

Temperature >

Chan 1 Set:

Conductivity >

Chan 1 Units:

uS/cm >

Chan 1 TDS:

2.0000 uS/PPM >

Function:

Reject C1 →C2 >

Loop 1 Source:

Chan 1 Cond >

Loop 1 Range: uS

0.0000 →100.000 >

Relay 1 Mode:

Low >

Relay 1 Source:

Chan 1 Cond >

Relay 1 Setpnt:

10.0000 uS >

Relay 1 Hys:

0.5000 uS >

Relay 1 Delay:

10.0 secs >

Relay 1 Rng: uS

10.0000 →40.0000 >

Relay 1 PlsRate:

120 Pulses/Min >

Last CAL:

04-20-08 >

Calibrate Menu

Display

(Factory settings shown) Description

• All changes in this menu become effective when saved, except the "Set Cond" and "Set Temp" settings.

• All outputs affected by a change in the "Set Cond" and "Set Temp" settings are frozen until you exit the Calibrate menu.

78860 Dual Channel Conductivity/Resistivity Controller

0 to < 5ºC 0.6

5 to < 10ºC 0.8

10 to < 15ºC 0.9

15 to < 20ºC 1

20 to < 25ºC 1.1

25 to < 30ºC 1.3

30 to < 35ºC 1.4

35 to < 40ºC 1.5

40 to < 45ºC 1.7

50 to < 55ºC 1.8

55 to < 60ºC 2.1

60 to < 65ºC 2.2

65 to < 70ºC 2.4

70 to < 75ºC 2.5

75 to < 80ºC 2.7

80 to < 85ºC 2.7

85 to < 90ºC 2.7

90 to < 95ºC 2.7

95 to < 100ºC 2.9

100 to < 105ºC 3.1

The USP limit

(μS) is:

When the

temperature

range is:

USP Limits

USP (United States Pharmacopoeia) has deﬁned a set of conduc-

tivity values (limits) to be used for pharmaceutical water moni-

toring. This standard requires non-temperature compensated

conductivity measurement be used to warn if the conductance

approaches the USP limit. The limits vary according to the tem-

perature of the sample.

The 8860 has the USP limits stored in memory. It will automati-

cally determine the proper USP limit based on the measured

temperature.

Using the USP function

In the 8860, USP setpoints are deﬁned as a percentage below

the USP limit, so a USP alarm is always a HIGH alarm. The 8860

can be set to warn you if the conductivity approaches within a set

percentage of the USP limit.

The following settings and conditions are required for a USP

relay function:

1. In the CALIBRATE menu:

• RELAY MODE must be set to USP.

• RELAY SOURCE must be Chan 1 or Chan 2 Cond.

• SOURCE UNITS must be set to μS.

2. In the OPTIONS menu:

• The TC Mode of the USP channel must be set to None.

(Service tip: If a relay is constantly on when it should be off,

check the relay settings listed above.)

Example:

• The USP setpoint is 40%.

• The water temperature is 19ºC, so the USP limit is 1.0 μS.

• The relay will be activated when the conductivity value reaches

0.6 μS, or 40% below the 1.0 USP limit.

• If the water temperature drifts to more than 20ºC, the 8860 will

automatically adjust the USP limit to 1.1.

• The relay will now be activated when the conductivity value

reaches 40% below 1.1 μS, or 0.66 μS.

88860 Dual Channel Conductivity/Resistivity Controller

Contrast:

3 >

Temp Display:

ºC >

Channel 2:

On >

Power:

60 Hz >

Chan 1 TC Mode:

Linear >

Chan 1 TC Slope:

0.00 % >

Averaging:

Off >

Chan 1 Decimal:

*.**** >

Loop 1 Adjust:

4.00 mA >

Loop 1 Adjust:

20.00 mA >

Relay 3 Active:

High >

Test Loop 1:

Test Relay 1:

Adjust the LCD contrast for best viewing. A setting of 1 is lower contrast, 5 is higher. In

general, select lower contrast if the display is in warmer ambient surroundings.

Select ºC or ºF.

Turn CH 2 OFF if not in use. This will remove all menu functions related to CH 2.

Select 50 Hz or 60 Hz electrical noise suppression, according to the AC power used in your

area. Select the proper setting for all applications, whether AC or DC powered.

Set the method for temperature compensation to NONE, LINEAR or PURE WATER. You

must select NONE for USP systems. Select LINEAR for applications where the water is

less than 5 MΩ(or greater than 0.2 μS). Select PURE WATER for applications where the

water is greater than 5 MΩ(or less than 0.2 μS).

For LINEAR or PURE WATER temperature compensation, select a % per ºC slope.

Maximum slope setting is 9.99 % per ºC. If Temp Comp setting is NONE, this item will not

be displayed.

OFF provides the most instantaneous response to process changes. Select LOW (4 sec)

or HIGH (8 sec) averaging if your process experiences frequent or extreme ﬂuctuations.

Set the decimal to the best resolution for your application. The display will automatically

scale up to this restriction. Select *****., ****.*, ***.** **.*** or *.****

Adjust the minimum and maximum current output. The display value represents the precise

current output. Adjustment limits:

• 3.80 mA < 4.00 mA > 5.00 mA

• 19.00 mA < 20.00 mA > 21.00 mA

Use this setting to match the system output to any external device.

These settings repeat for Loop 2 and Loop 3.

Select active HIGH or active LOW operation for relay 3

Recommended: Use active LOW if OUTPUT OPTION switch is set for OPEN

COLLECTOR operation.

Active HIGH: Power is applied to relay coil when process value reaches SETPOINT.

Active LOW: Power is removed from relay coil when process value reaches SETPOINT.

Press UP and DOWN keys to manually change Loop 1output current.

Limits are 3.6 mA to 21.00 mA. Hold UP or DOWN keys to scroll the output value.

Press UP and DOWN keys to manually toggle the relay state.

Options Menu

Display

(Factory settings shown) Description

Notes:

Channel settings will repeat when Channel 2 is enabled.

Loop settings will repeat for Loop 2 and Loop 3.

Check setting for related values when making changes (for example, if temp is set for ºC with a temp alarm at 25ºC, and you change

the temp to ºF, be sure to change the alarm setpoint to 77ºF.)

Relay settings will repeat for Relays 2, 3 and 4 (except "Relay Active" selection; applies to Relay 3 and 4 only.)

98860 Dual Channel Conductivity/Resistivity Controller

Calibration Procedure

The 8860 has been electronically calibrated at the factory.

• Procedure A veriﬁes the accuracy and linearity of the 8860 by simulating temperature and conductivity values with precision (±0.1%)

ﬁxed resistors.

• Procedure B is a wet calibration. This procedure uses the sensor input and NIST traceable test solutions.

A) Accuracy Veriﬁcation with Precision Resistors (Electronic Calibration):

1. Simulate the Temperature

The temperature input to the 8860 is a PT-1000 thermistor, where 1000 Ohms (Ω) is equal to 0ºC and a change of 3.84 Ωequals a

1ºC change. (1000 Ω= 0ºC, 1003.84 Ω= 1.0ºC, 1007.68 Ω= 2.0ºC...................1096 Ω= 25ºC)

• Connect a resistor (1000 Ωto 1096 Ω) between "Temp" and "Iso. Gnd" terminals.

• Set Temp; Adjust the temperature to exact value based on the measured resistance. (See Editing Procedure, Calibrate menu).

• To verify the 8860 temperature linearity, connect a second resistor value to the terminals.

• If the 8860 does not display the correct value, service is required. ( ± 0.5ºC)

2. Simulate the Conductivity

You may calculate the exact Resistance needed to simulate a speciﬁc conductivity value , or you may calculate the exact Conductivity

based on a resistor value:

Resistance = Cell constant e.g. 0.1 Cell = 5,000 Ωor 5 KΩ

conductivity (Siemens*) 0.000020 (Siemens*)

Conductivity = Sensor cell e.g. 0.1 Cell = 0.000001 Siemens*

Simulation resistance (Ω) 100,000 (Ω) or 1μS/cm

(*1 μS = 1 X 10-6 Siemens or 0.000001 Siemens)

• Connect the conductivity resistor between the "Sgnl 1 " and "Iso Gnd" (or Sgnl 2 and Iso Gnd) terminals.

• Set Cond: Adjust the conductivity value based on the resistor value. (See Editing Procedure and Calibrate menu).

• Verify the linearity of the 8860 by connecting a second Conductivity resistor of a different value.

• If the 8860 does not display the correct value (± 2% of reading), service is required.

B) Wet Calibration with NIST Traceable Solutions:

When using NIST traceable standards, review the temperature information provided with the test solution. Prevent contamination of the

test solution. The sensor must be at the temperature speciﬁed on the test solution label.

• Remove the sensor from the system. Rinse the sensor in a small amount of test solution.

• Place the sensor into the test solution.

• Place a reference thermometer into the same solution.

• Allow sufﬁcient time for the temperature to stabilize.

• Set Temp: Adjust the temperature value based on the reference thermometer. (See Editing Procedure.)

• Set Cond: Adjust the conductivity value based on the test solution value. (See Editing Procedure.)

• Verify the linearity of the 8860 by placing the sensor into a second test solution of a different value.

• If the 8860 does not display the correct value (Temperature ± 0.5ºC, Conductivity ± 2% of reading), service is required.

10 8860 Dual Channel Conductivity/Resistivity Controller

TDS Factor

Some industries need to display a conductivity value as Total

Dissolved Solids (TDS), measured in units of parts per million

(PPM) or parts per billion (PPB).

• 1 PPM is equivalent to 1 mg per liter.

• 1 PPB is equivalent to 1 μg per liter.

• The 8860 calculates PPM or PPB by dividing the μS value

by a TDS Factor that you deﬁne. TDS factors can vary

widely, ranging from 1.50 to 2.50 μS per PPM. Methods

for establishing a TDS factor are beyond the scope of this

manual.

• The 8860 will accept TDS factor values from 0.01 to 99999.9

μS per PPM.

(factory preset = 2.00 μS per PPM)

NOTE: The 8860 TDS factor must be set in PPM.

TDS Factor = Conductivity (μS) ÷Total dissolved solids (PPM)

PPM = Solution conductivity (μS) ÷ TDS Factor

Example:

• Solution conductivity = 150 μS

• TDS = 80 PPM

• TDS Factor = 150 μS ÷ 80 PPM = 1.88 μS per

PPM

Temperature Effects

Conductivity measurement is highly dependent on temperature.

The basic rule is that higher temperatures result in greater

conductance (less resistance).

Temperature effects are expressed as the percentage of

conductivity change (in μS) per °C. The conductivity value is

generally referenced to 25ºC. The 8860 has three temperature

compensation options:

None

USP standards for pharmaceutical waters require that the

measurement be made without temperature compensation. USP

limits are discussed on page 7.

Pure Water (Standard Compensation)

This selection is used for measurements of very clean water,

less than 0.2 μS. Temperature effects are not linear in this

range, so the temperature coefﬁcient is not easily determined.

This selection is recommended for all Resistivity applications

measuring from 5 MΩto 18MΩ. This selection conforms to ASTM

standard D1125 and D5391.

Linear

This selection allows you to calculate a custom temperature

compensation value for Conductivity measurements in the range

of 0.2 μS and greater (Resistivity applications measuring less

than 5 MΩ). The procedure is outlined in the section on the right.

Calculating a Linear Temperature Coefﬁcient

1. Set TC Mode to NONE (see OPTIONS menu, page 8).

2. Heat a sample solution close to the maximum process

temperature. Place sensor in the sample solution and

allow several minutes for stabilization. Record the 8860

temperature and conductivity values in the spaces provided:

Displayed temperature: T1 = _______ °C

Displayed conductivity: C1 = _______ μS

3. Cool the sample solution close to the minimum process

temperature. Place sensor in the sample solution allowing

several minutes for stabilization. Record displayed

temperature and conductivity values in the spaces provided:

Displayed temperature: T2 = _______ °C

Displayed conductivity: C2 = _______ μS

(A 10% change in conductivity between steps 2 and 3 is

recommended.)

4. Substitute recorded readings (steps 2 and 3) into the following

formula:

TC Slope = 100 x (C1 - C2)

(C2 x (T1 - 25)) - (C1 x (T2 - 25))

Example: A sample solution has a conductivity of 205 μS @

48°C. After cooling the solution, the conductivity was measured

at 150 μS @ 23°C. (C1 = 205, T1 = 48, C2 = 150, T2 = 23)

The TC is calculated as follows:

TC Slope = 100 x (205 - 150) =5500 = 1.42%/°C

(150 x (48 - 25)) - (205 x (23 - 25)) 3860

Tabla de contenidos

Otros manuales de Controladores de Signet

Signet

Signet 8900 Manual de usuario

Signet

Signet 8900 Manual de usuario

Signet

Signet GF 5600 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario