Sigicom INFRA D10 Manual de usuario

INFRA D10

INFRA D10 Micro

Datalogger

Art no. 080-05010-0

Art no. 080-05030-0

Manual ver. C

Valid for firmware 1.2.0

 
 
Copyright © Sigicom AB 2020 2 
Table of Contents 
Introduction ........................................................................................5 
1. The INFRA System...................................................................5 
2. INFRA D10 Datalogger............................................................5 
3. INFRA D10 Micro Datalogger .................................................5 
4. Monitoring logic .......................................................................6 
4.1. Interval data..........................................................................6 
4.2. Transient data .......................................................................6 
5. Unpacking and Parts Identification...........................................7 
Safety instructions ..............................................................................8 
1. INFRA D10 Li-Ion battery........................................................8 
2. INFRA D10 Micro Lead Acid battery ......................................9 
Recycling..........................................................................................10 
Product Description..........................................................................10 
1. Keypad....................................................................................10 
2. Display....................................................................................11 
3. INFRA D10 Batteries..............................................................12 
4. Memory Card..........................................................................13 
5. SIM Cards...............................................................................13 
6. External Power Connector ......................................................16 
7. USB Connector (Micro-B Type).............................................16 
Configuration and Installation..........................................................17 
1. Configuration..........................................................................17 
1.1. Configuration for INFRA Net communication...................17 
1.2. Messages.............................................................................17 
1.3. Setting a non-default APN for a mini-SIM card.................19 
1.4. Remote live and Agenda.....................................................19 
1.5. Other configuration files.....................................................19 
2. Sensor network........................................................................20 
3. Startup Check..........................................................................23 
Operation..........................................................................................24 
1. Startup.....................................................................................24 

 
 
Copyright © Sigicom AB 2020 3 
2. Start Monitoring......................................................................25 
3. Monitoring Data......................................................................25 
4. Stop Monitoring......................................................................25 
5. INFRA Net Communication...................................................26 
5.1. Automatic INFRA Net Communication.............................26 
5.2. Manual INFRA Net Communication..................................27 
5.3. More Communication Information.....................................27 
6. Automatic Power Off..............................................................28 
7. Power Lost ..............................................................................28 
8. GUI Menu...............................................................................28 
8.1. Node config ........................................................................29 
8.2. Node info............................................................................30 
8.3. Network status....................................................................30 
8.4. Manual trigger ....................................................................30 
8.5. Settings and Actions ...........................................................30 
8.6. Errors codes........................................................................30 
9. Settings and actions.................................................................31 
9.1. Abort file upload.................................................................31 
9.2. Upload schedule .................................................................31 
9.3. Clock Set.............................................................................32 
9.4. Clock format.......................................................................32 
9.5. Alarm beacon X85..............................................................33 
9.6. USB Mode..........................................................................34 
9.7. Firmware upgrade...............................................................34 
9.8. Display off..........................................................................34 
9.9. Power Off and Reboot ........................................................35 
9.10. GUI Passcode .....................................................................36 
10. Disable Communication..........................................................36 
11. Time Synchronization through Internet ..................................37 
12. Daylight Saving Time.............................................................37 
13. INFRA Net Remote Control ...................................................37 
13.1. Force Reboot.......................................................................38 
14. Firmware Upgrade ..................................................................39 

 
 
Copyright © Sigicom AB 2020 4 
7. Technical Specifications...................................................................40 
8. Accessories.......................................................................................41 
9. Maintenance and Calibration............................................................42 
10.Contact and Support .........................................................................43 
Appendix A. Battery Level Limits ..........................................................44 
Appendix B. Li-Ion Battery Transport....................................................46 
Appendix C. Battery removal and installation ........................................47 
Appendix D. Mounting and transportation of INFRA D10 Micro ..........49 
Appendix E. Errors and Warnings ..........................................................51 
 
 

1. Introduction

1.1. The INFRA System

The INFRA system is a complete system for construction site monitoring,

from sensor to web presentation, including post processing and reporting

functions. Various ambient disturbances can be monitored, such as

vibrations, noise, dust and several geo-tech quantities.

1.2. INFRA D10 Datalogger

INFRA D10 is a digital datalogger replacing the older INFRA

Master/Mini. It is compatible with all bus cable connected sensors of the

INFRA system. Monitoring data is buffered on the memory card and is

sent when the next cellular communication takes place. If cellular

communication is not possible, data is kept for later transfer. SMS with

event data can be sent directly from the instrument to one or several cell

phones. Project administration, data presentation, reports, analysis and

graphs can easily be performed with INFRA Net.

1.3. INFRA D10 Micro Datalogger

INFRA D10 Micro replaces the older INFRA Micro. Differences from

INFRA D10 are:

•Lead-Acid battery instead of Li-Ion

•Industrial enclosure more suitable for permanent installation

•Antenna located inside the enclosure

•Multi-inlet cable gland instead of external power and USB

connectors

1.4. Monitoring logic

1.4.1. Interval data

Interval data are always monitored. An interval value is normally the

maximum value over the selected interval, but other operators than “max”

are sometimes used

. When the interval end time is reached, one value per

channel is saved, and a new interval is started. The timestamp of the

interval is the interval end time. The interval time is configured through

INFRA Net or the graphical user interface (GUI).

1.4.2. Transient data

When an instantaneous value exceeds the selected trigger level, a transient

recording is initiated. The trigger level can be changed through INFRA

Net or the graphical user interface.

It is very important to set adequate trigger levels. When set too high, there

will be no recordings. If on the other hand the level is set too low, there

will be lots of recordings, which would lead to:

• Increase of battery consumption.

• High data transfer rate/cost.

A transient recording can also be initiated via the Menu of the graphical

user interface. The maximum value of the channel transients is displayed

under the headline “EVT”, see section 4.2 for further description.

The static sensors (X20) cannot produce transients. Their trigger levels are

only used to make a connection to the INFRA Net server which then can

send a message about the event.

See the manual for each sensor you are using

1.5. Unpacking and Parts Identification

The D10 and D10 Micro are shipped in protective packaging. Please keep

this and use it when transporting your equipment. Any damage or

omission found when unpacking should be reported immediately to

Sigicom.

Keep record of the instrument’s serial number. You will be asked to give

this number in any communication you may have with Sigicom related to

this product.

2. Safety instructions

For mounting instructions for INFRA D10 Micro, see Appendix D.

For battery removal and installation instructions, see Appendix C.

2.1. INFRA D10 Li-Ion battery

•Only Sigicom B100 batteries are allowed to be used in INFRA

D10

•Only power supplies provided or recommended by Sigicom, see

chapter 8 Accessories.

•Do not use D10 batteries in other products than applicable

Sigicom products

•Under no circumstances, a charger which can supply more than

20.0V or 2A may be used

•Always keep the batteries at temperatures below 50ºC (122ºF)

•Do not incinerate or disassemble the batteries

•Do not immerse or expose the batteries in water

•If the terminals of the battery are shorted, the battery may

become very hot and permanently damaged

•Use stand-alone chargers in a well-ventilated room, well away

from flammable material, open fire, and electric sparks

•If the battery case is penetrated, it may burn with open flame

•Replacement and other handling of the batteries shall only be

executed by persons who have carefully read the safety

instructions in this manual and its referenced documents.

See Appendix B regarding Battery Transport

2.2. INFRA D10 Micro Lead Acid battery

•The short special battery cable included with the INFRA D10

Micro must be used for safety reasons (see chapter 8

Accessories).

•Remove the battery from the INFRA D10 Micro before

mounting, demounting, carrying or transporting.

•Use a nominal 12V, max 30Ah sealed Lead-Acid battery with the

INFRA D10 Micro

•Use battery AGM or Gel type of batteries to minimize risk of

leakage.

•Only use chargers provided or recommended by Sigicom, see

chapter 8 Accessories.

•Under no circumstances, a charger which can supply more than

14.7V or 3A may be used

•Never keep the battery in temperatures above 50 ºC (122 ºF)

•If battery is shorted, it may burn the operator or generate sparks.

•When charging the battery, in or out of the INFRA Datalogger,

place all parts in a well-ventilated room, away from open fire or

electric sparks.

•If misused, the battery may generate inflammable gas, smoke or

leak sulfuric acid.

•A worn-out battery, a battery with cracks or with signs to be

swollen or leaking should be replaced immediately.

•The INFRA D10 Micro shall be mounted upright with the battery

standing at the bottom of the enclosure.

•The battery strap included with the INFRA D10 Micro shall be

used to secure the battery.

•If an external battery is used, the internal battery must be

disconnected.

3. Recycling

This equipment falls under the Waste Electrical and Electronic Equipment

Directive (WEEE directive) 2012/19/EU, category 9: monitoring and

control instruments, and should be handled accordingly. Sigicom uses a

certified local partner for recycling of scrapped equipment.

The batteries used in this equipment falls under the Battery Directive

2006/66/EC:

•When the equipment is sold to customers in the European Union

(EU), except Sweden, the customer is the importer of the battery.

The customer must follow the rules and regulations as ratified by

each individual European Union member state for proper

disposal.

•Swedish customers can recycle the battery in the national battery

collection system.

•Users outside the EU must follow local rules and regulations for

proper disposal.

4. Product Description

4.1. Keypad

A six-button keypad is placed to the right of the display.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

MadgeTech

MadgeTech PRTemp140 Hoja de especificaciones

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario