SIGLENT SDM3045X Manual de usuario

Quick Strat

SDM3045X Digital Multimeter

QS06034-E01A

2016 SIGLENT TECHNOLOGIES CO.,LTD

SIGLENT

SDM3045X Quick start I

● The information provided in this manual replaces all

information printed before.

● SIGLENT Company has the rights to change the

specification and the price.

● Contents in this manual are not allowed to be copied,

extracted and translated without permission by the

company.

SIGLENT

II SDM3045X Quick Start

General Safety Summary

Read the following safety precautions carefully to avoid any

personal injuries or damages to the instrument and any

products connected to it. To avoid potential hazards, please

use the instrument as specified.

Use proper power line.

It’s only allowed to use the special power line which is

approved by local state.

Ground the instrument.

The instrument is grounded through the protective terra

conductor of the power line. The ground conductor must be

connected to the earth to avoid electric shock. Make sure the

instrument is grounded correctly before connecting its input or

output terminals.

Connect the signal wire correctly

The potential of the signal wire is equal to the earth, so do not

connect the signal wire to a high voltage.

Observe all terminal ratings

Please observe all ratings and sign instructions on the

instrument to avoid fire or electric shock. Before connecting

the instrument, please read the manual carefully to gain more

information about the ratings.

Do not operate with suspected failures

If you suspect that the product is damaged, please contact

SIGLENT’s qualified service personnel to inspect it. Any repair

and adjustment to the product or replacing a component

should be done by qualified personnel only.

SIGLENT

SDM3045X Quick Start III

Avoid circuit or wire exposure

Don’t touch exposed contacts or components when the power

is on.

Don’t operate without covers.

Don’t operate the instrument with covers or panels removed.

Use proper fuse.

It’s only allowed to use the specified fuse for the instrument.

Use proper overvoltage protection.

Make sure there is no overvoltage (like voltage caused by

thunder and lightning) reaching to the instrument, otherwise

the operator may suffer an electric shock.

Antistatic protection.

Static electricity will cause damages to the instrument, so test

in antistatic areas as far as possible. Ground its inner and

outer conductors to release the static electricity temporarily

before connecting the cable to the instrument.

Keep good ventilation.

Improper ventilation will cause the rise of the instrument’s

temperature. Keep good ventilation and check the vent and

fan regularly when using it.

Keep the surface of the instrument clean and dry.

Do not operate in wet or damp conditions.

Do not operate in flammable or explosive environment.

The disturbance test of all the models meets the limit

values of A in the standard of EN 61326-1:2013.

SIGLENT

IV SDM3045X Quick Start

Input terminal protection limitation

Protection limitation is defined for the input terminal：

1. Main input（HI and LO）terminal

HI and LO terminals are used for Voltage, Resistance,

Capacitance, Continuity, Frequency, Diode and temperture

measurement. Two protection limitations are defined:

 HI-LO protection limitation: 1000VDC or 750AVC. It’s

the maximum measurable voltage. The limitation can be

expressed as 1000Vpk.

 LO-ground protection limitation：LO terminal can “float”

500Vpk relative to the ground safely. The maximum

protection limitation of HI terminal relative to the ground is

1000Vpk. Therefore, the sum of the “float” voltage and the

measured voltage can’t exceed 1000Vpk.

2. Sampling (HISense and LOSense) terminal

HISense and LOSense are used for 4-wire Resistance

measurement. Two protection limitations are defined:

 HISense-LOSense protection limitation: 2000Vpk.

 LOSense-LOSense protection limitation: 2Vpk.

3. Current input (I) terminal

I and LO terminals are used for current measurement. The

maximum current which go through the I terminal is limited to

10A by the fuse on the back panel.

NOTE:

Voltage on the current input terminal corresponds to voltage

on LO terminal. To keep good protection, only use the fuse of

specified type and level to replace this fuse.

SIGLENT

SDM3045X Quick Start V

IEC Measurement Category II Overvoltage Protection

SDM3045X Digital Multimeter provides overvoltage protection

for line-voltage mains connections meeting both of the

following conditions to avoid the danger of electric shock：

1. The HI and LO input terminals are connected to the

mains under Measurement Category II conditions as

following.

2. The maximum line voltage of the mains is 300VAC.

WARNING:

IEC Measurement Category II includes electrical devices

connected to mains at an outlet on a branch circuit, such as

most small appliances, test equipments, and other devices

that plug into a branch outlet or socket.

SDM3045X is capable of making measurements with the HI

and LO inputs connected to mains in such devices (up to

300VAC) or the branch outlet itself. However, the HI and LO

terminals of SDM3045X can’t be connected to mains in

permanently installed electrical devices such as the main

circuit-breaker panels, sub-panel disconnected boxes and

permanently wired motors. Such devices and circuits are

prone to exceed the protection limits of SDM3045X.

NOTE:

Voltages above 300VAC only can be measured in circuits that

are isolated from mains. However, there may be transient

overvoltage in circuits that are isolated from mains. SDM

3045X is able to withstand occasional transient overvoltage

up to 4000Vpk. Please don’t use this instrument to measure

circuits that transient overvoltage may exceed this level

SIGLENT

VI SDM3045X Quick Start

Safety Terms and Symbols

Terms in this manual. Terms may appear in this manual:

WARNING: Warning statements indicate the conditions and

behaviors that could result in injury or loss of life.

CAUTION: Caution statements indicate the conditions and

behaviors that could result in damage to this product

or other properties.

CAT I (1000V): IEC Measurement Category I. The highest

measurable voltage is 1000Vpk in the HI-LO terminal.

CAT II (300V): IEC Measurement Category II. Inputs may be

connected to mains (up to 300VAC) under Category II overvoltage

conditions.

Terms used on the instrument. Terms may appear on the

instrument:

DANGER indicates an injury or hazard that may immediately

happen.

WARNING indicates an injury or hazard that may not immediately

happen.

CAUTION indicates that a potential damage to the instrument or

other property might occur.

Symbols used on the instrument. Symbols may appear on the

instrument:

Hazardous Protective Warning Test Chassis

Voltage Earth Ground Ground Ground

SIGLENT

SDM3045X Quick Start VII

Daily Maintenance and Cleaning

Maintenance

When storing or placing the instrument, please avoid the

liquid crystal display from direct sunlight for a long time.

NOTE:

 To avoid damages to the instrument or test leads, please

don’t place them in mist, liquid or solvent.

Cleaning

Please often clean the instrument and test leads according

to the use of them.

 Wipe the external ash of the instrument and test leads by a

soft rag. Be careful not to scratch the transparent plastic

protective screen when cleaning the liquid crystal screen.

 Use a soft rag that has been soaked by water to clean the

instrument after cutting off the power. Or use 75%

isopropyl alcohol of water solvent to get a more thorough

cleaning.

NOTE:

 To prevent the surface of the instrument or test leads from

damages, please don’t use any corrosive or chemical

cleaning reagents.

Please make sure the instrument is already dry before

restarting it to avoid short circuits or personal injuries

caused by water.

SIGLENT

SDM3045X Quick Start VIII

Content

General Safety Summary ............................................................... II

Safety Terms and Symbols............................................................ VI

Daily Maintenance and Cleaning ................................................. VII

General Inspection .......................................................................... 1

Appearance and Size...................................................................... 2

To adjust the Handle ....................................................................... 3

Front Panel ....................................................................................... 4

Rear Panel ....................................................................................... 5

Connect Power Cord ....................................................................... 6

Power Selection ............................................................................... 7

Change the Power Fuse ................................................................. 7

Connect Test Leads ........................................................................ 8

Connect USB and LAN Ports ....................................................... 14

Use Safety Lock ............................................................................ 15

Troubleshooting ............................................................................. 16

Contact SIGLENT .......................................................................... 18

Otros manuales para SDM3045X

Tabla de contenidos

Otros manuales de Multímetro de SIGLENT

SIGLENT

SIGLENT SDM3065X Manual de usuario

SIGLENT

SIGLENT SDM3055A Manual de usuario

SIGLENT

SIGLENT SDM3055 Manual de usuario

SIGLENT

SIGLENT SDM3065X-SC Manual de usuario

SIGLENT

SIGLENT SDM3055 Manual de usuario

SIGLENT

SIGLENT SDM3000 Series Manual de usuario

SIGLENT

SIGLENT SDM3045X Manual de usuario

SIGLENT

SIGLENT SDM3065X Manual de usuario

SIGLENT

SIGLENT SDM3055-SC Manual de usuario

SIGLENT

SIGLENT SMM5065 Manual de usuario

SIGLENT

SIGLENT SDM3065X Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario