SIGMA TEK IPN 021 Manual de usuario

IPN 021

S-DIAS PROFINET I/O Slave

Instruction Manual

Date of creation: 10.03.2015

Version date: 26.07.2023

Article number: 20-103-021-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax : +43/6274/4321-18

Email: office@sigmatek.at

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS PROFINET I/O SLAVE IPN 021

26.07.2023 Page 1

S-DIAS Profinet I/O Slave Module IPN 021

with 1 Profinet I/O IN

1 Profinet I/O OUT

The S-DIAS Profinet I/O slave module IPN 021 slave module is an

interface module between the S-DIAS control system and PROFINET

bus.

IPN 021 S-DIAS PROFINET I/O SLAVE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Performance Data.......................................................................13 
5.2 Electrical Requirements.............................................................14 
5.3 Miscellaneous .............................................................................16 
5.4 Environmental Conditions.........................................................16 
6Mechanical Dimensions........................................................17 
7Connector Layout..................................................................18 

 S-DIAS PROFINET I/O SLAVE IPN 021 
 
07.2023 Page 3 
1 Status LEDs.................................................................................19 
2 Applicable Connectors...............................................................20 
3 Label Field...................................................................................20 
8ESD Protection......................................................................21 
9Strain Relief ...........................................................................21 
Assembly/Installation ...........................................................23 
1 Check Contents of Delivery.......................................................23 
2 Mounting......................................................................................24 
Addressing.............................................................................26 
Supported Cycle Times ........................................................30 
1 Cycle Times below 1 ms (in µs).................................................30 
2 Cycle Times equal to or higher than 1 ms (in ms)...................30 
Hardware Class IPN021 ........................................................31 
1 Allgemein.....................................................................................32 
1.1 Communication Interfaces ................................................................ 35 
2 Global Methods...........................................................................35 
2.1 GetPDOSizes.................................................................................... 35 
2.2 GetPDOData..................................................................................... 36 
2.3 SetPDODat....................................................................................... 36 
2.4 AddSubModule ................................................................................. 37 
2.5 InstallCallback................................................................................... 38 

IPN 021 S-DIAS PROFINET I/O SLAVE 
 
Page 4 26.07.2023 
2.6 SendReadAnswer..............................................................................38 
2.7 SetProcessAlarm...............................................................................39 
2.8 AddDiagnosisAlarm...........................................................................40 
2.9 SetDiagnosisAlarm............................................................................40 
2.10 RemoveDiagnosisAlarm....................................................................41 
2.11 UpdateStringsInConfig ......................................................................41 
2.12 Reinitialize.........................................................................................41 
3 To be noticed...............................................................................41 
4 Example: Using Callbacks.........................................................42 
5 Using the GSD File with TIA (Siemens Design Environment) 48 
6 IPN and Profinet Bus Time Characteristics .............................51 
6.1 Detail View of IPN021 Timing on the Local S-DIAS Bus ...................52 
6.2 Detail View of S-DIAS Timing behind VARAN...................................56 
Transport/Storage..................................................................59 
Storage ...................................................................................59 
Maintenance...........................................................................60 
1 Service.........................................................................................60 
2 Repair...........................................................................................60 
Disposal..................................................................................60 
 

S-DIAS PROFINET I/O SLAVE IPN 021

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x IPN 021

IPN 021 S-DIAS PROFINET I/O SLAVE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS PROFINET I/O SLAVE IPN 021

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

IPN 021 S-DIAS PROFINET I/O SLAVE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Tabla de contenidos

Otros manuales de Sistema de E/S de SIGMA TEK

SIGMA TEK

SIGMA TEK TO 081 Manual de usuario

SIGMA TEK

SIGMA TEK SRO 022 Manual de usuario

SIGMA TEK

SIGMA TEK DI 160 Manual de usuario

SIGMA TEK

SIGMA TEK CSTO 082 Manual de usuario

SIGMA TEK

SIGMA TEK DI 080 Manual de usuario

SIGMA TEK

SIGMA TEK CO 041 Manual de usuario

SIGMA TEK

SIGMA TEK DI 204 Manual de usuario

SIGMA TEK

SIGMA TEK FC 021 Manual de usuario

SIGMA TEK

SIGMA TEK CP 931 Manual de usuario

SIGMA TEK

SIGMA TEK AI 075 Manual de usuario

SIGMA TEK

SIGMA TEK SR 012 Manual de usuario

SIGMA TEK

SIGMA TEK AO 081 Manual de usuario

SIGMA TEK

SIGMA TEK SDI 101 Manual de usuario

SIGMA TEK

SIGMA TEK DM 811 Manual de usuario

SIGMA TEK

SIGMA TEK DI 200 Manual de usuario

SIGMA TEK

SIGMA TEK C-DIAS Manual de instrucciones

SIGMA TEK

SIGMA TEK DM 822 Manual de usuario

SIGMA TEK

SIGMA TEK AI 040 Manual de usuario

SIGMA TEK

SIGMA TEK IO 011S Manual de usuario

SIGMA TEK

SIGMA TEK AI 088-1 Manual de usuario

SIGMA TEK

SIGMA TEK C-DIAS Series Manual de usuario

SIGMA TEK

SIGMA TEK TO 127 Manual de usuario

SIGMA TEK

SIGMA TEK SDI 101 Manual de usuario

SIGMA TEK

SIGMA TEK AO 026 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario