SIGLENT CPL5100 Manual de usuario

AC/DC Current Probe

CPL5100 (100A/600kHz)

600kHz

Preface

First of all, thank you for purchasing our products, this instruction manual is the

description about the function, usage, operation attention points, etc. Before use, please

read the instructions carefully and use correctly.

Manual annotation will use the following symbols to distinguish.



To avoid short out and deadly accident, the circuit under test should not surpass 600VAC



This probe is not designed for naked conductor.



Do not touch the conductor under test and the transducer probe during measuring.



When the oscilloscope is connected to other test terminal, please be careful for these

points:



Please use the fundamental insulation equipment with fitful voltage range and

pollution rate while the probe’s test terminal is connected to the other terminals.



Please do not surpass the safe voltage range if the fundamental insulation of the test

terminal cannot be met.



Please operate under correct guidance about electric safety.



There could be deadly electric shock if the device is damp or the users’ hand is wet.

Warning

Notice

Warning

In the case of wrong operation, the user risk injury. The content under this

mark records the relevant matters needing attention to avoid such dangers.

The user may suffer minor injuries and material damage with the wrong

operation. To avoid such situation, the matters under this mark need attention.

This symbol means it is harmful to the machine and human body; you must

strictly follow the instruction manual to operate.

Note

This symbolizes important note about how to use the machine.



The probe consists of precision components such as Magnetic core and Hall sensor,

which could be possibly damaged because of the sudden temperature change or external

force impact. Please be careful for vibration or impact.



The product is neither waterproof nor dustproof; please do not operate in the environment

filled with dust and water.



The probe’s upper and lower contact surfaces is made by precise polishing process.

Please protect this part or the probe could be malfunction.



When the battery voltage is lower than 6.5V, the probe will indicate a low voltage alert,

please change the battery. You can use a 9V alkaline battery for longer time.

CPL5100 Brief Summary

Type

Max current

(DC+Pk）

Max RMS

value

Band width

(-3dB)

Range

Current

transfer ratio

CPL5100

100A

70.7 Arms

600kHz

100A

0.01V/A

10A

0.1V/A

Attention

Note

Catalog

Preface…………………………………………… ……………………………………………1

CPL5100 Brief Summary……………………………………………………………….…......2

Summary ……………………………………………………………………………….……...4

Introduction about probe and accessories……………………………………………………...4

Electronic Characteristics……………………………………………………………………...6

Operating Method…………………………………………………………...…………………8

Mechanic Characteristics………………………………………………………………….…...9

Environment Characteristics…………………………………………………………………...9

Maintenance……………………………………………………………………………………9

Treatment if anything wrong……………………………………………………………….…10

Packing List……………………………………………………………...………………….. 10

1. Summary

CPL5100 is a kind of current probe that can measure both DC and AC current up to

100A (70.7Arms). The band width of CPL5100 is 600 kHz (-3dB).CPL5100 provides two

range option of 10A and 100A, the users may choose the correct range according to the

current value. The auto zero function make it easy for the users to operate, and it also has

power and low voltage indicator as well as overload sound alert. The probe can be powered

by battery or external power supply, which makes the measurement a lot more convenient.

With standard BNC output port, the probe can connect to any oscilloscope, and it can also

connect to multimeter with BNC-banana plug. The CPL5100 is usually used in power

supply , motor drive and power supply.

2. Introduction about probes and accessories



Probe



Power Switch:

ON: Power on and probe work; OFF:Power off and probe do not work.



Power indicator: When the power switch is on, the indicator is lighted green.



Battery Low Voltage Indicator: when the voltage of the battery is lower than 6.5V, the

power indicator will light red, reminding the users to change battery.



Range Switch: press the button switch to change between H and L Range.



Range Indicator: indicating the current Range choice. H level: 100A; L level: 10A.



Auto Zero button: to make accurate measurement, users need to do zero degaussing

before measuring to avoid the influence of environment factors like earth magnetic field

and temperature shift.



Auto Zero Indicator: when Auto Zero, the indicator is lighted on and in green and will

be turned off when the Auto Zero is finished.



Clamp: the clamp used for current measurement; the max diameter for the cable is

12mm.



External Power Supply Plug: powered by external DC supply.



Battery Box: standard 9V alkaline battery is used. Please turn off the switch and

disconnect from the conductor under test & oscilloscope when changing battery.



Accessories

Output Cable (CK-310):1 meter

Power Supply Adaptor (CK-612)：DC12V/1.2A

3. Electronic Characteristics

Test Condition: 23℃, 60%RH, cable under test get through the test center, load resistance

1MΩ

Range level

Current range

50mA~10A Peak

1A~100A Peak

Attenuation accuracy

0.1V/A

0.01V/A

Typical DC precision

3%±50mA

500mA~40A Peak ：

4%±50mA；40A~100A Peak ：

±15% Maximum

Band-width(-3dB)

DC-600kHz Refer to the typical Amplitude frequency

characteristic (Figure 1)

Max current VS frequency

characteristics curve

Figure 2

Phase shift

DC～65Hz：<1.5°

DC～65Hz：<1°

Typical DC linearity

The typical DC linearity at H level(0.01V/A), Figure 3

Rise time

≤583ns

Max operation current

Please refer to voltage and current rating table

Max operation voltage

Please refer to voltage and current rating table

Max floating voltage

Please refer to voltage and current rating table

Operating voltage RMS

CATI 600V CATII 600V CATIII 300V

Common mode voltage RMS

CATI 600V CATII 600V CATIII 300V

Typical battery type and life.

9V alkaline layer-built battery/ 15H

Low power indication

When battery voltage is lower than 6.5V, battery indicator

will turned red and alert.

Overload indication

When the current under test surpasses the range, the buzzer

will buzz

Voltage and current rating table

Parameter

Max operating current (A)

Max

operating

Max

floating

H(0.01V/A)

L(0.1V/A)

voltage (V)

voltage(V)

100

600

DC+AC peak value

100

600

AC peak value

100

600

AC peak to peak value

200

1200

- -

RMS CAT III

70.7

7.07

300

RMS CAT II

70.7

7.07

600

RMS CAT I

70.7

7.07

600

Figure 1 CPL5100 Typical Gain VS Frequency curve

Figure 2 Max current VS Frequency curve

Figure 3 Typical DC linearity (0.01V/A level)

4. Operating instruction



Set the coupling mode of the oscilloscope to DC and the input impedance to 1MΩ; To

make it easy to read, users can set the display unit of the oscilloscope from voltage to

current display. If user’s oscilloscope doesn’t have such function, user have to manually

set the corresponding attenuation ratio, for instance, if the probe is H level （0.01V/A）,

the oscilloscope should be 100X; if the probe is L level （0.1V/A）, oscilloscope is 10X.

User can connect the BNC output port with the input port of the oscilloscope with

standard double terminal BNC cable.



Turn the switch to ON, and the power indicator will light up green.



According to the value of the current under test, choose the correct range by pressing

button.

Attention: Different ranges correspond to different attenuation ratio of the oscilloscope.



Press the Auto Zero button. The buzzer will beep for twice, or it will have a long and

continuous beep meaning the failure of Auto Zero .The external magnetic field can have a

little influence to the DC zero, so do not move the device after Auto Zero.



Open the clamp of the probe and clamp the conductor under test.

Attention: There’s direction tip on the current probe clamp. If the direction of the current

fits the tip, output will be positive; On the contrary, the result is negative.



Adjust the vertical sensitivity of the oscilloscope to get a stable waveform.

5. Mechanic Characteristics

Size of the front current clamp

About 100*20*60mm

Size of the back output box

About 137*33*35mm

Operation altitude

0~2000 meter

Maximum diameter of the conductor

under test

12mm ø

Length of the cable connecting

current clamp and output box

1 meter

Length of double terminal BNC cable

1 meter

Weight

About 223g(without battery)

6. Environment characteristics

Operating temperature

0℃～+50℃

Storing temperature

-20℃～+80℃

Operating relative humidity

0℃to +40℃，95%RH；

+40℃~+50℃，45%RH

Pollution Degree

Level 2

7. Maintenance

If the product is in the warranty period and used correctly, and at the same time

the malfunction is caused by the flaws of product itself and have not been

disassemble, the company will give free repair to the product.



Clamp: Please keep the clamp clean. After long time use, please use soft cloth together

with alcohol to erase the dirt. Please keep the clamp away from damp environment, not

to mention direction contact with water.



Handle: Please use clean cloth or sponge to clean the handle. Please use little alcohol

instead of water to erase the dirt and parch it.

Tabla de contenidos

Otros manuales de Instrumento de medición de SIGLENT

SIGLENT

SIGLENT SSA3000X Plus Manual de usuario

SIGLENT

SIGLENT SSA5085A Manual de usuario

SIGLENT

SIGLENT SVA1000X Series Manual de usuario

SIGLENT

SIGLENT SSA3000X Plus Manual de usuario

SIGLENT

SIGLENT SHA850A Manual de usuario

SIGLENT

SIGLENT SDS2352X-E Manual de usuario

SIGLENT

SIGLENT SSA3000X Series Manual de usuario

SIGLENT

SIGLENT SP3150A Manual de usuario

SIGLENT

SIGLENT SNA5000A Manual de usuario

SIGLENT

SIGLENT SSA3050X-R Manual de usuario

SIGLENT

SIGLENT SSA3075X Plus Manual de usuario

SIGLENT

SIGLENT SHA852A Manual de usuario

SIGLENT

SIGLENT SHS800X Series Manual de usuario

SIGLENT

SIGLENT SVA1075X Manual de usuario

SIGLENT

SIGLENT SSA5000A Manual de usuario

SIGLENT

SIGLENT SNA5000A Manual de usuario

SIGLENT

SIGLENT SSA3021X Manual de usuario

SIGLENT

SIGLENT CP6000 Series Manual de usuario

SIGLENT

SIGLENT SM06035-E01A Manual de usuario

SIGLENT

SIGLENT SHA800A Manual de usuario

SIGLENT

SIGLENT SSA3000X-R Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario