SignaMax 065-7714HSFPTB Manual de usuario
Hardened Managed Ethernet Switch
1
This Gigabit Ethernet SFP media converter is a plug-and-play device. Connect the supplied AC
to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter,
and then attach the plug into a standard AC outlet with a voltage range from 100 to 240V AC.
DIP Switch
DIP
switch
Up (Default Setting) Down
Left-hand
side
The fiber port auto detects
full and half duplex
Forces the fiber port to full
duplex mode
Right-hand
side
Disable LFS Enable LFS LFS:
Link fault signaling
function
The 1000BaseT and 1000BaseSX/LX Connectors
The 1000BaseT
Connection
The following lists the pinouts of the
1000BaseT port.
The 1000BaseSX/LX
Connection
The SFP socket accepts standard Gigabit
Ethernet Small Form-factor Pluggable (SFP)
modules of various types and spectra.
The Port Status LEDs
ription
DIP switch configuration for Link Fault Signaling
enable/disable and fiber auto/force mode.
Signamax™Connectivity Systems
Hardened Managed Ethernet Switch
Model - 065-7714HSFPTB
User’s Guide
Hardened Managed Ethernet Switch
2
Quick Start Guide
This quick start guide describes how to install and use the
Hardened Managed Ethernet Switch. This is the switch of
choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
LED State Indication
10/100BaseTX
Steady A valid network connection established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Communication speed is 100Mbps.
10/100
Off Communication speed is 10Mbps.
10/100/1000BaseTX, 1000BaseSX/LX
Steady A valid network connection established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Communication speed is 1000Mbps.
1000
Off Communication speed is 10/100Mbps.
Steady A valid network connection established.
SFP Link
Off No valid network connection established.
Hardened Managed Ethernet Switch
3
Power Input Assignment
Power3 12VDC DC Jack
＋12-32VDC
Power1
－Power Ground
Power2
＋12-32VDC
Earth Ground
Terminal Block
There are two pairs of power inputs can be used to power up this switch.
Redundant power supplies function is supported.
Options A-Terminal Block power supplies, part numbers: DC-1824-30W;
DC-1824-60W; DC-1824-75W; DC-1824-120W
Options B- DC Jack power supply
※Signamax strongly recommends the use of a terminal block power
supply; however, a jack for power is also provided. Please see the
pinout chart below for use when wiring a power jack for this equipment:
Output No. Name
PIN 1 V+
PIN 2 GND
PIN 3 NC
Hardened Managed Ethernet Switch
4
Functional Description
Meets NEMA TS1/TS2 Environmental requirements such as
temperature, shock, and vibration for traffic control equipment.
Meets EN61000-6-2 EMC Generic Standard Immunity for industrial
environment.
Manageable via SNMP, Web-based, Telnet, and RS-232 console port.
Support 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:
10/100/1000Mbps, full/half-duplex; Auto MDI/MDIX.
1000Base-SX/LX: Multi mode or Single mode SC type; WDM Single
mode SC type.
Support 8192 MAC addresses. Provides 2M bits memory buffer.
Operating voltage and Max. current consumption: 1.25A @ 12VDC,
0.625A @ 24VDC. Power consumption: 15W Max.
Power Supply: Redundant DC Terminal Block power inputs or 12VDC
DC JACK with 100-240VAC external power supply.
-40℉to 167℉(-40℃to 75℃) operating temperature range.
Tested for functional operation @ -40℉to 185℉(-40℃to 85℃).
Supports Din-Rail, Panel, or Rack Mounting installation.
Hardened Managed Ethernet Switch
5
Console Configuration
Connect to the switch console:
Connect the DB9 null-modem or cross over cable to the RS-232 serial
port of the device and the RS-232 serial port of the terminal or computer
running the terminal emulation application. Direct access to the
administration console is achieved by directly connecting a terminal or a
PC equipped with a terminal-emulation program (such as
HyperTerminal) to the switch console port.
Configuration settings of the terminal-emulation program:
Baud rate: 115,200bps
Data bits: 8
Parity: none
Stop bit: 1
Flow control: none.
Press the “Enter” key. The Command Line Interface (CLI) screen should
appear as below:
Logon to Exec Mode (View Mode):
At the “switch_a login:” prompt just type in “root” and press <Enter> to
logon to Exec Mode (or View Mode). And the “switch_a>” prompt will
show on the screen.
Logon to Privileged Exec Mode (Enable Mode):
Hardened Managed Ethernet Switch
6
At the “switch_a>” prompt just type in “enable” and press <Enter> to
logon to Privileged Exec Mode (or Enable Mode). And the “switch_a#”
prompt will show on the screen.
Logon to Configure Mode (Configure Terminal Mode):
At the “switch_a#” prompt just type in “configure terminal” and press
<Enter> to logon to Configure Mode (or Configure Terminal Mode). And
the “switch_a(config)#” prompt will show on the screen.
Hardened Managed Ethernet Switch
7
Web Configuration
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web
browser. A login window will be shown as below:
Enter the factory default login ID: root.
Enter the factory default password (no password).
Then click on the “Login” button to log on to the switch.
Hardened Managed Ethernet Switch
8
Preface
This manual describes how to install and use the Hardened
Managed Ethernet Switch. This switch introduced here is
designed to deliver full scalability with SNMP/RMON
web-based management functions by providing:
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Features on the Hardened Managed Ethernet Switch
Illustrative LED functions
Installation instructions
Management Configuration
SNMP, DHCP, IGMP…
Specifications
Hardened Managed Ethernet Switch
9
Table of Content
DIP Switch .................................................................................. 1
The 1000BaseT and 1000BaseSX/LX Connectors..................... 1
The Port Status LEDs................................................................. 1
Description ......................................................................... 1
Quick Start Guide .................................................................................................................... 2
Physical Description..........................................................2
The Port Status LEDs and Power Inputs .................................... 2
Functional Description...................................................... 4
Console Configuration.......................................................5
Web Configuration............................................................ 7
Preface .................................................................................................................................... 9
Table of Contents .................................................................................................................. 10
Product Overview .................................................................................................................. 13
Hardened Managed Ethernet Switch............................. 13
Package Contents............................................................. 13
Product Highlights........................................................... 14
Basic Features........................................................................... 14
Management Support................................................................ 15
Front Panel Display......................................................... 16
Physical Ports................................................................... 17
Switch Management ........................................................ 17
Web-based browser interface ................................................... 18
Administration console via RS-232 serial port (CLI)............... 18
External SNMP-based network management application ........ 18
Installation ............................................................................................................................. 19
Selecting a Site for the Switch......................................... 19
Connecting to Power........................................................ 19
DC Terminal Block power input.............................................. 19
12VDC DC Jack....................................................................... 19
Hardened Managed Ethernet Switch
10
Connecting to Your Network.......................................... 20
Cable Type & Length............................................................... 20
Cabling ..................................................................................... 20
Switch Management .............................................................................................................. 21
Management Access Overview....................................... 21
Administration Console (CLI)........................................21
Direct Access............................................................................ 22
Modem Access ......................................................................... 22
Web Management............................................................23
SNMP-Based Network Management............................. 23
Protocols........................................................................... 24
Management Architecture.............................................. 24
Web-Based Browser Management........................................................................................ 25
SNMP & RMON Management............................................................................................... 26
Overview........................................................................... 26
SNMP Agent and MIB-2 (RFC 1213)............................ 26
RMON MIB (RFC 1757) and Bridge MIB (RFC 1493)27
RMON Groups Supported........................................................ 28
Bridge Groups Supported......................................................... 29
Web-Based Browser Management........................................................................................ 30
Logging on to the switch..................................................30
Understanding the Browser Interface............................ 31
Trunking........................................................................... 45
STP.................................................................................... 48
VLAN................................................................................ 56
QoS.................................................................................... 61
SNMP................................................................................ 64
Other Protocols................................................................ 68
Command Line Console Management .................................................................................. 72
Tabla de contenidos
Otros manuales de Enrutador de red de SignaMax
SignaMax
SignaMax 065-7700 Manual de usuario
SignaMax
SignaMax 065-7418POETB Manual de usuario
SignaMax
SignaMax 065-7405TB Manual de usuario
SignaMax
SignaMax 065-7012G Manual de usuario
SignaMax
SignaMax 065-1530 Manual de usuario
SignaMax
SignaMax 065-7940 Manual de usuario
SignaMax
SignaMax 065-7007A Manual de usuario
SignaMax
SignaMax 065-7341G Manual de usuario
SignaMax
SignaMax 065-7403HTB Manual de usuario
SignaMax
SignaMax 500-7624FE2GC Manual de usuario
SignaMax
SignaMax 065-7840 Manual de usuario
SignaMax
SignaMax 065-7508 Manual de usuario
SignaMax
SignaMax 065-7851 Manual de usuario
SignaMax
SignaMax 065-7408PTB Manual de usuario
SignaMax
SignaMax C-300 Series Manual de usuario
SignaMax
SignaMax 065-7404GATB Manual de usuario
SignaMax
SignaMax 065-7734 Manual de usuario
SignaMax
SignaMax 065-7861 Manual de programación
SignaMax
SignaMax 065-7532PoE Manual de usuario
SignaMax
SignaMax 065-7530 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad