SIGMA TEK TAE 1244 Manual de usuario

Date of creation: 03.06.2020 Version date: 11.11.2020 Article number: 12-200-1244-E

TAE 1244

Build-in Touch Terminal

Operating Manual

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: office@sigmatek.at

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation from German

distributed in any form (print, photocopy, microfilm or in any other process) without express permission.

We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in this handbook and assumes no responsibility for damages that

occur through its use.

BUILD-IN TOUCH TERMINAL TAE 1244

Build-in Touch Terminal TAE 1244

The multi-touch operating panel TAE 1244 is used to visualize automated processes. The

operation and monitoring of automated procedures are simplified using this display unit.

The projective capacitive touch screen is used to enter process data and parameters. The

output is shown on a 12.1“ TFT color display with LED backlighting.

This module operates with SIGMATEK HMI-LINK generation 2.1 (G2.1). This allows a

transmission from the display, as well as USB signals using standard cables (CAT-5e or

CAT-6) from a remote PC to a terminal (up to 100 m).

Currently supported: PC 452-K, HMI-Link G2 insert (PC 301-E7) and HMI-Link G2 Box (PC

301-E8). A device equipped with a generation 2.1 SIGMATEK HMI-Link (G2.1) is also

required on the PC side; either integrated directly on the PC or as an external expansion

box. With the 2 integrated USB connection, external end devices (mouse, keyboard ...) or

memory (USB stick) can be connection on the HMI side.

11.11.2020 Page 1

TAE 1244 BUILD-IN TOUCH TERMINAL

Table of Contents

1 Introduction 5

1.1 Target Group/Purpose of this Operating Manual 5

1.2 Important Reference Documentation 5

1.3 Contents of Delivery 5

2 Basic Safety Guidelines 6

2.1 Symbols Used 6

2.2 Disclaimer 8

2.3 General Safety Guidelines 9

3 Standards and Guidelines 11

3.1 Guidelines 11

3.1.1 EU Conformity Declaration 11

4 Technical Data 12

4.1 Performance Data 12

4.2 Electrical Requirements 12

4.3 Display 13

4.4 Control Unit 13

4.5 Minimum Distance between Operating Elements for Multi-touch Applications 14

4.6 Environmental Conditions 15

4.7 Miscellaneous 16

5 Interfaces 17

5.1 Front Connectors 17

5.1.1 X1: Supply (4-pin Phoenix RM 3.5) 17

5.1.2 X2: HMI Remote-IN (HMI-Link G2.1, Industrial Mini I/O) 18

5.1.3 X3: Service 18

5.1.4 X4, X5: USB 2.0 (Type A) 19

Page 2 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244

5.1.5 X6: Panel Interface Connector 19

5.2 Applicable Connectors 19

5.3 Status Display LEDs 20

6 Mechanical Dimensions 21

7 Assembly/Installation 23

7.1 Check Contents of Delivery 23

7.2 Installation 23

7.3 Mounting Instructions 23

7.3.1 Restricted Space Around Rear Trimming 24

7.3.2 Required Cutout for Mounting the Terminal 25

7.3.3 Mounting Position 26

8 Wiring 27

8.1 Grounding 27

8.2 Shielding 27

8.3 ESD Protection 28

8.4 USB Interface 28

9 Transport/Storage 29

10 Storage 30

11 Maintenance 31

11.1 Cleaning and Disinfecting the Touch Screen 31

11.2 Service 32

11.2.1 Calibrating the Touch Screen 32

11.3 Repair 32

11.4 Position Series Label Sub Device 33

12 Modularity 34

12.1 Removing the PIM from the Touch Panel 34

11.11.2020 Page 3

TAE 1244 BUILD-IN TOUCH TERMINAL

12.2 Mounting the PIM onto the Touch Panel 35

13 Display „Burn-In“ Effect 36

14 Disposal 37

15 Accessories 38

15.1 Touch Pen 38

Page 4 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

lProject planners

lTechnicians

lCommissioning engineers

lMachine operators

lMaintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

lTP XX61

lPIM 021

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x TAE 1244

8x angle bracket

1x 4-pin Phoenix connector plug

2x M3 TX10 Torx screws

11.11.2020 Page 5

TAE 1244 BUILD-IN TOUCH TERMINAL

2 Basic Safety Guidelines

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes.

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe the all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe the all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

Page 6 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe the all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Danger for ESD-sensitive components.

Les signes de danger pour les composants sensibles aux décharges

électrostatiques.

INFORMATION

Provides important information on the product, handling or

relevant sections of the documentation, which require

particular attention.

11.11.2020 Page 7

TAE 1244 BUILD-IN TOUCH TERMINAL

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual is

regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product description.

It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Page 8 11.11.2020

Tabla de contenidos

Otros manuales de Terminal táctil de SIGMA TEK

SIGMA TEK

SIGMA TEK TAE 2144 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 1844 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 1244 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 2154-W Manual de usuario

SIGMA TEK

SIGMA TEK ETT 2134 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 775 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 771 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 1034 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 1834 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 7321 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 731 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 2144-W Manual de usuario

SIGMA TEK

SIGMA TEK ETT 736 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 1544 Manual de usuario

SIGMA TEK

SIGMA TEK HBG 1012 Manual de usuario

SIGMA TEK

SIGMA TEK HZS 772 Manual de usuario

SIGMA TEK

SIGMA TEK TAE 1044 Manual de usuario

SIGMA TEK

SIGMA TEK ETT 2144 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario